Trieu Ngoc Ton
Trieu Ngoc Ton has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Bui Van Hien
Department of Industrial Automation, Faculty of Electrical and Electronic Engineering, Vietnam Aviation Academy, 104 Nguyen Van Troi Street, Phu Nhuan, Ho Chi Minh 70000, Vietnam
2 shared publications - Anh Viet Truong
Faculty of Electrical-Electronic Engineering, Ho Chi Minh City University of Technology and Engineering, Thu Duc, Ho Chi Minh City, Vietnam
1 shared publication Hoàng Ngọc Tuyến
Trường Cao đẳng Công nghệ Thủ Đức
1 shared publicationLoc Huu Pham
1 shared publicationLại Hoàng Hải
Trường Cao đẳng Công nghệ Thủ Đức
1 shared publication- Pham Vo Hong Nghi
Ho Chi Minh City University of Technology and Engineering
1 shared publication
Latest Publications
- Open Access
- 2 November 2026
- Published by Universitas Malikussaleh in International Journal of Engineering, Science and Information Technology
- Vol. 6 (4) , 190-199
Marginal Network Benefit-Aware Renewable DG Planning in Radial Distribution Systems
High penetration of renewable distributed generation (DG) does not necessarily imply efficient network utilization, because additional installed capacity may provide progressively smaller improvements in distribution-system performance. This paper proposes a marginal network benefit-aware planning framework for renewable DG in radial distribution networks (DNs). The framework combines a Composite Network Benefit (CNB), Marginal Renewable Benefit Index (MRBI), Normalized Marginal Benefit (NMB), and Renewable Benefit Saturation Point (RBSP) to quantify both overall network improvement and the incremental technical value of additional DG capacity. A Benefit-Guided Artificial Bee Colony (BGABC) algorithm is employed to optimize DG locations and capacities subject to voltage, generation, and power-balance constraints. The proposed approach is evaluated on the 33-bus and 69-bus radial distribution systems over renewable penetration levels from 20% to 70% and compared with conventional ABC, PSO, DE, SA, and GWO under consistent simulation conditions. Twenty independent runs are also performed to assess statistical robustness. The results show that active power loss, voltage deviation, and grid-related CO? emissions continue to improve as DG penetration increases, whereas the marginal network benefit declines progressively. The RBSP is identified at 60% penetration for the 33-bus system, corresponding to 2.232 MW of DG, 88.7 kW active power loss, and an NMB of 0.188, and at 70% for the 69-bus system, corresponding to 2.660 MW of DG, 143.8 kW active power loss, and an NMB of 0.105. These results confirm that renewable-benefit saturation is feeder-dependent and that additional DG may remain technically feasible beyond the point where its incremental network value becomes limited. The proposed framework therefore provides a complementary planning criterion for identifying effective DG allocations and technically meaningful renewable penetration levels in radial DNs
- 2 November 2026
- Published by Universitas Malikussaleh in International Journal of Engineering, Science and Information Technology
- Vol. 6 (4) , 190-199
Open AccessMarginal Network Benefit-Aware Renewable DG Planning in Radial Distribution Systems
High penetration of renewable distributed generation (DG) does not necessarily imply efficient network utilization, because additional installed capacity may provide progressively smaller improvements in distribution-system performance. This paper proposes a marginal network benefit-aware planning framework for renewable DG in radial distribution networks (DNs). The framework combines a Composite Network Benefit (CNB), Marginal Renewable Benefit Index (MRBI), Normalized Marginal Benefit (NMB), and Renewable Benefit Saturation Point (RBSP) to quantify both overall network improvement and the incremental technical value of additional DG capacity. A Benefit-Guided Artificial Bee Colony (BGABC) algorithm is employed to optimize DG locations and capacities subject to voltage, generation, and power-balance constraints. The proposed approach is evaluated on the 33-bus and 69-bus radial distribution systems over renewable penetration levels from 20% to 70% and compared with conventional ABC, PSO, DE, SA, and GWO under consistent simulation conditions. Twenty independent runs are also performed to assess statistical robustness. The results