Dawei Dong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dawei Dong has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Junchao Zhuo
School of Mechanical Engineering, Southwest Jiaotong University, Chengdu, China
2 shared publications - Weiqun Liu
School of Mechanical Engineering, Southwest Jiaotong University, Chengdu, China
2 shared publications - Yan Huang
School of Mechanical Engineering, Southwest Jiaotong University, Chengdu, P. R. China
2 shared publications - Bing Yan
School of Mechanical Engineering, Southwest Jiaotong University, Chengdu, P. R. China
1 shared publication - Chunrong Hua
Southwest Jiaotong University
1 shared publication - Imdad Ullah Khan
Southwest Jiaotong University
1 shared publication
Latest Publications
- 3 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. PP (02780046) , 1-10
Self-Adaptive Energy-Autonomous Integrated System for Full-Wave Acceleration Measurement with Single Multifunction Transducer
Self-power sensors provide an effective solution of long-term monitoring for many applications. An obstacle in the path is the common mismatching of the harvested power and the required power since the harvester and the sensor are independently designed without cooperative consideration. This article proposes an energy-autonomous integrated system (EAIS) designed to wirelessly acquire and transmit vibration signals without the need for an external power source. The system employs a piezoelectric cantilever that both harvests energy and senses acceleration, integrating two circuit subsystems: the energy harvesting subsystem and the acceleration sensing subsystem. A self-adaptive time-division multiplexing strategy is adopted for the two subsystems so that they can work alternatively in an energy-self-sufficient way. By utilization of a smart and dedicated circuit design, the acceleration sensing subsystem is capable of acquiring full-wave acceleration signals with complicated frequency components, which is considered as a great advancement in self-powered sensing studies. In particular, the entire system is fully energy-autonomous with the capability of self-starting, self-powering and self-sensing.
- 3 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. PP (02780046) , 1-10
Self-Adaptive Energy-Autonomous Integrated System for Full-Wave Acceleration Measurement with Single Multifunction Transducer
Self-power sensors provide an effective solution of long-term monitoring for many applications. An obstacle in the path is the common mismatching of the harvested power and the required power since the harvester and the sensor are independently designed without cooperative consideration. This article proposes an energy-autonomous integrated system (EAIS) designed to wirelessly acquire and transmit vibration signals without the need for an external power source. The system employs a piezoelectric cantilever that both harvests energy and senses acceleration, integrating two circuit subsystems: the energy harvesting subsystem and the acceleration sensing subsystem. A self-adaptive time-division multiplexing strategy is adopted for the two subsystems so that they can work alternatively in an energy-self-sufficient way. By utilization of a smart and dedicated circuit design, the acceleration sensing subsystem is capable of acquiring full-wave acceleration signals with complicated frequency components, which is considered as a great advancement in self-powered sensing studies. In particular, the entire system is fully energy-autonomous with the capability of self-starting, self-powering and self-sensing.
- 24 March 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 26 (09)
Modal Testing Method for Whole-Body Vibration of Large-Mass Power Equipment
Modal testing, as a method of artificially applying excitation to obtain structural parameters, is widely acknowledged for its reliability and convenience compared to computer simulation analysis, and has found extensive application. However, a challenging category of test objects in modal testing includes large-mass power systems (such as those exceeding 10[ ]tons), where conducting whole-body modal tests remains problematic. This paper proposes an electromagnetic excitation system equipped with both step excitation modes and mechanical amplification devices. Different lever ratios can be selected according to the requirements of different test scenarios to serve as excitation devices for modal testing. In response to the issues of closely spaced modes and random noise encountered in modal testing using step excitation, a method called Sequential Modal Separation is proposed to reduce modal density. This approach involves first removing noise from response signals, followed by applying a variable inverse decay exponent technique to sequentially separate the modal response signals according to their damping ratios from smallest to largest. Finally, the Hilbert–Huang Transform (HHT) is employed to identify natural frequencies and damping ratios of each separated single-mode response signal. Moreover, addressing the issue where modal tests typically describe vibration characteristics using relative amplitudes at various measurement points, a quantitative analysis method for the amplitudes of each degree-of-freedom (DOF) of the vibration system is proposed, based on a solution set of 6-DOF amplitude and the least squares optimization. The proposed methods were validated through whole-body vibration modal experiments on a 14.8-ton internal combustion powertrain equipped with rubber isolators, demonstrating the superiority of these methods. The approach presented in this paper is suitable for modal testing of large-mass power equipment.
