DLDexu Lv

Dexu Lv

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dexu Lv has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Low-Speed Sensorless Control With Fault-Tolerant Ability for SRM Using Unsaturated Inductance Reconstruction and Over-Relaxed Newton Method

    by Dexu Lv, Wen Ding, Shuo Chen, Jun Cai, Zhonggang Yin

    This article proposes a low-speed sensorless control method for switched reluctance motor (SRM) with open-circuit fault tolerance. The scheme estimates the rotor position based on the reconstructed unsaturated inductance and the over-relaxed Newton method. First, the full cycle of the SRM is divided into three regions: conduction, demagnetization, and pulse injection, and the inductance calculation for each case are provided. A dual-level-fitting-based unsaturated inductance reconstruction method is proposed to reconstruct the unsaturated inductance based on the current and saturated inductance. Then, a rotor position estimation scheme using the full-cycle unsaturated inductance and the over-relaxed Newton method is proposed. The scheme takes the sum of the squares of the differences between the reconstructed unsaturated inductances and the Fourier series inductance as the cost function. The over-relaxed Newton method is employed to find the minimum value of this cost function, which yields the rotor position. In addition, the initial position estimation method and the rotor position estimation method for open-circuit faults are given. Eventually, the proposed scheme is verified on a three-phase 12/8 SRM to verify its feasibility and effectiveness. The experimental results show that the scheme can operate stably at low speeds, has self-starting capability, and open-circuit fault tolerance.


  • Adaptive Rotor Position-Error Compensation Scheme for PMSM Sensorless Drives Based on Low-Frequency Sinusoidal Signal Injection

    by Shuo Chen, Xiaoyue Wang, Xiang Wu, Chao Li, Wen Ding, Yongxiang Xu, Jibin Zou, Dexu Lv, Yan Chen

    Model-based sensorless control of permanent magnet synchronous machines (PMSMs) is susceptible to significant position deviations caused by inverter nonlinearity, parameter mismatch and digital delay, which are challenging to compensate for accurately. To address this issue, an adaptive position error compensation scheme based on low-frequency sinusoidal injection is proposed. By injecting a low-frequency sinusoidal signal into the estimated position, disturbance components containing position error information are excited and extracted using proposed signal demodulation method. A cost function is designed based on these disturbance components, and the gradient descent optimization (GDO) method is adopted to minimize it, thereby searching for the optimal compensation value. The proposed scheme can achieve the total position error compensation without requiring accurate knowledge of inverter nonlinearity or motor parameters. The effectiveness of proposed scheme is verified by experimental results.


  • A Computationally-Efficient, Finite-Position-Set Phase-Locked Loop Incorporating Harmonic-Suppression Capability for PMSM Sensorless Drives

    by Shuo Chen, Xiaoyue Wang, Chao Li, Xiang Wu, Xin Dai, Wen Ding, Yongxiang Xu, Jibin Zou, Dexu Lv, Zhixun Ma

    The finite-position-set phase-locked loop (FPS-PLL) has been extensively studied due to its excellent dynamic response, but its high computational burden and insufficient steady-state accuracy need to be further overcome. To address these limitations, a computationally-efficient FPS-PLL incorporating harmonic-suppression capability is proposed for permanent magnet synchronous motor (PMSM) sensorless drives. Firstly, the mechanisms and drawbacks of conventional PLL and existing FPS-PLLs are analyzed. Afterwards, to address the FPS-PLL's susceptibility to direct current (DC) and harmonic interference, a novel cost function incorporating harmonic-suppression capability based on a modified integral segment is designed to improve the interference immunity. Subsequently, a simple initial sector boundary setting scheme based on the novel cost function is presented, providing the initial iteration value that satisfies the local convergence criteria and is close to the actual position. Further, the Newton iteration process is executed twice to obtain the accurate rotor position information, thereby achieving the low computational burden. A linear tracking differentiator-based speed observer is designed to extract the rotor speed, avoiding the noise amplification associated with a direct differential operator. Finally, the validity of the proposed FPS-PLL estimator is verified by experimental results.


  • Sensorless Control Scheme for SRM Drives Using Newton–Raphson Method-Based Finite Position Set-Phase-Locked Loop

    by Dexu Lv, Wen Ding, Shuo Chen, Jun Cai, Zhonggang Yin

    This paper proposes a sensorless control of switched reluctance motor (SRM) based on quadrature feature position observer (QFPO) and finite position set-phase locked loop (FPS-PLL) over medium- and high-speed range. The feature-flux-linkage-based method is adopted to compare the real-time flux linkage with the feature-position flux linkage to obtain the feature position of the SRM. Then, the QFPO is used to extract the fundamental frequency and its quadrature signal of the feature position for rotor position estimation. To improve the performance of sensorless control, FPS-PLL is used for rotor position estimation. Through the designed iterative formula of Newton-Raphson method, only two iterations are needed to obtain the accurate rotor position. Meanwhile, the convergence within the calculation domain is proved, and the theoretical iterative accuracy is given. This scheme does not require parameter tuning and eliminates the need for a proportional-integral controller with a fixed gain in the quadrature phase locked loop. To verify the feasibility of the proposed scheme, experiments are conducted on the 750W 12/8 SRM. The experimental results show that the proposed scheme can improve the observation performance of the sensorless control scheme, increase the operating range of the motor, and has better robustness.


