Mei Deng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mei Deng has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Qiuyun Zhang
Key Laboratory of Agricultural Resources and Environment in High Education Institute of Guizhou Province, Anshun University, Anshun, China
3 shared publications - Yutao Zhang
Key Laboratory of Agricultural Resources and Environment in High Education Institute of Guizhou Province, Anshun University, Anshun, China
3 shared publications - Zheng-Jun Liu
Key Laboratory of Agricultural Resources and Environment in High Education , Institute of Guizhou Province Anshun University , Anshun , 561000 , P.R. China
3 shared publications - Jingsong Cheng
School of Chemistry and Chemical Engineering Anshun University Anshun Guizhou China
2 shared publications - Ting Li
School of Chemistry and Chemical Engineering Anshun University Anshun Guizhou China
2 shared publications - Yanhui Lei
School of Chemistry and Chemical Engineering Anshun University Anshun Guizhou China
2 shared publications
Latest Publications
- 19 May 2025
- Published by Wiley in Applied Organometallic Chemistry
- Vol. 39 (6)
Different Ligand Functionalized Al‐Based MOFs as a Support for Impregnation of Heteropoly Acid for Efficient Esterification Reactions
The development of metal–organic frameworks (MOFs)–based heterogeneous catalysts with both Lewis acid and Brønsted acid sites has proved to be promising and useful because they offer an economical route to synthesize environment‐friendly biofuels. Here, a series of Al‐based MOFs, functionalized by single ‐H, ‐NH2, and ‐NO2 groups, are successfully synthesized and applied as supports to load phosphomolybdic acid (HPMo) through a facile one‐pot hydrothermal method, by forming composites of HPMo@Al‐MOFs‐X (where X = ‐H, ‐NH2, and ‐NO2), and it was used to esterify fatty acids into biodiesel. The structural features of the prepared hybrid materials were evaluated by various techniques, including XRD, FTIR, BET, SEM‐EDS, NH3‐TPD, Py‐FTIR, TG, and XPS. The material characterization revealed that the catalytic behavior of the prepared HPMo@AlB composite is better than HPMo@AlB‐NH2, HPMo@AlB‐NO2, and pure AlB. The optimized conversion of oleic acid (OA) is 97.5% under the optimized reaction conditions. Moreover, the composite maintained above 90% conversion after nine cycles and demonstrated excellent reusability. This outstanding catalytic activity and stability is mainly attributed to the large specific surface area (138.4 m2/g), appropriate pore volume (0.47 cm3/g), and mesoscale pore size (17.7 nm) of HPMo@AlB composite that reduced the mass transfer resistance, high total acidity, and the synergistic effect of Lewis acid and Brønsted acid sites and ensures efficient esterification. The present research introduces an important reference for advancing high‐performance MOFs‐based hybrid materials to industrialize biofuels production.
- 19 May 2025
- Published by Wiley in Applied Organometallic Chemistry
- Vol. 39 (6)
Different Ligand Functionalized Al‐Based MOFs as a Support for Impregnation of Heteropoly Acid for Efficient Esterification Reactions
The development of metal–organic frameworks (MOFs)–based heterogeneous catalysts with both Lewis acid and Brønsted acid sites has proved to be promising and useful because they offer an economical route to synthesize environment‐friendly biofuels. Here, a series of Al‐based MOFs, functionalized by single ‐H, ‐NH2, and ‐NO2 groups, are successfully synthesized and applied as supports to load phosphomolybdic acid (HPMo) through a facile one‐pot hydrothermal method, by forming composites of HPMo@Al‐MOFs‐X (where X = ‐H, ‐NH2, and ‐NO2), and it was used to esterify fatty acids into biodiesel. The structural features of the prepared hybrid materials were evaluated by various techniques, including XRD, FTIR, BET, SEM‐EDS, NH3‐TPD, Py‐FTIR, TG, and XPS. The material characterization revealed that the catalytic behavior of the prepared HPMo@AlB composite is better than HPMo@AlB‐NH2, HPMo@AlB‐NO2, and pure AlB. The optimized conversion of oleic acid (OA) is 97.5% under the optimized reaction conditions. Moreover, the composite maintained above 90% conversion after nine cycles and demonstrated excellent reusability. This outstanding catalytic activity and stability is mainly attributed to the large specific surface area (138.4 m2/g), appropriate pore volume (0.47 cm3/g), and mesoscale pore size (17.7 nm) of HPMo@AlB composite that reduced the mass transfer resistance, high total acidity, and the synergistic effect of Lewis acid and Brønsted acid sites and ensures efficient esterification. The present research introduces an important reference for advancing high‐performance MOFs‐based hybrid materials to industrialize biofuels production.