- 24 March 2025
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 26 (09)
Modal Testing Method for Whole-Body Vibration of Large-Mass Power Equipment
Modal testing, as a method of artificially applying excitation to obtain structural parameters, is widely acknowledged for its reliability and convenience compared to computer simulation analysis, and has found extensive application. However, a challenging category of test objects in modal testing includes large-mass power systems (such as those exceeding 10[ ]tons), where conducting whole-body modal tests remains problematic. This paper proposes an electromagnetic excitation system equipped with both step excitation modes and mechanical amplification devices. Different lever ratios can be selected according to the requirements of different test scenarios to serve as excitation devices for modal testing. In response to the issues of closely spaced modes and random noise encountered in modal testing using step excitation, a method called Sequential Modal Separation is proposed to reduce modal density. This approach involves first removing noise from response signals, followed by applying a variable inverse decay exponent technique to sequentially separate the modal response signals according to their damping ratios from smallest to largest. Finally, the Hilbert–Huang Transform (HHT) is employed to identify natural frequencies and damping ratios of each separated single-mode response signal. Moreover, addressing the issue where modal tests typically describe vibration characteristics using relative amplitudes at various measurement points, a quantitative analysis method for the amplitudes of each degree-of-freedom (DOF) of the vibration system is proposed, based on a solution set of 6-DOF amplitude and the least squares optimization. The proposed methods were validated through whole-body vibration modal experiments on a 14.8-ton internal combustion powertrain equipped with rubber isolators, demonstrating the superiority of these methods. The approach presented in this paper is suitable for modal testing of large-mass power equipment.
- Open Access
- 1 January 2025
- Published by Wiley in International Journal of Energy Research
- Vol. 2025 (1)
Combined Crank‐Slider and Rack‐Gear Structures for Energy Harvesting and Impact Reduction of the Car Door
Harvesting energy from the door closing process provides a promising solution for powering wireless sensors in intelligent transport systems, however issues, such as low conversion efficiency and operational resistance hinder its practical application. In this study, an energy harvesting system (EHS) is proposed and its basic and optimized designs are compared and analyzed. The system integrates a crank‐slider mechanism, a rack‐and‐pinion transmission and a flywheel energy storage module: the crank‐slider converts the rotational motion of the door into linear motion, the rack‐and‐pinion gears are engaged only at preset positions to minimize operating resistance, and the flywheel captures the kinetic energy quickly during the door closing process. The key parameters (crank length: 19.8–25.8 cm; connecting rod length: 25–31 cm; engagement angle: 26°–44°; flywheel inertia: 0–102.6 kg‐mm 2 ) were optimized through orthogonal experiments. The results show that the flexible design improves the energy output by 13% compared with the rigid design (35.96–73.79 mJ/time for 1–6 J input), and the orthogonal analysis shows that the eigenvalues of the parameters are distributed in a balanced way, which verifies the feasibility of eliminating the impact kinetic energy loss through elastic contact. In addition, the flexible design reduces the door closing noise by 3–12 dB. Experimental validation shows that the system is capable of providing minute‐level continuous power supply for low‐power sensors.
- 1 January 2025
- Published by Wiley in International Journal of Energy Research
- Vol. 2025 (1)
Open AccessCombined Crank‐Slider and Rack‐Gear Structures for Energy Harvesting and Impact Reduction of the Car Door
Harvesting energy from the door closing process provides a promising solution for powering wireless sensors in intelligent transport systems, however issues, such as low conversion efficiency and operational resistance hinder its practical application. In this study, an energy harvesting system (EHS) is proposed and its basic and optimized designs are compared and analyzed. The system integrates a crank‐slider mechanism, a rack‐and‐pinion transmission and a flywheel energy storage module: the crank‐slider converts the rotational motion of the door into linear motion, the rack‐and‐pinion gears are engaged only at preset positions to minimize operating resistance, and the flywheel captures the kinetic energy quickly during the door closing process. The key parameters (crank length: 19.8–25.8 cm; connecting rod length: 25–31 cm; engagement angle: 26°–44°; flywheel inertia: 0–102.6 kg‐mm 2 ) were optimized through orthogonal experiments. The results show that the flexible design improves the energy output by 13% compared with the rigid design (35.96–73.79 mJ/time for 1–6 J input), and the orthogonal analysis shows that the eigenvalues of the parameters are distributed in a balanced way, which verifies the feasibility of eliminating the impact kinetic energy loss through elastic contact. In addition, the flexible design reduces the door closing noise by 3–12 dB. Experimental validation shows that the system is capable of providing minute‐level continuous power supply for low‐power sensors.
- Open Access
- 2 October 2024
- Published by IOS Press
- p. 176-183
Analysis of Temperature Field Characteristics for Automobile Alternator with Twisted Blades
The characteristics of temperature distribution of an automobile alternator with torsional blades are analyzed in this paper. Firstly, the experimental test rig and the numerical model are established. The consistency between experiment data and simulation results is verified. Then, the effects of the torsion angles on temperature characteristics are explored and their mechanisms are revealed through fluid flow and heat dissipation analysis. The results show that the twisting of the rear fan blades can improve the heat dissipation performance, and when the torsion angle is positive the heat dissipation performance of the alternator is greatly improved with an increasing mass flow rates.
- 2 October 2024
- Published by IOS Press
- p. 176-183
Open AccessAnalysis of Temperature Field Characteristics for Automobile Alternator with Twisted Blades
The characteristics of temperature distribution of an automobile alternator with torsional blades are analyzed in this paper. Firstly, the experimental test rig and the numerical model are established. The consistency between experiment data and simulation results is verified. Then, the effects of the torsion angles on temperature characteristics are explored and their mechanisms are revealed through fluid flow and heat dissipation analysis. The results show that the twisting of the rear fan blades can improve the heat dissipation performance, and when the torsion angle is positive the heat dissipation performance of the alternator is greatly improved with an increasing mass flow rates.