show that active power loss, voltage deviation, and grid-related CO? emissions continue to improve as DG penetration increases, whereas the marginal network benefit declines progressively. The RBSP is identified at 60% penetration for the 33-bus system, corresponding to 2.232 MW of DG, 88.7 kW active power loss, and an NMB of 0.188, and at 70% for the 69-bus system, corresponding to 2.660 MW of DG, 143.8 kW active power loss, and an NMB of 0.105. These results confirm that renewable-benefit saturation is feeder-dependent and that additional DG may remain technically feasible beyond the point where its incremental network value becomes limited. The proposed framework therefore provides a complementary planning criterion for identifying effective DG allocations and technically meaningful renewable penetration levels in radial DNs
- Open Access
- 23 October 2026
- Published by Tanjungpura University in ELKHA
- p. 169-176
Reserve-Constrained PV–BESS Co-Planning for Operationally Deliverable Hosting Capacity in Active Distribution Networks
Conventional photovoltaic (PV) hosting-capacity (HC) assessment generally focuses on the maximum installable PV capacity subject to voltage and thermal constraints. At the same time, renewable curtailment and the remaining operational flexibility of battery energy storage systems (BESSs) are often overlooked. This paper proposes a reserve-constrained PV–BESS co-planning framework to deliver hosting capacity operationally in active distribution networks. The model jointly optimizes PV and BESS siting and sizing, PV curtailment, inverter reactive power support, and battery operation under representative operating scenarios. A mixed-integer linear programming formulation, combined with an adaptive epsilon-constraint strategy, is employed to characterize the trade-off among HC, PV curtailment ratio (PCR), and flexibility reserve deficit (FRD). At the same time, candidate solutions are verified using nonlinear AC backward-/forward-sweep power-flow analysis. For the IEEE 33-bus system, the proposed solution achieves 62.9% HC with 2.1% PCR and 0.6% FRD, compared with 68.0%, 7.2%, and 4.8%, respectively, for unconstrained PV–BESS planning. For the IEEE 69-bus system, the corresponding values are 58.9%, 2.6%, and 0.8%, compared with 63.9%, 8.0%, and 5.4%. The main advantage of the proposed framework is that it explicitly preserves BESS upward and downward response capability while limiting excessive PV curtailment. Consequently, it provides a more operationally meaningful PV–BESS planning solution than approaches that maximize only nominal hosting capacity.
- 23 October 2026
- Published by Tanjungpura University in ELKHA
- p. 169-176
Open AccessReserve-Constrained PV–BESS Co-Planning for Operationally Deliverable Hosting Capacity in Active Distribution Networks
Conventional photovoltaic (PV) hosting-capacity (HC) assessment generally focuses on the maximum installable PV capacity subject to voltage and thermal constraints. At the same time, renewable curtailment and the remaining operational flexibility of battery energy storage systems (BESSs) are often overlooked. This paper proposes a reserve-constrained PV–BESS co-planning framework to deliver hosting capacity operationally in active distribution networks. The model jointly optimizes PV and BESS siting and sizing, PV curtailment, inverter reactive power support, and battery operation under representative operating scenarios. A mixed-integer linear programming formulation, combined with an adaptive epsilon-constraint strategy, is employed to characterize the trade-off among HC, PV curtailment ratio (PCR), and flexibility reserve deficit (FRD). At the same time, candidate solutions are verified using nonlinear AC backward-/forward-sweep power-flow analysis. For the IEEE 33-bus system, the proposed solution achieves 62.9% HC with 2.1% PCR and 0.6% FRD, compared with 68.0%, 7.2%, and 4.8%, respectively, for unconstrained PV–BESS planning. For the IEEE 69-bus system, the corresponding values are 58.9%, 2.6%, and 0.8%, compared with 63.9%, 8.0%, and 5.4%. The main advantage of the proposed framework is that it explicitly preserves BESS upward and downward response capability while limiting excessive PV curtailment. Consequently, it provides a more operationally meaningful PV–BESS planning solution than approaches that maximize only nominal hosting capacity.
