CSChandrasekaran Sasikumar

Chandrasekaran Sasikumar

*This is an algorithmically generated author record based on publicly available information.

Chandrasekaran Sasikumar has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • EXPERIMENTAL AND NUMERICAL INVESTIGATION OF VIBRATION AND DAMPING PROPERTIES OF ALSTONIA MACROPHYLLA FIBER REINFORCED POLYPROPYLENE COMPOSITES: EFFECT OF FIBER CONCENTRATION

    by Harshavardhan Bettegowda, Shettahalli Mantaiah Vinu Kumar, Erusagounder Sakthivelmurugan, Ravichandran Arumugam Thangavel, Chandrasekaran Sasikumar, Santhosh Nagulan

    Many automotive and aerospace industries have shown increasing interest in the manufacture of components from natural fiber composites due to their unique properties, such as low density, low processing cost, biodegradability, recyclability, and tailorable mechanical properties, compared to the synthetic fiber composites. In this context, Alstonia macrophylla (ASM) fiber reinforced polypropylene (ASM/PP) composites were fabricated using the hot-pressing technique. The main focus of this study was to investigate the effect of fiber content on the vibration and damping properties of the ASM/PP composites. ASM fiber was reinforced into PP on volume fraction basis ranging from 0 to 50 vol% in increments of 10 vol%. The resulting composites were designated as Neat PP, A10, A20, A30, A40 and A50 composites, respectively. Free vibration test results revealed that the addition of 40 vol% of ASM fiber into PP enhanced the natural frequency (Mode-I) of the composites. However, at lower fiber content, natural frequency of the ASM/PP composites was reduced due to the softening effect dominated by the PP matrix. Highest damping ratio was exhibited by A30 composites, however beyond 30 vol%, a significant drop in damping ratio was observed. This may be owing to poor agglomeration of the fibers at higher concentration. Experimental results were found to be in good agreement with numerical results obtained from Abaqus simulations, with an error limited to 2.28%. CAE models of the specimens were prepared as per their actual dimension. However, for enhancing effectiveness of the simulation results, the mass of the accelerometer was considered. FESEM analysis on the fractured surface supported the improvement in damping and stiffness properties.

  • INVESTIGATION OF MACHINING BEHAVIOUR OF FLAX REINFORCED EPOXY COMPOSITES USING THE ANN APPROACH

    by Manikandaprabu Nallasivam, Shettahalli Mantaiah Vinu Kumar, Chandrasekaran Sasikumar, Rishi Jayaprakash

    In this study, flax fiber reinforced epoxy (FFRE) composites were fabricated using the hand layup method. The effects of spindle speed (900, 1800, 2700 rpm), feed rate (70, 90, 110 mm/min), and end mill cutters (6, 8, 10 mm) on milling behavior were analyzed. Milling tests were conducted on a vertical CNC machine for a 2 mm constant depth of cut. Experimental details followed Taguchi’s L27 orthogonal array, where cutting force and surface roughness (Ra) were evaluated as output responses. The investigation revealed that cutting force increased with the increase in the feed rate, but decreased as spindle speed was increased. Better surface quality of the milled surface in terms lower cutting force and surface roughness value was achieved at the optimal input conditions. Artificial neural network (ANN) models with different architectures were implemented to predict the cutting force and surface roughness. The analysis showed that predicted values were in close agreement with the experimental results and exhibited a maximum error deviation of ±5%, particularly when 3-5-4-1, and 3-5-4-2 ANN models (Purelin-Purelin-Purelin Transfer function) were employed for single and dual output respectively. The accuracy of the aforesaid models was measured in terms of highest R2 value and lowest mean absolute percentage error (MAPE). Field emission scanning electron microscopy (FESEM) images of the machined surface exposed matrix damage, cavity formation, fiber pull-out, and micro-tear.

  • EVALUATION OF DYNAMIC MECHANICAL PROPERTIES OF FLAX FIBER POLYPROPYLENE (FP) COMPOSITES USING THE ADAPTIVE NEURO FUZZY INFERENCE SYSTEM

    by Shettahalli Mantaiah Vinu Kumar, Ravichandran Arumugam Thangavel, Ranganathan Soundararajan, Chandrasekaran Sasikumar, Erusagounder Sakthivelmurugan, Chinnasamy Nithiyapathi