- 5 February 2025
- Published by Wiley in Applied Organometallic Chemistry
- Vol. 39 (3)
In Situ Fabrication of AgI/MIL‐101(Cr) Nanocomposite Catalyst With Enhancing Photocatalytic Degradation of Organic Dye Molecules From Wastewater
The construction and optimization of an effective photocatalyst for photodegradation of persistent recalcitrant organic remains challenging. In this work, MIL‐101(Cr)‐based nanocomposites (AgI@MCr) are proposed to be fabricated by a simple, green solvent, and room temperature in situ preparation strategy, achieving a highly efficient photocatalytic degradation of organic dye rhodamine B (RhB) molecule under visible light irradiation. Extensive characterization (XRD, FTIR, N2 adsorption–desorption, SEM and EDS, TG, XPS, UV–vis DRS, PL, transient photocurrent, and EIS) confirmed the composite material's structure, morphology, elemental composition, and optical characteristics. Among all the prepared nanocomposites, AgI@MCr‐2 demonstrates outstanding photocatalytic performance for RhB with a removal efficiency of 95.4% within 70 min, and a reaction kinetics of 0.0392 min−1, superior to pristine AgI or MIL‐101(Cr), and also shows excellent durability, retaining over 80% RhB degradation efficiency after four cycles. Remarkably, the significant enhancement is attributed to the built interfacial contact and synergistic effect between substances in the nanocomposite, high specific surface area, strong visible light–harvesting capacity, low bandgaps, and high electron–hole pair separation. In addition, a possible degradation route for the AgI@MCr nanocomposite is further proposed using various analysis techniques. This study provides valuable references for developing effective multicomponent MOF‐based photocatalytic composite materials for dyeing wastewater treatment and environmental remediation.
- 5 February 2025
- Published by Wiley in Applied Organometallic Chemistry
- Vol. 39 (3)
In Situ Fabrication of AgI/MIL‐101(Cr) Nanocomposite Catalyst With Enhancing Photocatalytic Degradation of Organic Dye Molecules From Wastewater
The construction and optimization of an effective photocatalyst for photodegradation of persistent recalcitrant organic remains challenging. In this work, MIL‐101(Cr)‐based nanocomposites (AgI@MCr) are proposed to be fabricated by a simple, green solvent, and room temperature in situ preparation strategy, achieving a highly efficient photocatalytic degradation of organic dye rhodamine B (RhB) molecule under visible light irradiation. Extensive characterization (XRD, FTIR, N2 adsorption–desorption, SEM and EDS, TG, XPS, UV–vis DRS, PL, transient photocurrent, and EIS) confirmed the composite material's structure, morphology, elemental composition, and optical characteristics. Among all the prepared nanocomposites, AgI@MCr‐2 demonstrates outstanding photocatalytic performance for RhB with a removal efficiency of 95.4% within 70 min, and a reaction kinetics of 0.0392 min−1, superior to pristine AgI or MIL‐101(Cr), and also shows excellent durability, retaining over 80% RhB degradation efficiency after four cycles. Remarkably, the significant enhancement is attributed to the built interfacial contact and synergistic effect between substances in the nanocomposite, high specific surface area, strong visible light–harvesting capacity, low bandgaps, and high electron–hole pair separation. In addition, a possible degradation route for the AgI@MCr nanocomposite is further proposed using various analysis techniques. This study provides valuable references for developing effective multicomponent MOF‐based photocatalytic composite materials for dyeing wastewater treatment and environmental remediation.
