Momina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Momina has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Mohd Rafatullah
Department of Mathematics and Natural Sciences, Prince Mohammad Bin Fahd University, Al-Khobar, Saudi Arabia
2 shared publications Ahmad Kafeel
Jamia Millia Islamia
1 shared publication- Anees Ahmad
Department of Industrial Chemistry, Aligarh Muslim University, Aligarh 202001, UP, India
1 shared publication - Marta Otero
Departamento de Química y Física Aplicadas, Universidad de León, Campus de Vegazana, 24071 León, Spain
1 shared publication - Masoom Raza Siddiqui
Department of Chemistry, College of Science, King Saud University
1 shared publication - Mohammad Mujahid
Department of Physics, Faculty of Science, King Abdulaziz University, Jeddah, Saudi Arabia
1 shared publication
Latest Publications
- 15 December 2024
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 51 (2) , 1063-1092
Enhanced photocatalytic activity, protein interaction and cost analysis studies of Carissa carandas: derived carbon quantum dots
- 15 December 2024
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 51 (2) , 1063-1092
Enhanced photocatalytic activity, protein interaction and cost analysis studies of Carissa carandas: derived carbon quantum dots
- 15 November 2023
- Published by Springer Nature
- p. 71-77
Green Synthesis of Carbon Dot (CDs) and Sensing of Metal Ion
- 15 November 2023
- Published by Springer Nature
- p. 71-77
Green Synthesis of Carbon Dot (CDs) and Sensing of Metal Ion
- Open Access
Removal of Rhodamine B from Water Using a Solvent Impregnated Polymeric Dowex 5WX8 Resin: Statistical Optimization and Batch Adsorption Studies
Herein, commercially available Dowex 5WX8, a cation exchange polymeric resin, was modified through solvent impregnation with t-butyl phosphate (TBP) to produce a solvent impregnated resin (SIR), which was tested for the removal of rhodamine B (RhB) from water in batch adsorption experiments. The effect of SIR dosage, contact time, and pH on RhB adsorption was studied and optimized by response surface methodology (RSM), interaction, Pareto, and surface plots. Scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) were respectively used for characterizing SIR surface morphology and identifying active binding sites before and after RhB adsorption. SEM showed that the pristine SIR surface was covered with irregular size and shape spots with some pores, while RhB saturated SIR surface was non-porous. FTIR revealed the involvement of electrostatic and π–π interactions during RhB adsorption on SIR. Dosage of SIR, contact time, and their interaction significantly affected RhB adsorption on SIR, while pH and its interaction with dosage and contact time did not. The optimum identified experimental conditions were 0.16 g of SIR dose and 27.66 min of contact time, which allowed for 98.45% color removal. Moreover, RhB adsorption equilibrium results fitted the Langmuir isotherm with a maximum monolayer capacity (qmax) of 43.47 mg/g.
Open AccessRemoval of Rhodamine B from Water Using a Solvent Impregnated Polymeric Dowex 5WX8 Resin: Statistical Optimization and Batch Adsorption Studies
Herein, commercially available Dowex 5WX8, a cation exchange polymeric resin, was modified through solvent impregnation with t-butyl phosphate (TBP) to produce a solvent impregnated resin (SIR), which was tested for the removal of rhodamine B (RhB) from water in batch adsorption experiments. The effect of SIR dosage, contact time, and pH on RhB adsorption was studied and optimized by response surface methodology (RSM), interaction, Pareto, and surface plots. Scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) were respectively used for characterizing SIR surface morphology and identifying active binding sites before and after RhB adsorption. SEM showed that the pristine SIR surface was covered with irregular size and shape spots with some pores, while RhB saturated SIR surface was non-porous. FTIR revealed the involvement of electrostatic and π–π interactions during RhB adsorption on SIR. Dosage of SIR, contact time, and their interaction significantly affected RhB adsorption on SIR, while pH and its interaction with dosage and contact time did not. The optimum identified experimental conditions were 0.16 g of SIR dose and 27.66 min of contact time, which allowed for 98.45% color removal. Moreover, RhB adsorption equilibrium results fitted the Langmuir isotherm with a maximum monolayer capacity (qmax) of 43.47 mg/g.
- Open Access
Optimization Study for the Desorption of Methylene Blue Dye from Clay Based Adsorbent Coating
Batch desorption experiments of methylene blue (MB) dye from a clay adsorbent coating were carried out to evaluate the maximum desorption conditions. Combination of thermal and chemical regeneration techniques were used for the desorption process. The desorption of MB was found to be 70% using an HCl solvent after heating adsorbent coating at 160 °C. The optimization study was carried out to identity the optimum desorption conditions using MINITAB 14 software. The individual and interaction effects of three factors, temperature, dye concentration and contact time for desorption of dye were determine by applying response surface methodology (RSM). The optimization results showed that all three factors have main effects whereas the interaction of concentration–time is significant as compared to other interactions. The findings exhibit a maximum desorption efficiency 23 mg/g at 60 °C for 100 mg/L of dye and 150 min of contact time.
Open AccessOptimization Study for the Desorption of Methylene Blue Dye from Clay Based Adsorbent Coating
Batch desorption experiments of methylene blue (MB) dye from a clay adsorbent coating were carried out to evaluate the maximum desorption conditions. Combination of thermal and chemical regeneration techniques were used for the desorption process. The desorption of MB was found to be 70% using an HCl solvent after heating adsorbent coating at 160 °C. The optimization study was carried out to identity the optimum desorption conditions using MINITAB 14 software. The individual and interaction effects of three factors, temperature, dye concentration and contact time for desorption of dye were determine by applying response surface methodology (RSM). The optimization results showed that all three factors have main effects whereas the interaction of concentration–time is significant as compared to other interactions. The findings exhibit a maximum desorption efficiency 23 mg/g at 60 °C for 100 mg/L of dye and 150 min of contact time.