Wenguang Liao
Research Subjects
Research Interests
Wenguang Liao has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Xun Liu
Ohio State Univ, Dept Mat Sci & Engn, Columbus, OH 43210 USA
3 shared publications - Andrew Chihpin Chuang
X-Ray Science Division, Argonne National Laboratory, Lemont, USA
1 shared publication John Procario
1 shared publicationMichael J. Mills
1 shared publication- Milan Heczko
Institute of Physics of Materials, Czech Academy of Sciences, Brno, Czech Republic
1 shared publication - Tao Sun
Department of Materials Science and Engineering, University of Virginia, Charlottesville, USA
1 shared publication
Latest Publications
- Open Access
- 23 October 2026
- Published by Elsevier in SSRN Electronic Journal
Ultrasonic effects in wire arc additive manufacturing of dissimilar aluminum alloys
Wire arc additive manufacturing (WAAM) enables the fabrication of large-scale metallic functionally graded materials (FGMs), but achieving well-controlled gradients remains challenging because melt-pool dynamics and cyclic thermal history continuously reshape the deposit beyond the imposed feedstock sequence. This study examines how ultrasonic assistance (UA) modifies the coupled mass transport, microstructural evolution, and thermomechanical response in WAAM of alternating TiB₂-reinforced AA7075-NT and AA5183 deposition. Based on high-energy synchrotron diffraction analysis of the UA and no-UA build, both the orthogonal-sector α-Al {111} lattice-spacing and full-ring azimuthal harmonic decomposition showed that UA reduced residual stress. The mean orthogonal spacing difference decreased from 37.1 ± 1.5 × 10⁻⁴ Å without UA to 27.9 ± 3.2 × 10⁻⁴ Å with UA. Layer-resolved residual stress further suggested a stronger reduction in the upper build, consistent with a growing contribution from UA thermal homogenization as heat accumulated. Enhanced TiB₂ transfer and dispersion, Al₆(Mn, Fe) formation in a UA-treated AA7075-NT layer, and altered local η-phase selection indicated that UA enhanced cross-layer mass transport of particles and alloying elements. In this studied WAAM material combinations, UA led to grain coarsening rather than the commonly reported refinement. This is attributed to acoustic-streaming-induced reductions in constitutional undercooling, which limit activation of the already abundant TiB₂ heterogeneous nucleation sites. Despite coarsening, UA increased hardness across most evaluated layers and reduced the pore area fraction from 1.65 ± 0.15% to 0.79 ± 0.12%.
- 23 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessUltrasonic effects in wire arc additive manufacturing of dissimilar aluminum alloys
Wire arc additive manufacturing (WAAM) enables the fabrication of large-scale metallic functionally graded materials (FGMs), but achieving well-controlled gradients remains challenging because melt-pool dynamics and cyclic thermal history continuously reshape the deposit beyond the imposed feedstock sequence. This study examines how ultrasonic assistance (UA) modifies the coupled mass transport, microstructural evolution, and thermomechanical response in WAAM of alternating TiB₂-reinforced AA7075-NT and AA5183 deposition. Based on high-energy synchrotron diffraction analysis of the UA and no-UA build, both the orthogonal-sector α-Al {111} lattice-spacing and full-ring azimuthal harmonic decomposition showed that UA reduced residual stress. The mean orthogonal spacing difference decreased from 37.1 ± 1.5 × 10⁻⁴ Å without UA to 27.9 ± 3.2 × 10⁻⁴ Å with UA. Layer-resolved residual stress further suggested a stronger reduction in the upper build, consistent with a growing contribution from UA thermal homogenization as heat accumulated. Enhanced TiB₂ transfer and dispersion, Al₆(Mn, Fe) formation in a UA-treated AA7075-NT layer, and altered local η-phase selection indicated that UA enhanced cross-layer mass transport of particles and alloying elements. In this studied WAAM material combinations, UA led to grain coarsening rather than the commonly reported refinement. This is attributed to acoustic-streaming-induced reductions in constitutional undercooling, which limit activation of the already abundant TiB₂ heterogeneous nucleation sites. Despite coarsening, UA increased hardness across most evaluated layers and reduced the pore area fraction from 1.65 ± 0.15% to 0.79 ± 0.12%.
- 14 September 2025
- Published by Elsevier in Materialia
- Vol. 44
Investigations on the effect of Nb on acicular ferrite dominant weld metal microstructure and toughness
- 14 September 2025
- Published by Elsevier in Materialia
- Vol. 44
Investigations on the effect of Nb on acicular ferrite dominant weld metal microstructure and toughness
- 15 October 2024
- Published by Elsevier in Materialia
- Vol. 38
Underlying mechanisms for the effect of Nb micro-alloying on the elemental distribution and precipitation behavior in the X70 weld metal
- 15 October 2024
- Published by Elsevier in Materialia
- Vol. 38
Underlying mechanisms for the effect of Nb micro-alloying on the elemental distribution and precipitation behavior in the X70 weld metal