- Open Access
- 29 June 2026
- Published by ECTI in ECTI Transactions on Electrical Engineering, Electronics, and Communications
- Vol. 24 (2)
Optimal Distributed Generation Planning for Loss Reduction and Phase Balancing in Unbalanced Distribution Networks Using the INFO Algorithm
This paper introduces an optimization framework for distributed generation (DG) planning in three phase unbalanced distribution networks (DN), aiming to jointly minimize active power losses and phase imbalance. Unlike conventional methods that assume balanced loading, the proposed model explicitly addresses phase asymmetry and single phase DG integration, common in real world low and medium voltage systems. A composite objective function is formulated, combining power loss with a normalized phase imbalance index under voltage and capacity constraints. The Weighted Mean of Vectors (INFO) algorithm, a recent metaheuristic with strong convergence properties, is applied to solve the mixed integer nonlinear problem. Simulation studies on modified IEEE 33 bus and 69-bus DN with realistic unbalanced loads show that INFO outperforms GWO, MPA, and AOA in loss reduction, phase balancing, and computational efficiency. These findings underscore the relevance of phase aware DG planning in enhancing the resilience and efficiency of modern distribution networks.
- 29 June 2026
- Published by ECTI in ECTI Transactions on Electrical Engineering, Electronics, and Communications
- Vol. 24 (2)
Open AccessOptimal Distributed Generation Planning for Loss Reduction and Phase Balancing in Unbalanced Distribution Networks Using the INFO Algorithm
This paper introduces an optimization framework for distributed generation (DG) planning in three phase unbalanced distribution networks (DN), aiming to jointly minimize active power losses and phase imbalance. Unlike conventional methods that assume balanced loading, the proposed model explicitly addresses phase asymmetry and single phase DG integration, common in real world low and medium voltage systems. A composite objective function is formulated, combining power loss with a normalized phase imbalance index under voltage and capacity constraints. The Weighted Mean of Vectors (INFO) algorithm, a recent metaheuristic with strong convergence properties, is applied to solve the mixed integer nonlinear problem. Simulation studies on modified IEEE 33 bus and 69-bus DN with realistic unbalanced loads show that INFO outperforms GWO, MPA, and AOA in loss reduction, phase balancing, and computational efficiency. These findings underscore the relevance of phase aware DG planning in enhancing the resilience and efficiency of modern distribution networks.
- 20 May 2026
- Published by Thai Nguyen University in TNU Journal of Science and Technology
- Vol. 231 (06) , 394-402
MULTI-OBJECTIVE PLANNING OF DISTRIBUTED GENERATION IN UNBALANCED THREE-PHASE DISTRIBUTION NETWORKS CONSIDERING VOLTAGE DEVIATION AND PHASE IMBALANCE
Bài báo đề xuất một khung quy hoạch đa mục tiêu nhằm xác định vị trí và công suất tối ưu của nguồn điện phân tán trong lưới điện phân phối ba pha không cân bằng. Mô hình tích hợp phân tích công suất ba pha chi tiết để phản ánh hiện tượng liên kết pha và tải không đối xứng trong thực tế. Bài toán tối ưu đồng thời tối thiểu tổn thất công suất tác dụng, độ lệch điện áp và mức mất cân bằng điện áp pha, dưới các ràng buộc về giới hạn điện áp nút, dòng nhánh và công suất phát. Phương pháp được kiểm chứng trên hệ thống 33 nút và 69 nút không cân bằng. Kết quả cho thấy so với trường hợp không có nguồn điện phân tán, phương pháp đề xuất đã giúp giảm tổn thất khoảng 45 - 46%, giảm độ lệch điện áp 42 - 48% và giảm chỉ số mất cân bằng pha đến 54%. Điều này khẳng định việc xem xét đầy đủ điều kiện ba pha không cân bằng có ý nghĩa quan trọng trong quy hoạch lưới điện phân phối hiện đại.
