Sakar Pahari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sakar Pahari has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Peter Tarmo Savolainen
Department of Civil and Environmental Engineering, Michigan State University, East Lansing, MI, USA
6 shared publications - Sagar Keshari
Department of Civil and Environmental Engineering, Michigan State University, East Lansing, MI
6 shared publications - Timothy J. Gates
Department of Civil and Environmental Engineering, Michigan State University, East Lansing, MI, USA
6 shared publications John Racine
Department of Civil and Environmental Engineering, Michigan State University, East Lansing, MI
3 shared publications- Magdalena Cavka
Department of Civil and Environmental Engineering, Michigan State University, East Lansing, MI
3 shared publications - Myles W. Overall
Lyles School of Civil and Construction Engineering, Purdue University, West Lafayette, IN 47906, USA
3 shared publications
Latest Publications
- 22 October 2026
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
Effect of Centerlines and Edgelines on Driver Speed Selection and Lane Positioning on a Low-Speed Urban Collector Street
This study investigated the effects of centerline and edgeline presence on driver speed selection and lateral positioning behavior on a low-speed urban collector street. The study was conducted along a two-lane two-way street segment that had been recently reconstructed, which allowed for the centerline and edgeline markings to be installed in separate phases. Cameras were used to record vehicle speed and lateral position data at five locations along the corridor during each striping phase, which included: (1) no striping, (2) centerline only striping, and (3) centerline plus edgeline striping. Linear regression models were developed to assess the impacts of striping configuration and roadway cross-sectional characteristics on speed and lateral position. The absence of any longitudinal striping resulted in speeds that were 0.8 mph lower than when a centerline was present and 2.3 mph lower than when both a centerline and edgeline were present. In terms of lateral position, drivers were positioned closest to the center of the roadway when both the centerline and edgeline were present and shifted approximately 1-ft further to the right when no edgeline was present (with or without a centerline). Furthermore, the combined use of centerlines and edgelines resulted in a more uniform vehicle lane position along the corridor, with reduced lateral variability during roadway width transitions or when vehicles were parked along the curb. Collectively, the findings provide preliminary evidence that the exclusion of longitudinal pavement markings contributes to lower speeds and generally more cautious travel along two-lane, two-way urban collector streets.
- 22 October 2026
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
Effect of Centerlines and Edgelines on Driver Speed Selection and Lane Positioning on a Low-Speed Urban Collector Street
This study investigated the effects of centerline and edgeline presence on driver speed selection and lateral positioning behavior on a low-speed urban collector street. The study was conducted along a two-lane two-way street segment that had been recently reconstructed, which allowed for the centerline and edgeline markings to be installed in separate phases. Cameras were used to record vehicle speed and lateral position data at five locations along the corridor during each striping phase, which included: (1) no striping, (2) centerline only striping, and (3) centerline plus edgeline striping. Linear regression models were developed to assess the impacts of striping configuration and roadway cross-sectional characteristics on speed and lateral position. The absence of any longitudinal striping resulted in speeds that were 0.8 mph lower than when a centerline was present and 2.3 mph lower than when both a centerline and edgeline were present. In terms of lateral position, drivers were positioned closest to the center of the roadway when both the centerline and edgeline were present and shifted approximately 1-ft further to the right when no edgeline was present (with or without a centerline). Furthermore, the combined use of centerlines and edgelines resulted in a more uniform vehicle lane position along the corridor, with reduced lateral variability during roadway width transitions or when vehicles were parked along the curb. Collectively, the findings provide preliminary evidence that the exclusion of longitudinal pavement markings contributes to lower speeds and generally more cautious travel along two-lane, two-way urban collector streets.
- 17 November 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2680 (6) , 569-583
Driver Response to Winter Weather Warning Messages on Changeable Message Signs Approaching Freeway Bridge Overpasses
This study examined the effectiveness of weather warning messages posted on a changeable message sign (CMS) as a speed reduction countermeasure for motorists approaching freeway bridge overpasses during winter weather conditions. Two weather warning messages were tested, including “Bridge Ices Before Road / Reduce Speeds” and “Slippery Road Conditions / Reduce Speeds,” in addition to the default travel time messages. The messages were evaluated through a series of field studies conducted in Michigan at three rural freeway bridge overpasses with a CMS on the approach during the winter seasons of 2023 and 2024. Speed measurements were obtained for each subject vehicle both upstream of the CMS and also at the start of the bridge. The study found that the winter weather warning messages were effective toward reducing the speed of vehicles approaching the bridge overpass during winter weather conditions. The most substantial impacts, in relation to both the speed reduction likelihood and magnitude, were observed when the “Slippery Road Conditions / Reduce Speeds” message was displayed on the CMS. With this message displayed, drivers were twice as likely to reduce their speed before reaching the bridge and the speed reductions were 0.6 to 0.7 mph greater, on average, compared with the default travel time messages. In addition, the strongest speed reduction were observed for the fastest group of drivers, which is the most vulnerable group from a crash severity risk standpoint and, thus, are considered the most highly targeted driver group for speed reductions.
