YLYan Li

Yan Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yan Li has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Bearing Fault Diagnosis Method Using Improved Feature Mode Decomposition Based on Spectral Structure Information Detector

    by Zhanyang Yu, Yongteng Jing, Zhipeng Guo, Mingzhi Liu, Yan Li

    Feature Mode Decomposition (FMD) is effective for extracting impulsive fault features, but its random filter initialization may cause fault-induced resonance components to deviate from the filter center or fall into transition bands, leading to feature attenuation. To address this limitation, a center-frequency-guided and bandwidth-constrained Modified Feature Mode Decomposition (MFMD) method is proposed. First, a Spectral Structure Information Detector (SSID) is constructed to localize fault-sensitive center frequencies through a band-limited variational detector and a sparsity-based criterion. Then, a cumulative-energy-guided strategy is introduced to determine the corresponding filter layout range, and the Newton–Raphson-Based Optimizer (NRBO) is employed to adaptively select the cumulative-energy threshold. In this way, the proposed method replaces random frequency-band partition with a fault-sensitive filter-layout scheme. Simulation results show that the mean center-frequency error is reduced from 216 Hz to 14 Hz, while the impulsive-energy coverage is increased from 53.48% to 97.46%. Comparisons with NRBO-FMD, NRBO-VMD, IFMD, and SIVMD demonstrate that NRBO-MFMD provides clearer compound-fault mode extraction under strong interference. For the measured wind-turbine vibration signals, the results from 50 randomly selected samples show that NRBO-MFMD achieves the highest fault-characteristic energy ratio (FCER) and spectral envelope autocorrelation index (SEAI) values for both the 162 Hz and 106 Hz fault features. The results indicate that the proposed method improves fault-sensitive mode extraction under both simulated and real operating conditions, while SEAI is used only as a supplementary assessment indicator.

  • A Methodology to Evaluate the Radial Bending Stress of Transformer Inner Windings Based on the Turn-to-Turn Model

    by Xiongbo Wang, Yan Li, Zhanyang Yu, Peng Li, Zhengyu Xu

    The considerable size and intricacy of high-power transformers frequently lead to inefficiency in finite element simulation analysis. To promptly and accurately estimate the stress state of the winding, this paper presents a theoretical approach to analyze the bending stress for each conductor in the inner winding of the transformer. Firstly, this approach takes into account the influences of conductor leakage flux and radial force as they vary with the radial position of the conductor. Subsequently, a 40000 kVA/110 kV transformer is adopted as a prototype, and the turn-to-turn winding model is constructed. The proposed analytical model is verified using 3D finite element method (FEM) simulations. Finally, a leakage flux test was conducted on the prototype, and the simulation and experimental results confirmed the validity of the proposed method.


  • Analysis Method of Transformer Fatigue Life and Damage Under Multiple Short-Circuit Conditions

    by Xiongbo Wang, Yan Li, Zhanyang Yu, Yuxin Miao, Peng Li, Zhengyu Xu

    Transformer winding subjected to alternating stresses caused by multiple short circuits can fail by fatigue even though the stress is below the yield point. The effect of the mean stress of unidirectional impulse pulsating short-circuit force is not considered in previous studies. Therefore, this paper proposes a general method for assessing the stress fatigue life and damage of transformer winding under short-circuit conditions. Take a 110 kV transformer for an instance, the electromagnetic forces and stresses on the winding under short-circuit conditions were calculated based on electromagnetic-structural coupling. The dynamic measurement of short circuit force is realized by using the piezoelectric thin film polyvinylidene fluoride (PVDF) sensor to verify the accuracy of the simulation calculation. Based on finite element stress results, this paper proposes a five-step method for calculating stress fatigue life, the S - N curve of the copper winding is estimated, and the short-circuit force of the unidirectional impulse is corrected under the consideration of the mean stress effect. Both the fatigue life and damage of transformer winding is analyzed using the Palmgren-Miner model. The proposed methodology can evaluate the number of stress cycles leading to transformer winding failure as well as the weak link of winding fatigue life.


  • Research on the Influence of Uneven Temperature Distribution of Transformer Windings on Short Circuit Strength

    by Yan Li, Tiannan Meng, Ziwei Li, Zhanyang Yu, Xiongbo Wang, Peng Li, Zhengyu Xu

    Whether the hot spot temperature rise exceeds the limit under long-term thermal effects and the impact of temperature rise effect on material parameters has attracted much attention. At the same time, as a key structural component of the transmission and transformation system, the calculation and verification of the winding mechanical strength of transformers during three-phase short circuits is a key factor in analyzing their stability during operation. Given that the previous analysis of the impact of transformer short-circuit strength only considered uniform temperature conditions, it is necessary to compare and analyze the impact of uneven temperature on winding stability. This article focuses on the SGB10-800 transformer prototype, conducting temperature rise experiments and simulation analysis to verify the accuracy of simulation processing. Conduct tests on the changes in force and deformation of wires under different temperature conditions. Finally, analysis of the impact of uneven temperature on the short-circuit strength of transformer windings.