Ruidong Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ruidong Li has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Zhen-Yu Yin
Hong Kong Polytechnic Univ
3 shared publications - Zhi Ding
Department of Civil Engineering, Hangzhou City University, Hangzhou, China
3 shared publications Shao-Heng He
2 shared publications- Shao-Heng He
Department of Civil Engineering, Hangzhou City University, Hangzhou, China
2 shared publications - Chengkai Xu1 shared publication
- Dong Liao
Department of Civil Engineering, Hangzhou City University, Hangzhou, China
1 shared publication
Latest Publications
- 22 August 2026
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 328
A framework integrating microtomography and modeling for multiscale granular mechanics
- 22 August 2026
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 328
A framework integrating microtomography and modeling for multiscale granular mechanics
- Top Cited PapersOpen Access
- 11 May 2026
- Published by Springer Nature in Acta Geotechnica
- Vol. 21 (9) , 5765-5784
Drained deformation and non-coaxiality of granular materials under pure principal stress rotation: role of particle morphology
Understanding the deformation and non-coaxiality behavior of granular materials under pure principal stress rotation (PSR) is a highly challenging topic in soil mechanics. However, there has been limited research investigating the influence of particle morphology on these behaviors. In this study, drained torsional shear tests with PSR stress path were performed on four glass beads with different particle morphologies, under various intermediate principal stress coefficients and stress levels. Microstructural analysis using X-ray CT scanning of dummy cylinder specimens was employed to support the interpretation of the experimental data. Results reveal that as particle shape becomes more irregular, the deformability and shear modulus of granular materials initially increase and then decrease, while non-coaxiality consistently increases. A moderate increase in the shape irregularity leads to an increase in the mean coordination number $$\overline{Z}$$ in particle packing, while a highly irregular particle shape results in a decrease in $$\overline{Z}$$ and a looser fabric, which is detrimental to shear modulus. The contact normal directions in non-spherical materials are more concentrated, exhibiting a stronger initial fabric anisotropy that potentially promotes non-coaxiality. Additionally, the proportion of deviatoric strain that is non-coaxial with deviatoric stress tensor significantly increases as particle shape becomes more irregular.- 11 May 2026
- Published by Springer Nature in Acta Geotechnica
- Vol. 21 (9) , 5765-5784
Top Cited PapersOpen AccessDrained deformation and non-coaxiality of granular materials under pure principal stress rotation: role of particle morphology
Understanding the deformation and non-coaxiality behavior of granular materials under pure principal stress rotation (PSR) is a highly challenging topic in soil mechanics. However, there has been limited research investigating the influence of particle morphology on these behaviors. In this study, drained torsional shear tests with PSR stress path were performed on four glass beads with different particle morphologies, under various intermediate principal stress coefficients and stress levels. Microstructural analysis using X-ray CT scanning of dummy cylinder specimens was employed to support the interpretation of the experimental data. Results reveal that as particle shape becomes more irregular, the deformability and shear modulus of granular materials initially increase and then decrease, while non-coaxiality consistently increases. A moderate increase in the shape irregularity leads to an increase in the mean coordination number $$\overline{Z}$$ in particle packing, while a highly irregular particle shape results in a decrease in $$\overline{Z}$$ and a looser fabric, which is detrimental to shear modulus. The contact normal directions in non-spherical materials are more concentrated, exhibiting a stronger initial fabric anisotropy that potentially promotes non-coaxiality. Additionally, the proportion of deviatoric strain that is non-coaxial with deviatoric stress tensor significantly increases as particle shape becomes more irregular. - 7 July 2025
- Published by Elsevier in Transportation Geotechnics
- Vol. 54
A level-set method-based framework for modeling abrasion of railway ballast
- 7 July 2025
- Published by Elsevier in Transportation Geotechnics
- Vol. 54
A level-set method-based framework for modeling abrasion of railway ballast
- Open Access
- 2 June 2025
- Published by Springer Nature in Acta Geotechnica
- Vol. 20 (9) , 4631-4650
Novel observations for the impact of particle morphology on shear modulus of granular materials
The influence of particle shape on the shear modulus at very small strain (G max) of granular materials remains poorly understood and correlated. Using both micro-CT and bender element tests, this study aims to further systematically investigate this influence by comparing six granular materials with distinct particle shapes. The study included materials with angular and rounded particles, as well as relatively spherical and moderately angular particles, with particle morphological factors assessed using micro-CT. A series of bender element tests was conducted on these materials under various relative densities (D r) and mean effective stresses (p′). Additionally, computed tomography (CT) technique was employed to interpret the role of particle shape on G max from a microstructural perspective. The test results reveal that under the same relative density condition, as the irregularity of particle shape increases, the G max of the materials first increases and then decreases. Angular materials exhibit the lowest G max values, primarily due to their larger void ratio, while the mediumly angular materials display the highest G max values compared to rounded and angular materials. Additionally, it was observed that overall regularity (OR) can be used to describe the significant transitional G max response of granular material in relation to the variations in particle morphology. As OR decreases, the sensitivity of G max to p′ initially decreases and then increases, which was found to be related to the shape-dependent particle mean coordination number ( $$\overline{Z}$$ ). Notably, in materials with an extremely low $$\overline{Z}$$ value, G max exhibits a significantly faster increase with p′. Consequently, based on test data from granular materials with a wide range of particle shapes and transitional G max responses, practical equations for correlating the parameters of G max prediction model with particle morphology were formulated and validated.- 2 June 2025
