Elias Rodriguez-Segura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Elias Rodriguez-Segura has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Juan José Martínez-Nolasco
Departamento de Ingeniería Mecatrónica, Tecnológico Nacional de México (TecNM), Instituto Tecnológico de Celaya (ITC), Celaya 38010, Guanajuato, Mexico
5 shared publications - Heriberto Rodriguez-Estrada
Departamento de Ingeniería Mecatrónica, Tecnológico Nacional de México/IT de Celaya, Antonio García Cubas 600, Celaya 38010, Mexico
3 shared publications - Víctor Sámano-Ortega
Departamento de Ingeniería Mecatrónica, Tecnológico Nacional de México (TecNM), Instituto Tecnológico de Celaya (ITC), Celaya 38010, Guanajuato, Mexico
3 shared publications - Fany Rodríguez García
Instituto Tecnológico de Celaya
2 shared publications - Jaime Arau
Electronic Engineering Department, Tecnológico Nacional de México—CENIDET, Cuernavaca 62490, Mexico
2 shared publications - Jeziel Vázquez
Ingeniería Mecatrónica, Universidad Politécnica de Querétaro, El Marqués 76240, Querétaro, Mexico
2 shared publications
Latest Publications
- 1 August 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 24 (8) , 795-804
Optimized implementation methodology for HIL FPGA simulations for power converters
- 1 August 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 24 (8) , 795-804
Optimized implementation methodology for HIL FPGA simulations for power converters
- Open Access
- 30 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 22 (11) , 962-970
Low Cost and Optimized FPGA-HIL Real Time Simulation of a Boost Converter Powered by a Photovoltaic Panel
This paper presents the development, analysis and testing of a dynamic model for a boost converter powered by a photovoltaic panel. The mathematical model of the panel is presented and a strategy is proposed to integrate its nonlinear dynamics into the dynamic model of the boost converter. Emphasis is placed on the dynamic behavior, leaving the modeling of the effects of parasitic losses inherent to electronic devices for a future study. A discrete model that is feasible to implement in an FPGA to achieve HIL simulation in real time is shown. An optimized strategy of implementation of nonlinear functions implemented in lookup tables is presented. That strategy allows optimizing the resolution without affecting the calculation latency. A latency analysis of the calculation of the model states is also included where a time of 100ns is established for each simulation step. This latency time is sufficient for real-time simulations. Finally, comparisons of results with a software-based simulator to validates the proposed model are shown.
- 30 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 22 (11) , 962-970
Open AccessLow Cost and Optimized FPGA-HIL Real Time Simulation of a Boost Converter Powered by a Photovoltaic Panel
This paper presents the development, analysis and testing of a dynamic model for a boost converter powered by a photovoltaic panel. The mathematical model of the panel is presented and a strategy is proposed to integrate its nonlinear dynamics into the dynamic model of the boost converter. Emphasis is placed on the dynamic behavior, leaving the modeling of the effects of parasitic losses inherent to electronic devices for a future study. A discrete model that is feasible to implement in an FPGA to achieve HIL simulation in real time is shown. An optimized strategy of implementation of nonlinear functions implemented in lookup tables is presented. That strategy allows optimizing the resolution without affecting the calculation latency. A latency analysis of the calculation of the model states is also included where a time of 100ns is established for each simulation step. This latency time is sufficient for real-time simulations. Finally, comparisons of results with a software-based simulator to validates the proposed model are shown.
- Open Access
- 25 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 22 (11) , 945-951
Bidirectional protection for DC systems based on di/dt behavior
The modern electric power systems are going through a revolutionary change due the development of DC loads and higher efficiency of DC systems where DC microgrids have some attractive characteristics, however they have several challenges such as limiting and interrupting fault current. In this paper, a protection for DC systems based on transient di/dt detection is proposed to provide faster short-circuit and overcurrent fault detection, where DC breakers are required to be designed for bidirectional fault current conditions, which is a challenge regarding DC microgrid applications due to some associated problems such as long periods of fault interruption, complex circuit structure, and low reliability. The proposal can detect fault current conditions for different distances from the point of failure, and is suitable to operation in both islanding and grid connected conditions. The proposed circuit was analyzed theoretically and experimentally in steady state, as well as under load changes and short circuit conditions to ensure proper operation, making this solution a suitable fast current fault DC breaker solution, which is a significant advantage and requirement in protection of DC systems.