- 20 May 2026
- Published by Thai Nguyen University in TNU Journal of Science and Technology
- Vol. 231 (06) , 394-402
MULTI-OBJECTIVE PLANNING OF DISTRIBUTED GENERATION IN UNBALANCED THREE-PHASE DISTRIBUTION NETWORKS CONSIDERING VOLTAGE DEVIATION AND PHASE IMBALANCE
Bài báo đề xuất một khung quy hoạch đa mục tiêu nhằm xác định vị trí và công suất tối ưu của nguồn điện phân tán trong lưới điện phân phối ba pha không cân bằng. Mô hình tích hợp phân tích công suất ba pha chi tiết để phản ánh hiện tượng liên kết pha và tải không đối xứng trong thực tế. Bài toán tối ưu đồng thời tối thiểu tổn thất công suất tác dụng, độ lệch điện áp và mức mất cân bằng điện áp pha, dưới các ràng buộc về giới hạn điện áp nút, dòng nhánh và công suất phát. Phương pháp được kiểm chứng trên hệ thống 33 nút và 69 nút không cân bằng. Kết quả cho thấy so với trường hợp không có nguồn điện phân tán, phương pháp đề xuất đã giúp giảm tổn thất khoảng 45 - 46%, giảm độ lệch điện áp 42 - 48% và giảm chỉ số mất cân bằng pha đến 54%. Điều này khẳng định việc xem xét đầy đủ điều kiện ba pha không cân bằng có ý nghĩa quan trọng trong quy hoạch lưới điện phân phối hiện đại.
- Open Access
- 1 April 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 16 (2) , 598-607
Multi-objective optimization of distributed generation placement and sizing in active distribution networks considering harmonic distortion
This paper presents a multi-objective optimization model for optimal placement and sizing of inverter-based distributed generation (DG) units in active distribution power systems (DPS), considering their impact on harmonic distortion. The model simultaneously minimizes total power losses and total harmonic distortion (THD), ensuring compliance with IEEE 519 standards. To solve this problem, the reptile search algorithm (RUN) is applied and compared with three metaheuristic algorithms: multi-objective particle swarm optimization (MOPSO), multi-objective grey wolf optimizer (MOGWO), and multi-objective whale optimization algorithm (MOWOA). Simulation results on IEEE 33-bus and 69-bus systems show that reptile search algorithm (RUN) reduces power losses by up to 6.1% and THD by 21.7% compared to MOPSO. Moreover, the results confirm a strong correlation between DG output power and harmonic amplitudes, highlighting the importance of power quality aware DG planning.
- 1 April 2026
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 16 (2) , 598-607
Open AccessMulti-objective optimization of distributed generation placement and sizing in active distribution networks considering harmonic distortion
This paper presents a multi-objective optimization model for optimal placement and sizing of inverter-based distributed generation (DG) units in active distribution power systems (DPS), considering their impact on harmonic distortion. The model simultaneously minimizes total power losses and total harmonic distortion (THD), ensuring compliance with IEEE 519 standards. To solve this problem, the reptile search algorithm (RUN) is applied and compared with three metaheuristic algorithms: multi-objective particle swarm optimization (MOPSO), multi-objective grey wolf optimizer (MOGWO), and multi-objective whale optimization algorithm (MOWOA). Simulation results on IEEE 33-bus and 69-bus systems show that reptile search algorithm (RUN) reduces power losses by up to 6.1% and THD by 21.7% compared to MOPSO. Moreover, the results confirm a strong correlation between DG output power and harmonic amplitudes, highlighting the importance of power quality aware DG planning.
