DHDong Huang

Dong Huang

*This is an algorithmically generated author record based on publicly available information.

Dong Huang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Analysis of the Energy Loss Characteristics of a Francis Turbine Under Off-Design Conditions with Sand-Laden Flow Based on Entropy Generation Theory

    by Xudong Lu, Kang Xu, Zhongquan Wang, Yu Xiao, Yaogang Xu, Changjiu Huang, Jiayang Pang, Xiaobing Liu

    To investigate the impact of sand-laden flow on energy loss in Francis turbines, this study integrates entropy generation theory with numerical simulations conducted using ANSYS CFX. The mixture multiphase flow model and the SST k-ω turbulence model are employed to simulate the solid–liquid two-phase flow throughout the entire flow passage of the turbine at the Gengda Hydropower Station (Minjiang River Basin section, 103°17′ E and 31°06′ N). The energy loss characteristics under different off-design conditions are analyzed on the basis of the average sediment concentration during the flood season (2.9 kg/m3) and a median particle diameter of 0.058 mm. The results indicate that indirect entropy generation and wall entropy generation are the primary contributors to total energy loss, while direct entropy generation accounts for less than 1%. As the guide vane opening increases, the proportion of wall entropy generation initially rises and then decreases, while the total indirect entropy generation exhibits a non-monotonic trend dominated by the flow pattern in the draft tube. Entropy generation on the runner walls increases steadily with larger openings, whereas entropy generation on the draft tube walls first decreases and then increases. The variation in entropy generation on the guide vanes remains relatively small. These findings provide technical support for the optimal design and operation of turbines in sediment-rich rivers.


  • Open Access

    Wear Testing and Anti-Wear Performance Analysis of Surface Coating Materials for Stay Vanes of a Francis Turbine

    by Yangyang Hu, Lijie Zhang, Xiaobing Liu, Yongzhong Zeng, Jiayang Pang, Tianlin Li, Yuanjiang Ma, Zhongquan Wang, Longchao Gan, Dong Huang

    The wear of the flow passage components of the turbine due to sediment in sandy rivers is an inevitable challenge for hydroelectric units, often requiring frequent maintenance of hydraulic turbines. Consequently, the anti-wear protection technologies of hydraulic turbine components have garnered significant attention. In this study, three coating materials were analyzed for the stay vanes of the Francis turbine commonly used in hydropower stations. These materials, including JX ceramic metal wear-resistant material (JX33083), 3D printing additive manufacturing cermet material, and Foshilan polymer material, were tested for sediment wear, and their anti-wear performance was evaluated. The research results indicate that the anti-wear performance of the three coating materials is almost identical when the velocity on the surface of the stay vanes is below 7.5 m/s. Notably, 3D printing additive manufacturing cermet material demonstrates the best anti-wear performance when the velocity exceeds 7.5 m/s. The anti-wear effect of this coating material is 3.27 times more wear-resistant than Foshilan polymer material and 6.39 times more wear-resistant than JX ceramic metal wear-resistant material. Hence, these research findings provide a technical basis for the selection, operation, and maintenance of anti-wear coatings for the stay vanes of turbines in hydropower stations.


  • Open Access

    Design and Validation of a Testing Device for Sediment-Induced Erosion Based on Similarity Theory

    by Yuanjiang Ma, Xiaosong Pang, Zhongquan Wang, Dong Huang, Xiaobing Liu, Yongzhong Zeng, Bing Yao, Jiayang Pang, Yuanyuan Gang, Yangyang Hu, et al.

    Sediment-induced erosion is a primary cause of failure in the flow-passage components of Francis turbine units. This study adopted the Realizable k–ε turbulence model to numerically simulate the effects of sediment-induced erosion on the guide components of Francis turbines. Specifically, using flow similarity theory, a testing device suitable for studying the sediment-induced erosion behavior of turbine vanes was designed, and the similarity between the flow fields of actual vanes and testing device vanes was validated. The results revealed a high degree of consistency between the near-wall flow velocities and sediment volume fractions experienced by both vanes at 0.5 vane height. For instance, the midsection of the suction side of the stay and guide vanes exhibited relatively stable velocities of 12.5 m/s and 42 m/s, respectively. Further, sediment volume fractions at the leading edge of the stay and guide vanes reached 0.015, respectively, owing to the impact of sediment-laden flow. Overall, the proposed testing device design methodology can predict the operational lifespan of actual vanes and assess the wear resistance of various coating materials. These findings provide valuable scientific guidance for optimizing the design and operation of hydropower plants.


  • Open Access

    Numerical Simulation of Flow Fields and Sediment-Induced Wear in the Francis Turbine

    by Bing Xue, Yongbo Li, Youping Li, Zhengyang Tang, Bo Xu, Kang Xu, Ziyao Zhou, Zhishun Yu, Bing Yao, Jiayang Pang, et al.

    Based on the solid–liquid two-phase flow model and the Realizable k-ε Turbulence model, numerical simulations of the sediment–water flow in the flow components of the turbine were conducted. The distribution of sediment-induced wear within the turbine was obtained by analyzing the sediment volume fraction (SVF) and the erosion rate. The results revealed that sediment-induced wear on the stay and guide vanes was primarily distributed along the water inlet edge of the stay and guide vanes. For the runner blades, wear was predominantly localized along the water inlet edge and near the lower ring. The sediment-induced wear patterns on these flow components were found to be consistent with the sediment volume fractions (SVFs) on their surfaces.