L. M. Kapitanchuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
L. M. Kapitanchuk has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
A. B. Ataubaeva
National Academy of Sciences of Ukraine
1 shared publicationA. V. Zorenko
Orion Research Institute
1 shared publication- Alexander E. Belyaev
V. Lashkaryov Institute of Semiconductor Physics, National Academy of Sciences of Ukraine , Pr. Nauky 41, 03680 Kyiv, Ukraine
1 shared publication - Anatolii A. Bondar
Frantsevich Institute for Problems of Materials Science, N.A.S. of Ukraine, Kyiv, Ukraine
1 shared publication - Andrian V. Kuchuk
Institute for Nanoscience and Engineering, University of Arkansas 1 , Fayetteville, Arkansas 72701, USA
1 shared publication - I. V. Oleksenko1 shared publication
Latest Publications
- Open Access
- 30 September 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metaloznavstvo ta obrobka metalìv
- Vol. 30 (3) , 11-21
Peculiarities of structure formation of copper-doped post-eutectoid steels
The structural state of pre-eutectoid steels alloyed with copper in the range of up to 28% was studied. It was established that the alloying of steel with a carbon content of 1.3% with copper in the amount of 8, 12 and 28% leads to the formation of the primary and secondary copper -phase The main metallic component of the structure of the studied copper-alloyed steels is represented by thin-plate copper pearlite with inclusions on the boundaries of the primary austenite grains of secondary cementite and secondary inclusions of the copper -phase. The results of the X-ray spectral microanalysis showed that the primary copperite of the -phase consists of 92.5% of copper and 7.1% of iron. The transition zone between the primary copper precipitate and the matrix, the distribution of chemical elements in it, was studied. The total size of the interphase zone is 0.4 μm. It was established that alloying of steels with 8-28% copper contributes to the formation of a highly dispersed structure of copper thin-plate pearlite, as well as the formation of areas with deformed microvolumes near the primary copper e-phase, which constitute a significant barrier to the movement of dislocations. Thus, a state with increased resistance to dynamic loads has been formed at the micro level. The obtained results open up the possibility of using post-eutectoid steels alloyed with copper in the corresponding highly loaded products Keywords: structure, post-eutectoid steel, alloying, thin-plate pearlite, e-phase, iron, spectrum.
- 30 September 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metaloznavstvo ta obrobka metalìv
- Vol. 30 (3) , 11-21
Open AccessPeculiarities of structure formation of copper-doped post-eutectoid steels
The structural state of pre-eutectoid steels alloyed with copper in the range of up to 28% was studied. It was established that the alloying of steel with a carbon content of 1.3% with copper in the amount of 8, 12 and 28% leads to the formation of the primary and secondary copper -phase The main metallic component of the structure of the studied copper-alloyed steels is represented by thin-plate copper pearlite with inclusions on the boundaries of the primary austenite grains of secondary cementite and secondary inclusions of the copper -phase. The results of the X-ray spectral microanalysis showed that the primary copperite of the -phase consists of 92.5% of copper and 7.1% of iron. The transition zone between the primary copper precipitate and the matrix, the distribution of chemical elements in it, was studied. The total size of the interphase zone is 0.4 μm. It was established that alloying of steels with 8-28% copper contributes to the formation of a highly dispersed structure of copper thin-plate pearlite, as well as the formation of areas with deformed microvolumes near the primary copper e-phase, which constitute a significant barrier to the movement of dislocations. Thus, a state with increased resistance to dynamic loads has been formed at the micro level. The obtained results open up the possibility of using post-eutectoid steels alloyed with copper in the corresponding highly loaded products Keywords: structure, post-eutectoid steel, alloying, thin-plate pearlite, e-phase, iron, spectrum.
- 1 May 2020
- Published by Springer Nature in Powder Metallurgy and Metal Ceramics
- Vol. 59 (1-2) , 89-105
Solidus Surface of the Mo–Fe–B System
- 1 May 2020
- Published by Springer Nature in Powder Metallurgy and Metal Ceramics
- Vol. 59 (1-2) , 89-105
Solidus Surface of the Mo–Fe–B System
- 20 February 2011
- Published by Pleiades Publishing Ltd in Semiconductors
- Vol. 45 (2) , 253-259
Effect of p-n junction overheating on degradation of silicon high-power pulsed IMPATT diodes
The thermal limits of the two-drift impact avalanche and transit-time (IMPATT) diode operating in the pulsed mode in the 8-mm wavelength region with a microwave power as high as 30–35 W have been...
- 20 February 2011
- Published by Pleiades Publishing Ltd in Semiconductors
- Vol. 45 (2) , 253-259
Effect of p-n junction overheating on degradation of silicon high-power pulsed IMPATT diodes
The thermal limits of the two-drift impact avalanche and transit-time (IMPATT) diode operating in the pulsed mode in the 8-mm wavelength region with a microwave power as high as 30–35 W have been...