Zhaoyang Wang
Research Subjects
Zhaoyang Wang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Bing Wu
School of Rail Transportation, Soochow University, Suzhou 215131, China
3 shared publications Shuai Wu
2 shared publicationsBing Wu
1 shared publicationCheng-Feng Du
1 shared publicationDingkang Li
1 shared publicationHong Yu
1 shared publication
Latest Publications
- 1 June 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (6)
Coupling effects of spin and temperature on transient wheel–rail adhesion under mixed lubrication
Wheel–rail adhesion is not a singular physical process but a dynamic response system arising from the complex interplay of spin, rolling–sliding motion, thermal effects, surface roughness, and environmental media. Understanding these interacting mechanisms is essential for train operational safety. This paper proposes a novel three-dimensional dynamic numerical model aimed at elucidating the adhesion mechanism under thermal mixed lubrication conditions, with a focus on the strong coupling among fluid, thermal, and roughness effects. The model consists of three key modules: a vehicle-track coupled dynamics model (VTDM) considering water lubrication, a kinematic model of the wheel–rail contact interface, and a dynamic wheel–rail adhesion model. Time-varying rolling contact parameters are obtained using the VTDM and fed into the kinematic model to determine the velocity field within the contact patch, followed by the solution of the dynamic adhesion model under thermal mixed lubrication conditions. Simulation results reveal that the lateral velocity component induced by spin and lateral creepage generates an asymmetric temperature distribution within the fluid-filled contact patch, with heat concentrated in the lateral direction, leading to localized attenuation of the fluid film. This effect is particularly pronounced at the trailing edge of the contact patch, where concentrated thermal stress renders it a primary location for fatigue crack initiation. The proposed three-dimensional model integrates fluid medium characteristics, spin motion, thermal effects, and surface roughness into a unified framework, providing a more comprehensive and mechanism-driven analytical tool for predicting wheel–rail adhesion behavior under complex operating conditions.
- 1 June 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (6)
Coupling effects of spin and temperature on transient wheel–rail adhesion under mixed lubrication
Wheel–rail adhesion is not a singular physical process but a dynamic response system arising from the complex interplay of spin, rolling–sliding motion, thermal effects, surface roughness, and environmental media. Understanding these interacting mechanisms is essential for train operational safety. This paper proposes a novel three-dimensional dynamic numerical model aimed at elucidating the adhesion mechanism under thermal mixed lubrication conditions, with a focus on the strong coupling among fluid, thermal, and roughness effects. The model consists of three key modules: a vehicle-track coupled dynamics model (VTDM) considering water lubrication, a kinematic model of the wheel–rail contact interface, and a dynamic wheel–rail adhesion model. Time-varying rolling contact parameters are obtained using the VTDM and fed into the kinematic model to determine the velocity field within the contact patch, followed by the solution of the dynamic adhesion model under thermal mixed lubrication conditions. Simulation results reveal that the lateral velocity component induced by spin and lateral creepage generates an asymmetric temperature distribution within the fluid-filled contact patch, with heat concentrated in the lateral direction, leading to localized attenuation of the fluid film. This effect is particularly pronounced at the trailing edge of the contact patch, where concentrated thermal stress renders it a primary location for fatigue crack initiation. The proposed three-dimensional model integrates fluid medium characteristics, spin motion, thermal effects, and surface roughness into a unified framework, providing a more comprehensive and mechanism-driven analytical tool for predicting wheel–rail adhesion behavior under complex operating conditions.