- 17 November 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2680 (6) , 569-583
Driver Response to Winter Weather Warning Messages on Changeable Message Signs Approaching Freeway Bridge Overpasses
This study examined the effectiveness of weather warning messages posted on a changeable message sign (CMS) as a speed reduction countermeasure for motorists approaching freeway bridge overpasses during winter weather conditions. Two weather warning messages were tested, including “Bridge Ices Before Road / Reduce Speeds” and “Slippery Road Conditions / Reduce Speeds,” in addition to the default travel time messages. The messages were evaluated through a series of field studies conducted in Michigan at three rural freeway bridge overpasses with a CMS on the approach during the winter seasons of 2023 and 2024. Speed measurements were obtained for each subject vehicle both upstream of the CMS and also at the start of the bridge. The study found that the winter weather warning messages were effective toward reducing the speed of vehicles approaching the bridge overpass during winter weather conditions. The most substantial impacts, in relation to both the speed reduction likelihood and magnitude, were observed when the “Slippery Road Conditions / Reduce Speeds” message was displayed on the CMS. With this message displayed, drivers were twice as likely to reduce their speed before reaching the bridge and the speed reductions were 0.6 to 0.7 mph greater, on average, compared with the default travel time messages. In addition, the strongest speed reduction were observed for the fastest group of drivers, which is the most vulnerable group from a crash severity risk standpoint and, thus, are considered the most highly targeted driver group for speed reductions.
- 9 November 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2680 (5) , 616-628
Driver Response to a Slippery Curve Warning System during Winter Weather Conditions
This study assessed the effectiveness of a slippery curve warning system (SCWS) as a speed reduction countermeasure during winter weather conditions. A field evaluation was conducted during the winter of 2024 at two horizontal curves located on a rural highway in northern Michigan. The SCWS that existed at each curve included a pair of slippery when wet warning signs and a curve warning sign. Each SCWS sign included a series of LEDs along the border that flash during potentially slippery pavement surface conditions and are activated based on current weather and road surface data collected from onsite sensors. The evaluation was conducted during consistent daytime weather conditions that included temperatures in the upper 20°F to low 30°F and wet pavement surfaces. The flashing LED sign borders were manually activated and deactivated every 30 min during data collection periods. Light detection and ranging was utilized to track the speeds of free-flowing vehicles beginning upstream of the SCWS and continuing into the curve. The results showed that the SCWS had a significant speed reduction effect for drivers approaching the curve during winter weather conditions. With the LED sign borders flashing, on entering the curve, drivers were 65% less likely to exceed the curve advisory speed and average speeds were 0.9 to 1.5 mph lower compared with when the LED borders were not flashing. In addition, the speed reduction effect of the flashing LED borders was greatest for the fastest group of drivers, who are the most vulnerable from a crash severity risk standpoint.
- 9 November 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2680 (5) , 616-628
Driver Response to a Slippery Curve Warning System during Winter Weather Conditions
This study assessed the effectiveness of a slippery curve warning system (SCWS) as a speed reduction countermeasure during winter weather conditions. A field evaluation was conducted during the winter of 2024 at two horizontal curves located on a rural highway in northern Michigan. The SCWS that existed at each curve included a pair of slippery when wet warning signs and a curve warning sign. Each SCWS sign included a series of LEDs along the border that flash during potentially slippery pavement surface conditions and are activated based on current weather and road surface data collected from onsite sensors. The evaluation was conducted during consistent daytime weather conditions that included temperatures in the upper 20°F to low 30°F and wet pavement surfaces. The flashing LED sign borders were manually activated and deactivated every 30 min during data collection periods. Light detection and ranging was utilized to track the speeds of free-flowing vehicles beginning upstream of the SCWS and continuing into the curve. The results showed that the SCWS had a significant speed reduction effect for drivers approaching the curve during winter weather conditions. With the LED sign borders flashing, on entering the curve, drivers were 65% less likely to exceed the curve advisory speed and average speeds were 0.9 to 1.5 mph lower compared with when the LED borders were not flashing. In addition, the speed reduction effect of the flashing LED borders was greatest for the fastest group of drivers, who are the most vulnerable from a crash severity risk standpoint.