  • A Novel Computationally Efficient Finite Position Set-Phase Locked Loop for Low-Speed Sensorless IPMSM Control

    by Shuo Chen, Xindong Yu, Xiang Wu, Chao Li, Wen Ding, Yongxiang Xu, Jibin Zou, Dexu Lv, Zhixun Ma

    This letter proposes a novel computationally efficient finite position set-phase locked loop (FPS-PLL) for low-speed sensorless interior permanent magnet synchronous motor control. A novel equivalent position error is designed based on the complex operation of current responses, enabling the derivation of an improved Newton iteration formula. The iteration formula is convergent in the whole computational domain so that the iterative operations about the cost function for the appropriate iterative initial value can be avoided. Only two iterations are required to obtain the finest rotor position, which is less than existing FPS-PLL schemes. The parameter tuning is avoided in the iterative search process for rotor position, and the fast dynamic response is achieved. Moreover, a tracking differentiator-based speed observer is designed to extract the rotor speed without introducing the differentiator. Finally, the effectiveness of the proposed scheme is verified by experimental results.


  • Phase Current Reconstruction Scheme of SRM Drives Based on Interleaved Pulse Injection Using Single DC-Link Current Sensor

    by Dexu Lv, Wen Ding, Shuo Chen, Jun Cai, Zhonggang Yin

    For the control and drive protection of switched reluctance motor (SRM), it is necessary to acquire accurate phase current. A phase current reconstruction method is proposed for the single-current-sensor SRM drive system. Firstly, the operating principles of SRM are analyzed based on the three-phase asymmetric half bridge (AHB) topology. Then, a phase current reconstruction method based on interleaved pulse injection is proposed, which injects interleaved pulses with large duty cycle into the down switch of conduction phase, decouples the dc-link current under different operating states, and reconstructs the phase current. The number of current sensors, the size and cost of the driver are reduced by the proposed method. Moreover, it improves the reliability of the system and is appropriate for control modes such as current chopping control (CCC), voltage-pulsewidth modulation (PWM) control and single pulse control (SPC). It does not require additional circuits or change of the converter topology, and can realize current reconstruction of the conduction phase and the idle phase. Finally, combined with the proposed method, the overall control strategy is realized. The effectiveness of the proposed phase current reconstruction method is verified on a 750 W 12/8 SRM.


  • Finite Control Set Model Predictive Torque Control of Switched Reluctance Motor Based on Three-Phase Four-Leg Inverter

    by Dexu Lv, Wen Ding, Yangfan Wang, Kai Wang, Shuo Chen, Jun Cai

    This article proposes a finite control set model predictive torque control (FCS MPTC) scheme based on three-phase four-leg inverter to suppress torque ripple and reduce the sharp current drop at the initial stages of the commutation regions. First, the operating modes of three-phase four-leg topology are analyzed, and the sectors are divided according to the operation of switched reluctance motor (SRM) on this topology. Then, predictive models for the current and torque in the single-phase conduction regions are derived using Le-Huy model and candidate voltage vectors. The proposed FCS MPTC scheme addresses the difficulty in predicting phase voltage during commutation regions by using the characteristic of equal current of two phases during these stages, achieving full-cycle FCS MPTC. Furthermore, to reduce computational burden while ensuring torque ripple suppression, the switching states are optimized based on the potential operating states. Eventually, experiments are carried out on a three-phase 750 W 12/8 SRM to verify the effectiveness of the proposed scheme. The results demonstrate that the proposed FCS MPTC scheme improves the effect of torque ripple suppression compared to existing schemes.


  • Sensorless Control for Switched Reluctance Motor Based on Quadrature Feature Position Observer at Medium and High Speeds

    by Dexu Lv, Wen Ding, Yangfan Wang, Kai Wang, Shuo Chen, Jun Cai

    The conventional linear prediction has discontinuous estimated speed and position, and the error of flux linkage reduces the estimation accuracy. To solve the above problems, this article proposes a quadrature feature position observer for switched reluctance motor (SRM) at medium and high speeds, which includes harmonic decouple network (HDN), multiple second-order generalized integrator (MSOGI) and quadrature signal generator. This method uses HDN and MSOGI to filter the nonfundamental frequency of the feature position signal. Then a quadrature signal generator to transform the feature position signals into a set of quadrature signals, and the rotor position and speed are estimated by using the phase locked loop. Compared with the linear prediction method, proposed method has higher estimation accuracy, and there are no discontinuous estimated speed and position. In addition, this method does not need to measure the 3-D magnetic characteristics, requires less data storage space, the implementation is simpler, and has a wider application range. Eventually, the effectiveness of this method is verified on the 750 W 12/8 SRM setup, experimental results show that proposed method can improve the steady state and transient performance of sensorless control system.


  • Low-Speed Sensorless Control of Switched Reluctance Motor Drives Using Random Pulse Injection for Noise Reduction

    by Dexu Lv, Wen Ding, Yangfan Wang, Shuo Chen, Jun Cai, Xiang Wu

    To reduce copper loss and noise caused by high-frequency pulse injection (HFPI), this paper proposes a random pulse injection method based on proportional-integral control duty cycle (PI-RPI) for sensorless control of switched reluctance motors (SRM) at low speed. Conventional injection methods use a fixed voltage duty cycle for position estimation, while the induced current in the idle phase varies with the rotor position, which will produce large copper loss. Additionally, fixed-frequency signal injection causes discrete harmonics in the current power spectral density (PSD), which result in extra noise. The above problems reduce the efficiency of the drive system and limit the use of traditional sensorless methods. This paper first introduces the traditional HFPI method. Based on that, the copper loss of the idle phase is reduced by closed-loop control of the induced current using a proportional-integral controller. Then, a novel random pulse injection method using H-bridge topology is proposed, which eliminates discrete harmonics in the current PSD by injecting pulses of random frequency and direction. The current PSD of the proposed PI-RPI method is compared with the conventional methods. The effectiveness of the proposed sensorless control scheme is verified on a 750W SRM setup.