- 25 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 22 (11) , 945-951
Open AccessBidirectional protection for DC systems based on di/dt behavior
The modern electric power systems are going through a revolutionary change due the development of DC loads and higher efficiency of DC systems where DC microgrids have some attractive characteristics, however they have several challenges such as limiting and interrupting fault current. In this paper, a protection for DC systems based on transient di/dt detection is proposed to provide faster short-circuit and overcurrent fault detection, where DC breakers are required to be designed for bidirectional fault current conditions, which is a challenge regarding DC microgrid applications due to some associated problems such as long periods of fault interruption, complex circuit structure, and low reliability. The proposal can detect fault current conditions for different distances from the point of failure, and is suitable to operation in both islanding and grid connected conditions. The proposed circuit was analyzed theoretically and experimentally in steady state, as well as under load changes and short circuit conditions to ensure proper operation, making this solution a suitable fast current fault DC breaker solution, which is a significant advantage and requirement in protection of DC systems.
- Open Access
Controller Hardware in the Loop Platform for Evaluating Current-Sharing and Hot-Swap in Microgrids
Microgrids have increased in popularity thanks to both the integration of renewable energy resources and their energy distribution capability for remote locations. Moreover, the microgrids, mainly using multiple generators connected in parallel, acquire additional advantages by using both Hot-Swap and Current-Sharing techniques. This paper presents the development of a Hardware in the Loop platform to test Current-Sharing algorithms. It is reinforced that the use of a real-time simulation based on Hardware in the Loop is a viable and cost-effective alternative in the validation of controllers. The platform was developed in a graphical programming environment (LabVIEW 2015) and implemented with NI MyRIO 1900 (National Instruments Corp., Austin, TX, USA) development boards for easier reproducibility. The entire code project is openly available and provided in this paper. A system of photovoltaic energy generators was used to evaluate the performance of the HIL platform. As a result, the platform was able to reproduce a similar behavior to the photovoltaic generator, presenting average mean errors of 0.4 V and 0.2 A in its voltage and current, respectively. Additionally, the platform showed its capability to test Current-Sharing algorithms in the occurrence of Hot-Swap events. This work contributes with a validation tool for energy management systems applied to microgrids.
Open AccessController Hardware in the Loop Platform for Evaluating Current-Sharing and Hot-Swap in Microgrids
Microgrids have increased in popularity thanks to both the integration of renewable energy resources and their energy distribution capability for remote locations. Moreover, the microgrids, mainly using multiple generators connected in parallel, acquire additional advantages by using both Hot-Swap and Current-Sharing techniques. This paper presents the development of a Hardware in the Loop platform to test Current-Sharing algorithms. It is reinforced that the use of a real-time simulation based on Hardware in the Loop is a viable and cost-effective alternative in the validation of controllers. The platform was developed in a graphical programming environment (LabVIEW 2015) and implemented with NI MyRIO 1900 (National Instruments Corp., Austin, TX, USA) development boards for easier reproducibility. The entire code project is openly available and provided in this paper. A system of photovoltaic energy generators was used to evaluate the performance of the HIL platform. As a result, the platform was able to reproduce a similar behavior to the photovoltaic generator, presenting average mean errors of 0.4 V and 0.2 A in its voltage and current, respectively. Additionally, the platform showed its capability to test Current-Sharing algorithms in the occurrence of Hot-Swap events. This work contributes with a validation tool for energy management systems applied to microgrids.
- Open Access
- 13 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2405
Novel Multibus Multivoltage Concept for DC-Microgrids in Buildings: Modeling, Design and Local Control
In this paper, a novel microgrid (MG) concept suitable for direct current (DC) multibus architectures is depicted. Multibus feature is improved in order to distribute power in DC using a number of buses at different voltage level. A teachers offices building that houses several kinds of loads, including a charging station for electric vehicles (EV), is considered to validate the strategy. Several topologies of power electronics converters (PECs) are included in the system to perform specific tasks and providing isolation between bus and final loads. In order to develop the PECs, first, a switching function is used to obtain average model of each converter. Then, converters design is done by using well known methods that allow to obtain parameter values of all the devices in every version of each kind of converter. A hierarchical control is selected to govern the direct current microgrid (DCMG). At a lower control level, local control stage is implemented and tuned using models and designs obtained, with linear controllers in some PECs and classic strategies in others. In higher control level, there is a supervisory strategy that prioritizes the use of generated power to supply the building’s loads. This energy management system (EMS) is based in Petri net theory; it consists of a start-up test, then source condition synchronous algorithm and load condition synchronous algorithm operate the DCMG according to the mentioned priority. Finally, PECs are tested on standalone, performing in closed loop, facing load changes to verify the adequate operation. Some trajectories of a simplified version of the CDMG are tested with local control in order to validate the multibus multivoltage concept. In order to verify coordinated control, some events managed by EMS are presented.