- 5 February 2026
- Published by Thai Nguyen University in TNU Journal of Science and Technology
- Vol. 231 (02) , 97-104
QUY HOẠCH NGUỒN ĐIỆN PHÂN TÁN TRONG LƯỚI ĐIỆN PHÂN PHỐI NHẰM TĂNG HIỆU QUẢ HẤP THỤ NĂNG LƯỢNG TÁI TẠO SỬ DỤNG THUẬT TOÁN SECRETARY BIRD ALGORITHM
Bài báo này giới thiệu một phương pháp tối ưu hóa đa mục tiêu mới cho bài toán quy hoạch nguồn điện phân tán trong lưới điện phân phối, nhằm giảm tổn thất công suất, cải thiện chất lượng điện áp và tăng hiệu quả sử dụng năng lượng tái tạo. Phương pháp được phát triển dựa trên Secretary Bird Algorithm là thuật toán metaheuristic mô phỏng hành vi quan sát, tấn công và né tránh của loài chim Secretary trong tự nhiên. Cơ chế hoạt động của Secretary Bird giúp cân bằng giữa thăm dò toàn cục và khai thác cục bộ, cải thiện độ chính xác tìm kiếm và tránh hội tụ sớm. Mô hình tối ưu xem xét bốn mục tiêu gồm giảm tổn thất công suất, chi phí đầu tư, độ lệch điện áp và tăng tỷ lệ hấp thụ năng lượng tái tạo, đồng thời tuân thủ các ràng buộc kỹ thuật. Kết quả trên lưới điện 33 nút và 69 nút cho thấy thuật toán đề xuất đạt tốc độ hội tụ nhanh, tổn thất thấp và hiệu quả cao, khẳng định tiềm năng ứng dụng trong quy hoạch lưới điện thông minh và bền vững.
- 5 February 2026
- Published by Thai Nguyen University in TNU Journal of Science and Technology
- Vol. 231 (02) , 97-104
QUY HOẠCH NGUỒN ĐIỆN PHÂN TÁN TRONG LƯỚI ĐIỆN PHÂN PHỐI NHẰM TĂNG HIỆU QUẢ HẤP THỤ NĂNG LƯỢNG TÁI TẠO SỬ DỤNG THUẬT TOÁN SECRETARY BIRD ALGORITHM
Bài báo này giới thiệu một phương pháp tối ưu hóa đa mục tiêu mới cho bài toán quy hoạch nguồn điện phân tán trong lưới điện phân phối, nhằm giảm tổn thất công suất, cải thiện chất lượng điện áp và tăng hiệu quả sử dụng năng lượng tái tạo. Phương pháp được phát triển dựa trên Secretary Bird Algorithm là thuật toán metaheuristic mô phỏng hành vi quan sát, tấn công và né tránh của loài chim Secretary trong tự nhiên. Cơ chế hoạt động của Secretary Bird giúp cân bằng giữa thăm dò toàn cục và khai thác cục bộ, cải thiện độ chính xác tìm kiếm và tránh hội tụ sớm. Mô hình tối ưu xem xét bốn mục tiêu gồm giảm tổn thất công suất, chi phí đầu tư, độ lệch điện áp và tăng tỷ lệ hấp thụ năng lượng tái tạo, đồng thời tuân thủ các ràng buộc kỹ thuật. Kết quả trên lưới điện 33 nút và 69 nút cho thấy thuật toán đề xuất đạt tốc độ hội tụ nhanh, tổn thất thấp và hiệu quả cao, khẳng định tiềm năng ứng dụng trong quy hoạch lưới điện thông minh và bền vững.