- 20 June 2025
- Published by Elsevier in Tribology International
- Vol. 211
Effects of wheel tread hollow wear on wheel-rail adhesion under wet condition
- 20 June 2025
- Published by Elsevier in Tribology International
- Vol. 211
Effects of wheel tread hollow wear on wheel-rail adhesion under wet condition
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Dynamic wheel–rail adhesion characteristics on wet curved tracks considering surface roughness
Wheel–rail rolling contact is a complex tribological issue, especially the existence of a thin water film on the rail surface, which leads to low adhesion problems for the traction and braking performance of the railway trains. The objective of this paper is to propose a non-Hertzian dynamic wheel–rail adhesion model for trains passing through wet curved tracks considering wheel–rail surface roughness. A vehicle-track coupling dynamics model was first developed to output the wheel–rail dynamic contact parameters under wet conditions. These parameters were subsequently utilized as dynamic inputs for the present wheel–rail adhesion model to simulate dynamic curve passing. The present numerical model includes the normal contact model and tangential model. For the normal contact issue, an elastohydrodynamic lubrication model was used to accurately determine the normal contact stress within the contact patch along the contact traces. Based on the normal contact characteristics, the advanced extended creep force model was used to compute the tangential stress. Finally, the dynamic wheel–rail adhesion coefficient can be obtained. This model considers the effects of time variation and changes in contact geometry, resulting in sudden increases or decreases in the adhesion coefficient at certain locations. At a speed of 400 km/h, a higher spin creepage occurs, leading to an increased displacement of the third-body layer and causing the maximum tangential stress to shift from one side of the contact patch to the other. Under the combined influence of the creepages, the maximum tangential stress occurs at the trailing edge of the contact patch.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Dynamic wheel–rail adhesion characteristics on wet curved tracks considering surface roughness
Wheel–rail rolling contact is a complex tribological issue, especially the existence of a thin water film on the rail surface, which leads to low adhesion problems for the traction and braking performance of the railway trains. The objective of this paper is to propose a non-Hertzian dynamic wheel–rail adhesion model for trains passing through wet curved tracks considering wheel–rail surface roughness. A vehicle-track coupling dynamics model was first developed to output the wheel–rail dynamic contact parameters under wet conditions. These parameters were subsequently utilized as dynamic inputs for the present wheel–rail adhesion model to simulate dynamic curve passing. The present numerical model includes the normal contact model and tangential model. For the normal contact issue, an elastohydrodynamic lubrication model was used to accurately determine the normal contact stress within the contact patch along the contact traces. Based on the normal contact characteristics, the advanced extended creep force model was used to compute the tangential stress. Finally, the dynamic wheel–rail adhesion coefficient can be obtained. This model considers the effects of time variation and changes in contact geometry, resulting in sudden increases or decreases in the adhesion coefficient at certain locations. At a speed of 400 km/h, a higher spin creepage occurs, leading to an increased displacement of the third-body layer and causing the maximum tangential stress to shift from one side of the contact patch to the other. Under the combined influence of the creepages, the maximum tangential stress occurs at the trailing edge of the contact patch.
- 27 October 2024
- Published by Wiley in Lubrication Science
- Vol. 37 (1) , 105-116
A Simplified Non‐Hertzian Wheel‐Rail Adhesion Model Under Interfacial Contaminations Considering Surface Roughness
The accuracy and efficiency of the wheel‐rail adhesion model are important to the wheel‐rail rolling contact issues. The purpose of this study is to develop a simplified non‐Hertzian wheel‐rail adhesion model under interfacial contaminations to predict the wheel‐rail adhesion coefficient. Firstly, a non‐Hertzian full elasto‐hydrodynamic lubrication (EHL) model was developed and applied to determine the wheel‐rail contact pressure and film thickness under interfacial contaminations. Then, the empirical formula of central film thickness available to non‐Hertzian wheel‐rail normal contact relating to train speeds, axle loads and material parameters were proposed based on a large number of non‐Hertzian full EHL simulation for smooth surface under interfacial contaminations using linear regression. The empirical non‐Hertzian central film thickness formula and minimum film thickness formula for wheel‐rail contact obtained in this paper show certain differences from the formulas based on Hertzian contact. Using the proposed non‐Hertzian central film thickness formula, a simplified non‐Hertzian wheel‐rail contact adhesion model was developed, and the adhesion coefficient was obtained at different speeds and compared with the field test data. The numerical results showed good agreement with field test data.
- 27 October 2024
- Published by Wiley in Lubrication Science
- Vol. 37 (1) , 105-116
A Simplified Non‐Hertzian Wheel‐Rail Adhesion Model Under Interfacial Contaminations Considering Surface Roughness
The accuracy and efficiency of the wheel‐rail adhesion model are important to the wheel‐rail rolling contact issues. The purpose of this study is to develop a simplified non‐Hertzian wheel‐rail adhesion model under interfacial contaminations to predict the wheel‐rail adhesion coefficient. Firstly, a non‐Hertzian full elasto‐hydrodynamic lubrication (EHL) model was developed and applied to determine the wheel‐rail contact pressure and film thickness under interfacial contaminations. Then, the empirical formula of central film thickness available to non‐Hertzian wheel‐rail normal contact relating to train speeds, axle loads and material parameters were proposed based on a large number of non‐Hertzian full EHL simulation for smooth surface under interfacial contaminations using linear regression. The empirical non‐Hertzian central film thickness formula and minimum film thickness formula for wheel‐rail contact obtained in this paper show certain differences from the formulas based on Hertzian contact. Using the proposed non‐Hertzian central film thickness formula, a simplified non‐Hertzian wheel‐rail contact adhesion model was developed, and the adhesion coefficient was obtained at different speeds and compared with the field test data. The numerical results showed good agreement with field test data.