Ajay Ravi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ajay Ravi has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Yuqi Li
Stanford University
4 shared publications Angela Cai
Department of Materials Science and Engineering, Stanford University, Stanford, USA
3 shared publications- Xueli Zheng
Department of Materials Science and Engineering, Stanford University, Stanford, USA
3 shared publications - Yi Cui
Stanford University
3 shared publications Zaichun Liu
Department of Materials Science and Engineering, Stanford University, Stanford, USA
3 shared publicationsChenwei Liu
Department of Materials Science and Engineering, Stanford University, Stanford, USA
2 shared publications
Latest Publications
- 12 August 2026
- Published by Springer Nature in Nature Chemical Engineering
- Vol. 3 (8) , 460-469
Upcycling nanoscale fragments in industrial waste liquids for aqueous battery electrolytes
- 12 August 2026
- Published by Springer Nature in Nature Chemical Engineering
- Vol. 3 (8) , 460-469
Upcycling nanoscale fragments in industrial waste liquids for aqueous battery electrolytes
- Open Access
- 26 May 2026
- Published by National Academy of Sciences in Proceedings of the National Academy of Sciences
- Vol. 123 (22)
Atomic layer-deposited nucleation layers to control zinc morphology and suppress hydrogen evolution
Aqueous zinc (Zn) batteries are among the most promising candidates for safe, low-cost, and sustainable grid-scale energy storage. However, their practical application is significantly constrained by inhomogeneous Zn electrodeposition and the competitive hydrogen evolution reaction (HER). Here, we introduce an electrodeposition architecture to mitigate these challenges. Using atomic layer deposition, we coat the copper current collector with ZnO and Al 2 O 3 nanofilms—positioned below the plated Zn. Our strategy marks a significant departure from previous works in which thin films are situated above Zn foil to function as artificial solid electrolyte interphases. Notably, we achieve substantial performance improvements with our 2-nm-thick ZnO coatings, including long cycle life (>1,400 cycles) and high Coulombic efficiencies (>99.8%). Our mechanistic investigation suggests that these improvements arise from HER suppression and controlled Zn morphology. This work offers an interface engineering approach to fundamentally understand Zn nucleation and growth processes. We anticipate that our electrodeposition architecture could be applied to enhance the cyclability of other aqueous battery systems.
- 26 May 2026
- Published by National Academy of Sciences in Proceedings of the National Academy of Sciences
- Vol. 123 (22)
Open AccessAtomic layer-deposited nucleation layers to control zinc morphology and suppress hydrogen evolution
Aqueous zinc (Zn) batteries are among the most promising candidates for safe, low-cost, and sustainable grid-scale energy storage. However, their practical application is significantly constrained by inhomogeneous Zn electrodeposition and the competitive hydrogen evolution reaction (HER). Here, we introduce an electrodeposition architecture to mitigate these challenges. Using atomic layer deposition, we coat the copper current collector with ZnO and Al 2 O 3 nanofilms—positioned below the plated Zn. Our strategy marks a significant departure from previous works in which thin films are situated above Zn foil to function as artificial solid electrolyte interphases. Notably, we achieve substantial performance improvements with our 2-nm-thick ZnO coatings, including long cycle life (>1,400 cycles) and high Coulombic efficiencies (>99.8%). Our mechanistic investigation suggests that these improvements arise from HER suppression and controlled Zn morphology. This work offers an interface engineering approach to fundamentally understand Zn nucleation and growth processes. We anticipate that our electrodeposition architecture could be applied to enhance the cyclability of other aqueous battery systems.
- 27 January 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (5) , 5048-5056
NiSO 4 -Driven In Situ Alloy Formation To Unlock Highly Reversible Iron Electrochemistry in Aqueous Batteries
- 27 January 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (5) , 5048-5056
NiSO 4 -Driven In Situ Alloy Formation To Unlock Highly Reversible Iron Electrochemistry in Aqueous Batteries
- 27 June 2025
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 25 (27) , 10834-10839
Revealing and Quantifying Carbon Corrosion in Aqueous Manganese-Based Batteries
The MnO2/Mn2+ cathode chemistry represents a promising avenue for high-energy-density and low-cost aqueous batteries. However, its practical application for grid-scale storage is limited by insufficient cycling stability. Extensive reports have highlighted the poor reversibility of MnO2 deposition and stripping. Here, we reveal an overlooked source of capacity loss under typical operating conditions: corrosion of the carbon current collector. Using gas chromatography, we show that carbon corrosion can account for up to ∼25% of initial capacity losses and can cause thickness losses approaching 200 nm in the first cycle. Corrosion-induced thickness losses are largest under acidic and near-neutral conditions. Corroborating our corrosion measurements, X-ray photoelectron spectroscopy and scanning electron microscopy results indicate the formation of surface oxygen species and carbon fiber degradation after cycling. Our work provides a quantitative understanding of carbon corrosion in aqueous batteries that can inform strategies for extending their cycle life.
