Diego B. Valim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Diego B. Valim has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Eduardo Bertoni Fonseca
Universidade Estadual de Campinas, Brasil
3 shared publications - Éder Sócrates Najar Lopes
Faculdade de Engenharia Mecânica, Universidade Estadual de Campinas (UNICAMP)
3 shared publications - André Henrique Guimarães Gabriel
Universidade Estadual de Campinas, Brasil
2 shared publications André L. Jardini
1 shared publicationBruno Zluhan
School of Mechanical Engineering, University of Campinas - UNICAMP, Campinas, SP, Brazil; South Eastern Applied Materials Research Center- SEAM, South East Technological University, Waterford, Ireland
1 shared publication- João Pedro Monteiro Cheloni
SENAI CIMATEC University
1 shared publication
Latest Publications
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1) , e20250146
Microstructural Evolution of PBF-LB AlSi10Mg under Different Heat Treatment Conditions
Laser-based powder bed fusion (PBF-LB) of AlSi10Mg alloys faces non-equilibrium solidification, resulting in a microstructure of α-aluminum phase matrix and an interconnected, fibrous α-silicon-rich phase network. The development of heat treatment (HT) routes tailored specifically for PBF-LB parts are essential, as standardized procedures may not yield optimal results. This study investigates the effect of different HTs on the microstructural characteristics and hardness of AlSi10Mg parts. Analyses revealed that the as-built (AB) microstructure exhibited a typical cellular-dendritic solidification structure. The eutectic α-Si-rich network partially degenerated after direct aging (DA) and stress relieving (SR), while solution annealing (SA), and solution annealing + aging HT erased the solidification microstructure, producing α-Si-rich precipitates dispersed within the α-Al matrix. Columnar grains exhibited preferential epitaxial growth along {001} planes in the direction, with no significant changes observed after HTs. The AB sample displayed a hardness of 122 HV, increasing up to 149 HV after DA. Conversely, SR and SA led to a hardness reduction between 61 and 77 HV. While the DA HT maintains the AB microstructural characteristics with a hardness increase, SR and SA HTs modify the solidification microstructure, reducing hardness.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1) , e20250146
Open AccessMicrostructural Evolution of PBF-LB AlSi10Mg under Different Heat Treatment Conditions
Laser-based powder bed fusion (PBF-LB) of AlSi10Mg alloys faces non-equilibrium solidification, resulting in a microstructure of α-aluminum phase matrix and an interconnected, fibrous α-silicon-rich phase network. The development of heat treatment (HT) routes tailored specifically for PBF-LB parts are essential, as standardized procedures may not yield optimal results. This study investigates the effect of different HTs on the microstructural characteristics and hardness of AlSi10Mg parts. Analyses revealed that the as-built (AB) microstructure exhibited a typical cellular-dendritic solidification structure. The eutectic α-Si-rich network partially degenerated after direct aging (DA) and stress relieving (SR), while solution annealing (SA), and solution annealing + aging HT erased the solidification microstructure, producing α-Si-rich precipitates dispersed within the α-Al matrix. Columnar grains exhibited preferential epitaxial growth along {001} planes in the direction, with no significant changes observed after HTs. The AB sample displayed a hardness of 122 HV, increasing up to 149 HV after DA. Conversely, SR and SA led to a hardness reduction between 61 and 77 HV. While the DA HT maintains the AB microstructural characteristics with a hardness increase, SR and SA HTs modify the solidification microstructure, reducing hardness.
- 23 September 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 916
Influence of build orientation and heat treatment on high cycle fatigue of additively manufactured AlSi10Mg
- 23 September 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 916
Influence of build orientation and heat treatment on high cycle fatigue of additively manufactured AlSi10Mg