Jinjin Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jinjin Han has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Kai Ding
8 shared publicationsLinglei Kong
6 shared publicationsWeining Lei
6 shared publicationsBin He
5 shared publicationsQilin Li
5 shared publicationsAqib Mashood Khan
4 shared publications
Latest Publications
- 27 August 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (26) , 51939-51955
Material removal mechanism of SSiC ceramics microgrooves by off-axis waterjet-assisted laser machining
- 27 August 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (26) , 51939-51955
Material removal mechanism of SSiC ceramics microgrooves by off-axis waterjet-assisted laser machining
- 7 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (10) , 14369-14383
Waterjet-laser pretreatment assisted micro-milling of ZrO2: regulating HAZ machinability for large-aspect ratio microgroove fabrication
- 7 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (10) , 14369-14383
Waterjet-laser pretreatment assisted micro-milling of ZrO2: regulating HAZ machinability for large-aspect ratio microgroove fabrication
- 5 November 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (30) , 63802-63815
Investigation of large-aspect ratio Si3N4 microgrooves fabricated by waterjet and laser assisted micro-milling
- 5 November 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (30) , 63802-63815
Investigation of large-aspect ratio Si3N4 microgrooves fabricated by waterjet and laser assisted micro-milling
- Open Access
- 9 August 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 29226
Optimization and performance study of large aspect ratio SiC microgrooves by waterjet assisted laser machining
Silicon carbide (SiC) ceramics hold significant application value in high-end fields such as semiconductors and aerospace due to their exceptional mechanical properties and thermal stability. Large-aspect-ratio (LAR) microgrooves in ceramics are crucial for enabling advanced functionalities in various applications, including microfluidic devices, microelectromechanical systems (MEMS), and thermal management systems, where precise control over fluid flow, structural integrity, and heat dissipation is required. However, their extreme hardness poses challenges for traditional mechanical machining, including low efficiency and severe tool wear, while laser machining is prone to defects such as heat-affected zones and recast layers. This study innovatively employs waterjet-assisted laser micromachining (WJALM), compared to conventional underwater laser micromachining (UWLM), WJALM reduces the recast layer and microcracks through the synergistic cooling and impact effects of the waterjet, while maintaining smaller surface roughness (reduce by 42%). Furthermore, this research systematically optimized the machining parameters for LAR microgrooves through orthogonal experiments and grey-relational analysis (GRA). Results identified an optimal parameter combination is a scanning speed of 800 mm/s, pulse energy of 27 W, and waterjet velocity of 16 m/s, high-quality microgrooves with an aspect-ratio (AR) of 3.66 and an ablation-area-ratio (AAR) of 0.78 can be achieved. This study provides a novel technical solution for the precision machining of hard and brittle materials, offering substantial engineering application value.
- 9 August 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 29226
Open AccessOptimization and performance study of large aspect ratio SiC microgrooves by waterjet assisted laser machining
Silicon carbide (SiC) ceramics hold significant application value in high-end fields such as semiconductors and aerospace due to their exceptional mechanical properties and thermal stability. Large-aspect-ratio (LAR) microgrooves in ceramics are crucial for enabling advanced functionalities in various applications, including microfluidic devices, microelectromechanical systems (MEMS), and thermal management systems, where precise control over fluid flow, structural integrity, and heat dissipation is required. However, their extreme hardness poses challenges for traditional mechanical machining, including low efficiency and severe tool wear, while laser machining is prone to defects such as heat-affected zones and recast layers. This study innovatively employs waterjet-assisted laser micromachining (WJALM), compared to conventional underwater laser micromachining (UWLM), WJALM reduces the recast layer and microcracks through the synergistic cooling and impact effects of the waterjet, while maintaining smaller surface roughness (reduce by 42%). Furthermore, this research systematically optimized the machining parameters for LAR microgrooves through orthogonal experiments and grey-relational analysis (GRA). Results identified an optimal parameter combination is a scanning speed of 800 mm/s, pulse energy of 27 W, and waterjet velocity of 16 m/s, high-quality microgrooves with an aspect-ratio (AR) of 3.66 and an ablation-area-ratio (AAR) of 0.78 can be achieved. This study provides a novel technical solution for the precision machining of hard and brittle materials, offering substantial engineering application value.