- 3 October 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2680 (1) , 921-933
Evaluating Driver Response to a Speed Feedback Trailer at Median Crossovers Within Freeway Construction Work Zones
A series of field evaluations were performed to assess the speed reduction effects of a speed feedback trailer (SFT) positioned at various locations before and after a median crossover section within a freeway construction work zone. The SFT was evaluated at three positions at the lane closure taper approaching the median crossover: 1) taper start, 2) taper end, and 3) 800 ft beyond the taper end near the initial R2-1a “Where Workers Present 45” speed limit sign. The SFT was also evaluated within the barrier-divided two-way traffic section after the traffic had crossed over the median. Vehicle speeds approaching the SFT were measured at several locations using LiDAR guns. Positioning the SFT slightly beyond the end of a lane closure taper, adjacent to the nearest R2-1a sign resulted in speed reductions that were both greater in magnitude and sustained further into the work zone compared with when the SFT was located at the taper start or taper end. With the SFT in this position, speeds near the start of the median crossover, which was more than half a mile beyond the SFT and nearly a mile beyond the start of the taper, were 1.4 mph lower compared with when no SFT was present. The SFT was similarly effective for reducing speeds of passenger cars when positioned within the crossover section, although heavy truck speeds were unaffected.
- 3 October 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2680 (1) , 921-933
Evaluating Driver Response to a Speed Feedback Trailer at Median Crossovers Within Freeway Construction Work Zones
A series of field evaluations were performed to assess the speed reduction effects of a speed feedback trailer (SFT) positioned at various locations before and after a median crossover section within a freeway construction work zone. The SFT was evaluated at three positions at the lane closure taper approaching the median crossover: 1) taper start, 2) taper end, and 3) 800 ft beyond the taper end near the initial R2-1a “Where Workers Present 45” speed limit sign. The SFT was also evaluated within the barrier-divided two-way traffic section after the traffic had crossed over the median. Vehicle speeds approaching the SFT were measured at several locations using LiDAR guns. Positioning the SFT slightly beyond the end of a lane closure taper, adjacent to the nearest R2-1a sign resulted in speed reductions that were both greater in magnitude and sustained further into the work zone compared with when the SFT was located at the taper start or taper end. With the SFT in this position, speeds near the start of the median crossover, which was more than half a mile beyond the SFT and nearly a mile beyond the start of the taper, were 1.4 mph lower compared with when no SFT was present. The SFT was similarly effective for reducing speeds of passenger cars when positioned within the crossover section, although heavy truck speeds were unaffected.
- 28 September 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2680 (1) , 934-948
Evaluating Driver Response to Speed Feedback Trailers and Digital Speed Limit Signs Positioned Near the Work Area within Freeway Construction Work Zones
A series of field evaluations were conducted within work zone lane closures on rural freeways in Michigan to determine 1) the optimal positioning of a speed feedback trailer (SFT) approaching an active work area, 2) the effectiveness of a digital speed limit (DSL) sign for posting work zone speed limit reductions, and 3) the effectiveness of a speed feedback panel paired with a DSL. Speed trajectories were collected for vehicles traversing each work zone using a series of handheld light detection and ranging (LiDAR) guns operated by a team of technicians seated in unmarked vehicles within each lane closure. The SFT was found to be increasingly more effective at reducing speeds of vehicles approaching and entering the work area as it was positioned closer to the work area. Positioning the SFT 200 ft from the start of the work area, which was determined to be the optimal position, reduced speeds entering the work area by 3.1 mph compared with when the SFT was positioned further upstream. This SFT position helps ensure that motorists receive timely feedback within sight of the work area while providing sufficient deceleration time to maximize speed reductions as drivers enter the work area. The use of a DSL to reduce the work zone speed limit from 60 mph to 45 mph reduced vehicle speeds by 3.7 mph near DSL. Furthermore, activation of the speed feedback panel that was on the same assembly as the DSL reduced vehicle speeds by an additional 1.8 mph.
