Tao Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Tao Hu has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Qin Hu
2 shared publicationsZhennan Lin
2 shared publications- Guihao Ran
State Key Laboratory of Dynamic Testing Technology, North University of China, Taiyuan, China
1 shared publication - Kun Huang
North University of China
1 shared publication - Kun Huang
National Demonstration Center for Experimental Measurement Technology and Instrument Education, School of Instrument and Electronics, North University of China 1 , Tai Yuan, Shanxi, China
1 shared publication Shuangquan Ran
1 shared publication
Latest Publications
- 5 November 2025
- Published by Elsevier in Measurement
- Vol. 259
Integrated portable dual-mode multimorphic ferromagnetic metal defect detection device based on diamond NV centers
- 5 November 2025
- Published by Elsevier in Measurement
- Vol. 259
Integrated portable dual-mode multimorphic ferromagnetic metal defect detection device based on diamond NV centers
- 5 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (20) , 33131-33138
An Integrated Noncontact Torque Sensor Based on Diamond NV Centers
High-precision quantum sensing techniques based on diamond nitrogen vacancy (NV) centers have been widely used in many industries. The quantum precision measurement schemes based on NV centers have been continuously reported in recent years. However, there is still a gap in research on non-contact torque measurement applied to common steel shaft materials. Therefore, in this paper, an integrated non-contact torque sensor based on diamond nitrogen vacancy (NV) centers is proposed. The magnetic flux gathering module, microwave (MW) antenna, light path system, fluorescence acquisition module, amplification and filtering circuitry (AAFC), copper coil, and power conversion circuitry were integrated into the torque sensor, with a volume of approximately 33.18 cm 3 . In our work, infinite gain multiple feedback amplification filter circuits had been used to improve the signal quality and magnetic flux aggregation modules to improve the detection sensitivity of the system. The ellipsoidal light gathering cavity was used to enhance the fluorescence utilization. The magnetoelastic effect of ferromagnetic materials had been combined to realize the non-contact trial measurement of ordinary steel shafts (with low magnetostriction coefficient). Subsequently, the noise sensitivity of the torque sensor of about 36.218 nNm/Hz 1/2 was verified. This new torque sensor has a high magnetic spatial sensitivity and can therefore be used for torque detection of bearings in a wide range of ferromagnetic materials with low magnetostrictive coefficients.
- 5 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (20) , 33131-33138
An Integrated Noncontact Torque Sensor Based on Diamond NV Centers
High-precision quantum sensing techniques based on diamond nitrogen vacancy (NV) centers have been widely used in many industries. The quantum precision measurement schemes based on NV centers have been continuously reported in recent years. However, there is still a gap in research on non-contact torque measurement applied to common steel shaft materials. Therefore, in this paper, an integrated non-contact torque sensor based on diamond nitrogen vacancy (NV) centers is proposed. The magnetic flux gathering module, microwave (MW) antenna, light path system, fluorescence acquisition module, amplification and filtering circuitry (AAFC), copper coil, and power conversion circuitry were integrated into the torque sensor, with a volume of approximately 33.18 cm 3 . In our work, infinite gain multiple feedback amplification filter circuits had been used to improve the signal quality and magnetic flux aggregation modules to improve the detection sensitivity of the system. The ellipsoidal light gathering cavity was used to enhance the fluorescence utilization. The magnetoelastic effect of ferromagnetic materials had been combined to realize the non-contact trial measurement of ordinary steel shafts (with low magnetostriction coefficient). Subsequently, the noise sensitivity of the torque sensor of about 36.218 nNm/Hz 1/2 was verified. This new torque sensor has a high magnetic spatial sensitivity and can therefore be used for torque detection of bearings in a wide range of ferromagnetic materials with low magnetostrictive coefficients.