    Flax fiber reinforced polypropylene (FP) composites were prepared using the compression moulding technique and their dynamic mechanical (DM) properties were studied based on the fiber content. Fiber loading was varied from 0 to 50 vol% with increments of 10 vol% and the samples were designated accordingly as neat PP, FP10, FP20, FP30, FP40, and FP50 composites. The results showed that increased fiber content in the PP matrix improved the DM properties, such as storage modulus (E’), loss modulus (E”), and damping factor (Tanδ). Amongst the fabricated FP laminates, FP40 composites exhibited better viscoelastic performance. Furthermore, the adaptive neuro-fuzzy inference system (ANFIS) was implemented to predict the DM properties, mainly, E’ and E” of the FP composites. The validation of the ANFIS model showed that experimental and predicted results were in good agreement to each other, confirming its reliability in forecasting the DM properties of flax fiber reinforced polypropylene (FP) composites. This study also investigated the thermal degradation behavior of the FP composites using thermogravimetric analysis (TGA). The results showed that thermal stability of the neat PP improved from 432.69 °C to 463.90 °C for optimal fiber loading of 40 vol% flax fiber (FP40). Fractured samples of FP composites were examined using scanning electron microscopy (SEM) to comprehend the interfacial bonding mechanism of the FP composites.


  • IMPACT OF NANOCLAY ON THERMAL, AND STATIC AND DYNAMIC MECHANICAL PROPERTIES OF BAMBOO FIBER REINFORCED UNSATURATED POLYESTER COMPOSITES

    by Benjamin Franklin Selvanayagam, Shettahalli Mantaiah Vinu Kumar, Chandrasekaran Sasikumar, Ravichandran Arumugam Thangavel

    In this article, the effects of nanoclay (NCL) filler on thermal and static and dynamic mechanical properties of bamboo fiber reinforced unsaturated polyester (BP) composites were explored. BP composites were prepared with 20 wt% reinforcement of bamboo fiber, and hybrid NCL filled bamboo fiber reinforced unsaturated polyester (NCBP) were prepared by incorporation of NCL in amounts ranging from 1 to 7 wt% (named as 1NCBP, 3NCBP, 5NCBP and 7NCBP, with reference sample – 0NCBP (BP)), using the hand layup process, followed by curing in a compression moulding machine at constant pressure (20 bar). The fabricated BP and NCBP hybrid composites were tested for static mechanical properties as per ASTM standards. By using a dynamic analyser, viscoelastic properties of the composites, such as storage modulus (E’), loss modulus (E”) and damping factor (Tanδ), were investigated. Results revealed that both static and dynamic mechanical properties of the BP composites increased with an increase in NCL loading. Amongst the nanocomposites, 5NCBP was found superior, however, beyond the optimal amount of 5 wt% NCL, the properties of the materials suffered because of nanoclay agglomeration and poor interfacial bonding between fiber, matrix and filler. The glass transition temperature (Tg) of the BP composite increased from 109.88 °C to 117.73 °C after adding NCL. Thermogravimetric analysis (TGA) results showed that the presence of NCL delayed thermal degradation of the NCBP nanocomposites and thus improved thermal stability. Mechanically fractured samples of NCBP composites were exposed further by field emission scanning microscopy (FESEM) analysis to understand the failure mechanism they endured.


  • EXPERIMENTAL INVESTIGATION ON FREE VIBRATIONAL DAMPING AND DRILLING BEHAVIOR OF FLAX REINFORCED EPOXY COMPOSITES USING ADAPTIVE NEURO FUZZY INFERENCE SYSTEM

    by Shettahalli Mantaiah Vinu Kumar, Rengaraj Jeyakumar, Nallasivam Manikandaprabu, Chandrasekaran Sasikumar

    Flax reinforced epoxy (F-Ep) composites were prepared by the compression moulding technique, varying the fiber content (0, 25, 35 and 45 wt%). The free vibration test was performed on the neat epoxy and F-Ep composites to understand their dynamic characteristics, and results showed that natural frequency and damping factor of the F-Ep composites increased with an increase in the fiber content. The F-Ep composite (45F-Ep) that exhibited better damping was selected for performing the drilling operation. Factors such as spindle speed (rpm), feed rate (mm/min) and drill point angle (degree) were chosen as input parameters and the tabulated set of experiments were in accordance with Taguchi’s design of experiment. The response measured was thrust force and the obtained values were found in the range of 19.66 to 50.75 N. The minimum value of thrust force was achieved when the F-Ep composite was drilled at high spindle speed (3000 rpm), with a feed rate of 75 mm/min using the drill point angle of 118°. ANOVA analysis showed that the developed regression model was significant and thrust force was mainly influenced by the spindle speed. Mathematical models were developed for drilling F-Ep composite using response surface methodology (RSM) and adaptive neuro fuzzy inference system (ANFIS) and compared for their efficacy.