- 1 October 2024
- Published by Wiley in Applied Organometallic Chemistry
- Vol. 39 (2) , e7799
Facile Synthesis of Silver‐Exchanged Phosphotungstic Acid Immobilized on Sn‐Bi Bimetallic Metal–Organic Frameworks for Enhanced Esterification
Metal–organic frameworks (MOFs) are ideal supports for the synthesis of porous composite catalysts. In the present study, Sn‐Bi bimetallic metal–organic frameworks (Sn‐Bi‐MOFs) supported silver‐doped phosphotungstic acid (AgPW) catalysts (AgPW@Sn‐Bi‐BDC and AgPW@Sn‐Bi‐BDC (NH 2 )) were successfully synthesized via a simple in situ impregnation method, which was subsequently applied to catalyze esterification for the production of biodiesel from oleic acid (OA). The physico‐chemical properties of the prepared composite catalysts underwent comprehensive analysis through XRD, FTIR, N 2 physisorption, SEM, EDX, NH 3 ‐TPD, Py‐FTIR, TG, and XPS techniques, confirming the successful impregnation of AgPW on the Sn‐Bi‐MOFs framework. Among the catalysts tested, AgPW@Sn‐Bi‐BDC (NH 2 ) exhibited the better catalytic activity than that of Sn‐Bi‐BDC, Sn‐Bi‐BDC (NH 2 ), and AgPW@Sn‐Bi‐BDC, reaching 91.6% of OA conversion with the methanol:OA molar ratio of 20:1 and the catalyst quantity of 0.2 g at 130°C for 4 h. The high activity of AgPW@Sn‐Bi‐BDC (NH 2 ) is attributed to the available multiscale pore structure, high acidity, and the synergistic action of the Brønsted and Lewis acidic sites. Additionally, the esterification with AgPW@Sn‐Bi‐BDC (NH 2 ) followed the first‐order reaction kinetic model, with an E a of 34.5 kJ/mol. Moreover, the recyclability of the composites was also assessed, demonstrating sustained catalytic activity after four reuses. This approach showed a potential for sustainable and efficient energy production through bimetallic MOFs‐based composite catalysts.
- 1 October 2024
- Published by Wiley in Applied Organometallic Chemistry
- Vol. 39 (2) , e7799
Facile Synthesis of Silver‐Exchanged Phosphotungstic Acid Immobilized on Sn‐Bi Bimetallic Metal–Organic Frameworks for Enhanced Esterification
Metal–organic frameworks (MOFs) are ideal supports for the synthesis of porous composite catalysts. In the present study, Sn‐Bi bimetallic metal–organic frameworks (Sn‐Bi‐MOFs) supported silver‐doped phosphotungstic acid (AgPW) catalysts (AgPW@Sn‐Bi‐BDC and AgPW@Sn‐Bi‐BDC (NH 2 )) were successfully synthesized via a simple in situ impregnation method, which was subsequently applied to catalyze esterification for the production of biodiesel from oleic acid (OA). The physico‐chemical properties of the prepared composite catalysts underwent comprehensive analysis through XRD, FTIR, N 2 physisorption, SEM, EDX, NH 3 ‐TPD, Py‐FTIR, TG, and XPS techniques, confirming the successful impregnation of AgPW on the Sn‐Bi‐MOFs framework. Among the catalysts tested, AgPW@Sn‐Bi‐BDC (NH 2 ) exhibited the better catalytic activity than that of Sn‐Bi‐BDC, Sn‐Bi‐BDC (NH 2 ), and AgPW@Sn‐Bi‐BDC, reaching 91.6% of OA conversion with the methanol:OA molar ratio of 20:1 and the catalyst quantity of 0.2 g at 130°C for 4 h. The high activity of AgPW@Sn‐Bi‐BDC (NH 2 ) is attributed to the available multiscale pore structure, high acidity, and the synergistic action of the Brønsted and Lewis acidic sites. Additionally, the esterification with AgPW@Sn‐Bi‐BDC (NH 2 ) followed the first‐order reaction kinetic model, with an E a of 34.5 kJ/mol. Moreover, the recyclability of the composites was also assessed, demonstrating sustained catalytic activity after four reuses. This approach showed a potential for sustainable and efficient energy production through bimetallic MOFs‐based composite catalysts.