- Open Access
- 1 January 2026
- Published by Wiley in Journal of Engineering
- Vol. 2026 (1)
Data‐Driven Prediction of Photovoltaic Inverter Temperature Using Operational Dashboard Data: A Comparative Machine Learning Study
Effective thermal management is crucial to PV inverter reliability and lifetime, as power electronic components are highly sensitive to thermal stress. However, many existing monitoring methods rely on complex simulations or costly experiments. This study proposes a data‐driven approach to predict inverter temperature using standard variables from online monitoring dashboards. Five machine‐learning models, such as decision tree, random forest, gradient boosting, histogram‐based gradient boosting, and XGBoost, were evaluated; random forest performed best on an independent test set (R 2 = 0.9947, RMSE = 0.601°C, MAE = 0.471°C). SHAP analysis further provided interpretability and revealed a clear inverse relationship between reactive power and inverter temperature, alongside the effects of the daily cycle and power output. Overall, subdegree (< 1°C) accuracy was achieved with only seven input features, enabling a practical, cost‐effective solution for predictive maintenance and real‐time monitoring.
- 1 January 2026
- Published by Wiley in Journal of Engineering
- Vol. 2026 (1)
Open AccessData‐Driven Prediction of Photovoltaic Inverter Temperature Using Operational Dashboard Data: A Comparative Machine Learning Study
Effective thermal management is crucial to PV inverter reliability and lifetime, as power electronic components are highly sensitive to thermal stress. However, many existing monitoring methods rely on complex simulations or costly experiments. This study proposes a data‐driven approach to predict inverter temperature using standard variables from online monitoring dashboards. Five machine‐learning models, such as decision tree, random forest, gradient boosting, histogram‐based gradient boosting, and XGBoost, were evaluated; random forest performed best on an independent test set (R 2 = 0.9947, RMSE = 0.601°C, MAE = 0.471°C). SHAP analysis further provided interpretability and revealed a clear inverse relationship between reactive power and inverter temperature, alongside the effects of the daily cycle and power output. Overall, subdegree (< 1°C) accuracy was achieved with only seven input features, enabling a practical, cost‐effective solution for predictive maintenance and real‐time monitoring.
- 26 November 2025
- Published by Thai Nguyen University in TNU Journal of Science and Technology
- Vol. 230 (14) , 377-384
TỐI ƯU HÓA NGUỒN ĐIỆN PHÂN TÁN NHẰM GIẢM TỔN THẤT CÔNG SUẤT VÀ ĐỘ LỆCH PHA TRONG HỆ THỐNG ĐIỆN PHÂN PHỐI BA PHA KHÔNG ĐỐI XỨNG
Bài báo này trình bày một phương pháp tối ưu hóa đa mục tiêu cho bài toán quy hoạch nguồn phát phân tán trong lưới điện phân phối ba pha không đối xứng. Mô hình đề xuất xét đến các bất đối xứng thực tế trong lưới điện như trở kháng đường dây không đồng đều, phân bố tải lệch pha và các nguồn phát một pha hoặc hai pha. Mục tiêu tối ưu là giảm tổn thất công suất, sai lệch điện áp và độ lệch pha. Giải thuật Weighted Interaction Optimizer được áp dụng để giải bài toán phi tuyến có biến hỗn hợp. Phương pháp được kiểm nghiệm trên hai lưới điện tiêu chuẩn gồm 18 nút và 33 nút. Kết quả mô phỏng cho thấy phương pháp đạt hiệu quả cao trong việc giảm tổn thất công suất và cải thiện cân bằng pha, đặc biệt trong điều kiện lưới không đối xứng. Mô hình là một giải pháp hiệu quả và thực tiễn cho việc tích hợp các nguồn năng lượng tái tạo vào lưới điện phân phối hiện đại.