- 13 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2405
Open AccessNovel Multibus Multivoltage Concept for DC-Microgrids in Buildings: Modeling, Design and Local Control
In this paper, a novel microgrid (MG) concept suitable for direct current (DC) multibus architectures is depicted. Multibus feature is improved in order to distribute power in DC using a number of buses at different voltage level. A teachers offices building that houses several kinds of loads, including a charging station for electric vehicles (EV), is considered to validate the strategy. Several topologies of power electronics converters (PECs) are included in the system to perform specific tasks and providing isolation between bus and final loads. In order to develop the PECs, first, a switching function is used to obtain average model of each converter. Then, converters design is done by using well known methods that allow to obtain parameter values of all the devices in every version of each kind of converter. A hierarchical control is selected to govern the direct current microgrid (DCMG). At a lower control level, local control stage is implemented and tuned using models and designs obtained, with linear controllers in some PECs and classic strategies in others. In higher control level, there is a supervisory strategy that prioritizes the use of generated power to supply the building’s loads. This energy management system (EMS) is based in Petri net theory; it consists of a start-up test, then source condition synchronous algorithm and load condition synchronous algorithm operate the DCMG according to the mentioned priority. Finally, PECs are tested on standalone, performing in closed loop, facing load changes to verify the adequate operation. Some trajectories of a simplified version of the CDMG are tested with local control in order to validate the multibus multivoltage concept. In order to verify coordinated control, some events managed by EMS are presented.
- Open Access
- 7 October 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (19) , 9295
Power Sharing Control in a Grid-Tied DC Microgrid: Controller Hardware in the Loop Validation
This article presents the development of a low-cost control hardware in the loop platform for the validation and analysis of controllers used for the management of power sharing between the main grid and a DC microgrid. The platform is made up of two parts: a main grid interconnection system emulator (MGISE) and a controller under test (CUT). The MGISE operates on a 260 V DC bus and includes a 1000 W photovoltaic array, a DC variable load and a single H full bridge converter (HFBC). The CUT includes a phase locked loop and a main cascade control structure composed of two PI controllers. Both the MGISE and the CUT were embedded on an NI myRIO-1900 development board and programmed using LabVIEW virtual instrumentation software. These devices communicate with each other using analog signals representing the AC side current, the DC side voltage, and the HFBC control signal. The MGISE operates with an integration time of 6 µs and its performance is validated by comparing it with a simulation in PSIM. The integration time of the MGISE, the development boards used, as well as its programming environment, and the results obtained from the comparison with PSIM simulation, show that the proposed platform is useful for the validation of controllers for power sharing, with a simple implementation process compared to other hardware description methods and with a low-cost platform.
- 7 October 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (19) , 9295
Open AccessPower Sharing Control in a Grid-Tied DC Microgrid: Controller Hardware in the Loop Validation
This article presents the development of a low-cost control hardware in the loop platform for the validation and analysis of controllers used for the management of power sharing between the main grid and a DC microgrid. The platform is made up of two parts: a main grid interconnection system emulator (MGISE) and a controller under test (CUT). The MGISE operates on a 260 V DC bus and includes a 1000 W photovoltaic array, a DC variable load and a single H full bridge converter (HFBC). The CUT includes a phase locked loop and a main cascade control structure composed of two PI controllers. Both the MGISE and the CUT were embedded on an NI myRIO-1900 development board and programmed using LabVIEW virtual instrumentation software. These devices communicate with each other using analog signals representing the AC side current, the DC side voltage, and the HFBC control signal. The MGISE operates with an integration time of 6 µs and its performance is validated by comparing it with a simulation in PSIM. The integration time of the MGISE, the development boards used, as well as its programming environment, and the results obtained from the comparison with PSIM simulation, show that the proposed platform is useful for the validation of controllers for power sharing, with a simple implementation process compared to other hardware description methods and with a low-cost platform.