- Published by Springer Nature in Acta Geotechnica
- Vol. 20 (9) , 4631-4650
Open AccessNovel observations for the impact of particle morphology on shear modulus of granular materials
The influence of particle shape on the shear modulus at very small strain (G max) of granular materials remains poorly understood and correlated. Using both micro-CT and bender element tests, this study aims to further systematically investigate this influence by comparing six granular materials with distinct particle shapes. The study included materials with angular and rounded particles, as well as relatively spherical and moderately angular particles, with particle morphological factors assessed using micro-CT. A series of bender element tests was conducted on these materials under various relative densities (D r) and mean effective stresses (p′). Additionally, computed tomography (CT) technique was employed to interpret the role of particle shape on G max from a microstructural perspective. The test results reveal that under the same relative density condition, as the irregularity of particle shape increases, the G max of the materials first increases and then decreases. Angular materials exhibit the lowest G max values, primarily due to their larger void ratio, while the mediumly angular materials display the highest G max values compared to rounded and angular materials. Additionally, it was observed that overall regularity (OR) can be used to describe the significant transitional G max response of granular material in relation to the variations in particle morphology. As OR decreases, the sensitivity of G max to p′ initially decreases and then increases, which was found to be related to the shape-dependent particle mean coordination number ( $$\overline{Z}$$ ). Notably, in materials with an extremely low $$\overline{Z}$$ value, G max exhibits a significantly faster increase with p′. Consequently, based on test data from granular materials with a wide range of particle shapes and transitional G max responses, practical equations for correlating the parameters of G max prediction model with particle morphology were formulated and validated. - Top Cited Papers
- 10 December 2024
- Published by Elsevier in Applied Soft Computing
- Vol. 169
3D reconstruction of arbitrary granular media utilizing vision foundation model
- 10 December 2024
- Published by Elsevier in Applied Soft Computing
- Vol. 169
Top Cited Papers3D reconstruction of arbitrary granular media utilizing vision foundation model
- Open Access
- 22 October 2024
- Published by MDPI AG in Fractal and Fractional
- Vol. 8 (11) , 614
Fractal Analysis of Particle Size and Morphology in Single-Particle Breakage Based on 3D Images
The accurate modeling of single-particle breakage based on three-dimensional (3D) images is crucial for understanding the particle-level mechanics of granular materials. This study aims to propose a systematic framework incorporating single-particle breakage experiments and numerical simulations based on a novel 3D particle reconstruction technique for fractal analysis of particle size and morphology in single-particle breakage. First, the vision foundation model is used to generate accurate particles from 3D images. The numerical approach is validated by simulating the single-particle breakage test with multiple Fujian sand particles. Then, the breakage processes of reconstructed sand particles under axial compression are numerically modeled. The relationship between 3D fractal dimensions and particle size, particle crushing strength, and morphology is meticulously investigated. Furthermore, the implications of these relationships on the particle breakage processes are thoroughly discussed, shedding light on the underlying mechanisms that govern particle breakage. The framework offers an effective way to investigate the breakage behavior of single sand particles, which will enhance understanding of the mechanism of the whole particle breakage process.
- 22 October 2024
- Published by MDPI AG in Fractal and Fractional
- Vol. 8 (11) , 614
Open AccessFractal Analysis of Particle Size and Morphology in Single-Particle Breakage Based on 3D Images
The accurate modeling of single-particle breakage based on three-dimensional (3D) images is crucial for understanding the particle-level mechanics of granular materials. This study aims to propose a systematic framework incorporating single-particle breakage experiments and numerical simulations based on a novel 3D particle reconstruction technique for fractal analysis of particle size and morphology in single-particle breakage. First, the vision foundation model is used to generate accurate particles from 3D images. The numerical approach is validated by simulating the single-particle breakage test with multiple Fujian sand particles. Then, the breakage processes of reconstructed sand particles under axial compression are numerically modeled. The relationship between 3D fractal dimensions and particle size, particle crushing strength, and morphology is meticulously investigated. Furthermore, the implications of these relationships on the particle breakage processes are thoroughly discussed, shedding light on the underlying mechanisms that govern particle breakage. The framework offers an effective way to investigate the breakage behavior of single sand particles, which will enhance understanding of the mechanism of the whole particle breakage process.