- 26 November 2025
- Published by Thai Nguyen University in TNU Journal of Science and Technology
- Vol. 230 (14) , 377-384
TỐI ƯU HÓA NGUỒN ĐIỆN PHÂN TÁN NHẰM GIẢM TỔN THẤT CÔNG SUẤT VÀ ĐỘ LỆCH PHA TRONG HỆ THỐNG ĐIỆN PHÂN PHỐI BA PHA KHÔNG ĐỐI XỨNG
Bài báo này trình bày một phương pháp tối ưu hóa đa mục tiêu cho bài toán quy hoạch nguồn phát phân tán trong lưới điện phân phối ba pha không đối xứng. Mô hình đề xuất xét đến các bất đối xứng thực tế trong lưới điện như trở kháng đường dây không đồng đều, phân bố tải lệch pha và các nguồn phát một pha hoặc hai pha. Mục tiêu tối ưu là giảm tổn thất công suất, sai lệch điện áp và độ lệch pha. Giải thuật Weighted Interaction Optimizer được áp dụng để giải bài toán phi tuyến có biến hỗn hợp. Phương pháp được kiểm nghiệm trên hai lưới điện tiêu chuẩn gồm 18 nút và 33 nút. Kết quả mô phỏng cho thấy phương pháp đạt hiệu quả cao trong việc giảm tổn thất công suất và cải thiện cân bằng pha, đặc biệt trong điều kiện lưới không đối xứng. Mô hình là một giải pháp hiệu quả và thực tiễn cho việc tích hợp các nguồn năng lượng tái tạo vào lưới điện phân phối hiện đại.
- Open Access
- 11 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 129588-129600
Fast and Accurate GMPPT Based on Modified P&O Algorithm
The most significant challenge the maximum power point tracking (MPPT) algorithms face is reaching the global MPPT under partial shading conditions (PSC). In this case, the power-voltage (P-V) and current-voltage (I-V) characteristic curves of the photovoltaic (PV) system produce many maximum power points, which is the reason that the algorithms often trapped in local maximum power point (LMPP). The Perturbation and Observation (P&O) algorithm is simple and effective for finding MPP on a mono-extreme graph. Under PSC with many extremes, it is necessary to limit the range of potential GMPP so that this algorithm can avoid the LMPP trap. This paper introduces a global MPPT (GMPPT) method based on the combination of modified P&O and simulates the behavior of the I-V curve under PSC. In particular, the starting parameters of the algorithm are adjusted in the potential GMPP region to exploit simplicity and efficiency to increase performance and convergence speed. The proposed method determines the area where the GMPP is potentially found more accurately, and this contribution is crucial for increasing the efficiency of the strings of PV arrays under partial shading conditions. By comparing results with other algorithms, such as Modified P&O, Adaptive Jaya (Ajaya), and Jaya, the proposed algorithm has verified its outstanding advantages in MPPT performance and search time under the same test conditions.
- 11 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 129588-129600
Open AccessFast and Accurate GMPPT Based on Modified P&O Algorithm
The most significant challenge the maximum power point tracking (MPPT) algorithms face is reaching the global MPPT under partial shading conditions (PSC). In this case, the power-voltage (P-V) and current-voltage (I-V) characteristic curves of the photovoltaic (PV) system produce many maximum power points, which is the reason that the algorithms often trapped in local maximum power point (LMPP). The Perturbation and Observation (P&O) algorithm is simple and effective for finding MPP on a mono-extreme graph. Under PSC with many extremes, it is necessary to limit the range of potential GMPP so that this algorithm can avoid the LMPP trap. This paper introduces a global MPPT (GMPPT) method based on the combination of modified P&O and simulates the behavior of the I-V curve under PSC. In particular, the starting parameters of the algorithm are adjusted in the potential GMPP region to exploit simplicity and efficiency to increase performance and convergence speed. The proposed method determines the area where the GMPP is potentially found more accurately, and this contribution is crucial for increasing the efficiency of the strings of PV arrays under partial shading conditions. By comparing results with other algorithms, such as Modified P&O, Adaptive Jaya (Ajaya), and Jaya, the proposed algorithm has verified its outstanding advantages in MPPT performance and search time under the same test conditions.