- Open Access
- 23 August 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (16) , 9466
A di/dt Detection Circuit for DC Unidirectional Breaker Based on Inductor Transient Behaviour
In this paper, a di/dt detection circuit for DC breaker applications is proposed to provide faster short-circuit and overcurrent fault detection, where DC breakers are required to be designed for unidirectional fault current conditions, which is a challenge regarding DC microgrid applications due to some associated problems such as long periods of fault interruption, complex circuit structure, and low reliability. The proposal, which is based on measurement of di/dt, can detect fault current conditions for different distances from the point of failure, and is suitable to operation in both islanding and grid-connected conditions. The proposed circuit was studied theoretically and experimentally in steady state, as well as under load changes and short circuit conditions to ensure proper operation, making this solution a fast current fault detection solution, which is a significant advantage and requirement in DC microgrid applications.
- 23 August 2021
- Published by MDPI AG in Sustainability
- Vol. 13 (16) , 9466
Open AccessA di/dt Detection Circuit for DC Unidirectional Breaker Based on Inductor Transient Behaviour
In this paper, a di/dt detection circuit for DC breaker applications is proposed to provide faster short-circuit and overcurrent fault detection, where DC breakers are required to be designed for unidirectional fault current conditions, which is a challenge regarding DC microgrid applications due to some associated problems such as long periods of fault interruption, complex circuit structure, and low reliability. The proposal, which is based on measurement of di/dt, can detect fault current conditions for different distances from the point of failure, and is suitable to operation in both islanding and grid-connected conditions. The proposed circuit was studied theoretically and experimentally in steady state, as well as under load changes and short circuit conditions to ensure proper operation, making this solution a fast current fault detection solution, which is a significant advantage and requirement in DC microgrid applications.
- Open Access
- 4 December 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (23) , 8690
Hardware in the Loop Platform for Testing Photovoltaic System Control
The hardware in the loop (HIL) technique allows you to reproduce the behavior of a dynamic system or part of it in real time. This quality makes HIL a useful tool in the controller validation process and is widely used in multiple areas including photovoltaic systems (PVSs). This study presents the development of an HIL system to emulate the behavior of a PVS that includes a photovoltaic panel (PVP) and a DC-DC boost converter connected in series. The emulator was embedded into an NI-myRIO development board that operates with an integration time of 10 µs and reproduces the behavior of the real system with a mean percent error of 2.0478%, compared to simulation results. The implemented emulator is proposed as a platform for the validation of control systems. With it, the experimental stage is carried out on two controllers connected to the PVS without having the real system and allowing to emulate different operating conditions. The first controller is based on the Hill Climbing algorithm for the maximum power point tracking (MPPT), the second is a proportional integral (PI) controller for voltage control. Both controllers generate settling times of less than 3 s; the MPPT controller generates variations in the output in steady state inherent to the algorithm used. For both cases, the comparison of the experimental results with those obtained through software simulation show that the platform fulfills its usefulness when evaluating control systems.
- 4 December 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (23) , 8690
Open AccessHardware in the Loop Platform for Testing Photovoltaic System Control
The hardware in the loop (HIL) technique allows you to reproduce the behavior of a dynamic system or part of it in real time. This quality makes HIL a useful tool in the controller validation process and is widely used in multiple areas including photovoltaic systems (PVSs). This study presents the development of an HIL system to emulate the behavior of a PVS that includes a photovoltaic panel (PVP) and a DC-DC boost converter connected in series. The emulator was embedded into an NI-myRIO development board that operates with an integration time of 10 µs and reproduces the behavior of the real system with a mean percent error of 2.0478%, compared to simulation results. The implemented emulator is proposed as a platform for the validation of control systems. With it, the experimental stage is carried out on two controllers connected to the PVS without having the real system and allowing to emulate different operating conditions. The first controller is based on the Hill Climbing algorithm for the maximum power point tracking (MPPT), the second is a proportional integral (PI) controller for voltage control. Both controllers generate settling times of less than 3 s; the MPPT controller generates variations in the output in steady state inherent to the algorithm used. For both cases, the comparison of the experimental results with those obtained through software simulation show that the platform fulfills its usefulness when evaluating control systems.
- Open Access
- 23 November 2018
- Published by Springer Nature in Journal of Modern Power Systems and Clean Energy
- Vol. 7 (2) , 340-349
Photovoltaic-based DC microgrid with partial shading and fault tolerance
- 23 November 2018
- Published by Springer Nature in Journal of Modern Power Systems and Clean Energy
- Vol. 7 (2) , 340-349
Open AccessPhotovoltaic-based DC microgrid with partial shading and fault tolerance