- 27 June 2025
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 25 (27) , 10834-10839
Revealing and Quantifying Carbon Corrosion in Aqueous Manganese-Based Batteries
The MnO2/Mn2+ cathode chemistry represents a promising avenue for high-energy-density and low-cost aqueous batteries. However, its practical application for grid-scale storage is limited by insufficient cycling stability. Extensive reports have highlighted the poor reversibility of MnO2 deposition and stripping. Here, we reveal an overlooked source of capacity loss under typical operating conditions: corrosion of the carbon current collector. Using gas chromatography, we show that carbon corrosion can account for up to ∼25% of initial capacity losses and can cause thickness losses approaching 200 nm in the first cycle. Corrosion-induced thickness losses are largest under acidic and near-neutral conditions. Corroborating our corrosion measurements, X-ray photoelectron spectroscopy and scanning electron microscopy results indicate the formation of surface oxygen species and carbon fiber degradation after cycling. Our work provides a quantitative understanding of carbon corrosion in aqueous batteries that can inform strategies for extending their cycle life.
- 8 November 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (6)
Comparison of Al- and Hf-based hybrid photoresists grown by molecular layer deposition for extreme ultraviolet lithography
The continued downscaling of electronic device dimensions requires the development of high-performance resist materials for advanced lithographic patterning. In this study, we examine Al-based hybrid “alucone” thin films grown by molecular layer deposition (MLD) for application to extreme ultraviolet (EUV) lithography and compare their resist properties with those of previously studied Hf-based MLD hybrid “hafnicone.” Both alucone films presented here—standard alucone and oxygen-rich alucone—are deposited using the precursors trimethylaluminum and ethylene glycol. Using electron-beam lithography as a proxy for EUV, we demonstrate that alucone behaves as a negative-tone resist capable of resolving line widths down to ∼20 nm. It is found that the sensitivity of oxygen-rich alucone is 4800 μC/cm2 using 0.125M HCl as the developer, whereas standard alucone is somewhat less sensitive. The resolution of alucone is higher than that of hafnicone, although the sensitivity is poorer. By performing x-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy, we investigate the degradation mechanism of standard alucone and compare this mechanism to that of hafnicone. We rationalize the observed differences in resist behavior between hafnicone and alucone by considering the oxophilicity of the metal atom in the respective thin films. This study provides a deeper understanding of the relationship between MLD film chemistry and irradiation responsiveness, which can help advance the optimization of resist materials for microelectronics fabrication.
- 8 November 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (6)
Comparison of Al- and Hf-based hybrid photoresists grown by molecular layer deposition for extreme ultraviolet lithography
The continued downscaling of electronic device dimensions requires the development of high-performance resist materials for advanced lithographic patterning. In this study, we examine Al-based hybrid “alucone” thin films grown by molecular layer deposition (MLD) for application to extreme ultraviolet (EUV) lithography and compare their resist properties with those of previously studied Hf-based MLD hybrid “hafnicone.” Both alucone films presented here—standard alucone and oxygen-rich alucone—are deposited using the precursors trimethylaluminum and ethylene glycol. Using electron-beam lithography as a proxy for EUV, we demonstrate that alucone behaves as a negative-tone resist capable of resolving line widths down to ∼20 nm. It is found that the sensitivity of oxygen-rich alucone is 4800 μC/cm2 using 0.125M HCl as the developer, whereas standard alucone is somewhat less sensitive. The resolution of alucone is higher than that of hafnicone, although the sensitivity is poorer. By performing x-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy, we investigate the degradation mechanism of standard alucone and compare this mechanism to that of hafnicone. We rationalize the observed differences in resist behavior between hafnicone and alucone by considering the oxophilicity of the metal atom in the respective thin films. This study provides a deeper understanding of the relationship between MLD film chemistry and irradiation responsiveness, which can help advance the optimization of resist materials for microelectronics fabrication.