- Open Access
- 30 October 2024
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 111, 456-467
Experimental investigation on large-aspect-ratio zirconia ceramic microchannels by waterjet-assisted laser processing
- 30 October 2024
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 111, 456-467
Open AccessExperimental investigation on large-aspect-ratio zirconia ceramic microchannels by waterjet-assisted laser processing
- Open Access
- 16 October 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 4253-4264
Investigation of large-aspect ratio microgrooves on silicon nitride ceramic by WJALM
- 16 October 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 4253-4264
Open AccessInvestigation of large-aspect ratio microgrooves on silicon nitride ceramic by WJALM
- 9 September 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 134 (9-10) , 4127-4140
Investigation on high-aspect-ratio silicon carbide ceramic microchannel by using waterjet-assisted laser micromachining
- 9 September 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 134 (9-10) , 4127-4140
Investigation on high-aspect-ratio silicon carbide ceramic microchannel by using waterjet-assisted laser micromachining
- Open Access
- 27 March 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (4) , 448
Microgrooves with Small Taper Angle Processed by Nanosecond Laser in Closed Flowing Water
To improve the capability of nanosecond lasers to process structures with a high aspect ratio, a new method of nanosecond laser processing in closed flowing water was proposed in this paper. The microgrooves on a stainless steel 304 surface were processed by the new method, and the influence of processing parameters on the microgrooves was studied. The comparative experiments of laser processing in still water and overflowing water were also carried out, and the unusual phenomenon of laser processing in different flowing water was discovered by a high-speed camera. The results showed that the flowing velocity played a crucial role in underwater laser processing, and that high flowing velocity could timely remove bubbles in closed flowing water, thus obtaining higher processing efficiency. As the depth of the groove increased, the bubbles firstly affected the processing of the sidewall, causing a circular transition between the sidewall and bottom surface. The reflection of the laser beam by the bubble could cause secondary processing on the sidewall, resulting in a decrease in the taper angle. Based on the above research, the microgroove with a width of 0.5 mm, aspect ratio of 3, and taper angle of 87.57° was successfully processed by a nanosecond laser in closed flowing water. Compared to conventional nanosecond laser processing, laser processing in closed flowing water was more advantageous in processing microgrooves with a small taper angle and high aspect ratio.
- 27 March 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (4) , 448
Open AccessMicrogrooves with Small Taper Angle Processed by Nanosecond Laser in Closed Flowing Water
To improve the capability of nanosecond lasers to process structures with a high aspect ratio, a new method of nanosecond laser processing in closed flowing water was proposed in this paper. The microgrooves on a stainless steel 304 surface were processed by the new method, and the influence of processing parameters on the microgrooves was studied. The comparative experiments of laser processing in still water and overflowing water were also carried out, and the unusual phenomenon of laser processing in different flowing water was discovered by a high-speed camera. The results showed that the flowing velocity played a crucial role in underwater laser processing, and that high flowing velocity could timely remove bubbles in closed flowing water, thus obtaining higher processing efficiency. As the depth of the groove increased, the bubbles firstly affected the processing of the sidewall, causing a circular transition between the sidewall and bottom surface. The reflection of the laser beam by the bubble could cause secondary processing on the sidewall, resulting in a decrease in the taper angle. Based on the above research, the microgroove with a width of 0.5 mm, aspect ratio of 3, and taper angle of 87.57° was successfully processed by a nanosecond laser in closed flowing water. Compared to conventional nanosecond laser processing, laser processing in closed flowing water was more advantageous in processing microgrooves with a small taper angle and high aspect ratio.