- 28 September 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2680 (1) , 934-948
Evaluating Driver Response to Speed Feedback Trailers and Digital Speed Limit Signs Positioned Near the Work Area within Freeway Construction Work Zones
A series of field evaluations were conducted within work zone lane closures on rural freeways in Michigan to determine 1) the optimal positioning of a speed feedback trailer (SFT) approaching an active work area, 2) the effectiveness of a digital speed limit (DSL) sign for posting work zone speed limit reductions, and 3) the effectiveness of a speed feedback panel paired with a DSL. Speed trajectories were collected for vehicles traversing each work zone using a series of handheld light detection and ranging (LiDAR) guns operated by a team of technicians seated in unmarked vehicles within each lane closure. The SFT was found to be increasingly more effective at reducing speeds of vehicles approaching and entering the work area as it was positioned closer to the work area. Positioning the SFT 200 ft from the start of the work area, which was determined to be the optimal position, reduced speeds entering the work area by 3.1 mph compared with when the SFT was positioned further upstream. This SFT position helps ensure that motorists receive timely feedback within sight of the work area while providing sufficient deceleration time to maximize speed reductions as drivers enter the work area. The use of a DSL to reduce the work zone speed limit from 60 mph to 45 mph reduced vehicle speeds by 3.7 mph near DSL. Furthermore, activation of the speed feedback panel that was on the same assembly as the DSL reduced vehicle speeds by an additional 1.8 mph.
- 8 October 2024
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2679 (3) , 975-992
Evaluating Driver Response to Bridge Deck Warning Systems During Winter Weather Conditions
Warning signs are often deployed at bridge overpasses during winter to warn motorists of potentially icy surface conditions on the bridge, although the effectiveness of these signs is questionable. One potential improvement to the standard signage methods is the bridge deck warning system (BDWS), which activates a flashing warning sign border or beacon when conditions warrant based on real-time weather and bridge surface data. However, BDWSs have not been broadly implemented in the United States, and consequently, their effectiveness as a safety countermeasure is not well established. To address this knowledge gap, a series of winter field evaluations were performed along three freeway bridge overpasses in Michigan to assess the effectiveness of various BDWS strategies as a speed reduction countermeasure for motorists approaching a potentially icy bridge. The results showed that a BDWS with a flashing light emitting diode (LED) border reduced motorist speeds when encountering a bridge during winter weather conditions compared with the standard “Bridge Ices Before Road” warning sign. The speed reduction effect was consistent between passenger cars and heavy trucks, but was somewhat stronger at night compared with daytime. Greater speed reductions were observed when the BDWS sign was combined with a dynamic speed feedback sign (DSFS) that displayed a “Slow Down” or “Icy Road” message to approaching motorists, with the strongest effects observed when the DSFS message was pulsed between high and low brightness intensities. BDWSs that included only a flashing overhead beacon did not have a significant effect on speeds compared with the standard warning sign.
- 8 October 2024
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2679 (3) , 975-992
Evaluating Driver Response to Bridge Deck Warning Systems During Winter Weather Conditions
Warning signs are often deployed at bridge overpasses during winter to warn motorists of potentially icy surface conditions on the bridge, although the effectiveness of these signs is questionable. One potential improvement to the standard signage methods is the bridge deck warning system (BDWS), which activates a flashing warning sign border or beacon when conditions warrant based on real-time weather and bridge surface data. However, BDWSs have not been broadly implemented in the United States, and consequently, their effectiveness as a safety countermeasure is not well established. To address this knowledge gap, a series of winter field evaluations were performed along three freeway bridge overpasses in Michigan to assess the effectiveness of various BDWS strategies as a speed reduction countermeasure for motorists approaching a potentially icy bridge. The results showed that a BDWS with a flashing light emitting diode (LED) border reduced motorist speeds when encountering a bridge during winter weather conditions compared with the standard “Bridge Ices Before Road” warning sign. The speed reduction effect was consistent between passenger cars and heavy trucks, but was somewhat stronger at night compared with daytime. Greater speed reductions were observed when the BDWS sign was combined with a dynamic speed feedback sign (DSFS) that displayed a “Slow Down” or “Icy Road” message to approaching motorists, with the strongest effects observed when the DSFS message was pulsed between high and low brightness intensities. BDWSs that included only a flashing overhead beacon did not have a significant effect on speeds compared with the standard warning sign.