Allam Musbah Al Allam
Research Subjects
Allam Musbah Al Allam has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed Suliman B. Ali
Universiti Teknologi MARA
4 shared publications - Shaban Ismael Albrka Ali
Department of Civil and Construction Engineering, College of Engineering, A’Sharqiyah University, Ibra 400, Oman
4 shared publications - Mohammad Al-Zu'BI
Department of Civil Engineering, Munib and Angela Masri Faculty of Engineering, Aqaba University of Technology, Aqaba 11947, Jordan
2 shared publications - Ahmed Eltwati
Department of civil Engineering, University of Benghazi, Benghazi 12345, Libya
1 shared publication Amhmmed Anbeeh Albaqoul
Engineering and Information Technology, Research Center, Bani Walid, Libya
1 shared publicationAshraf Abdalla M. Radwan
School of Civil Engineering, Faculty of Engineering, Universiti Teknologi Malaysia, Skudai 81310, Johor, Malaysia
1 shared publication
Latest Publications
- Open Access
- 24 August 2026
- Published by Digitodontics International Academy in University of Zawia Journal of Engineering Sciences and Technology
- Vol. 4 (2) , 113-120
Evaluation of the Causes and Consequences of Road Traffic Accidents on the Bani Walid–Tripoli Road, Libya
Road accidents worldwide are increasing, and the same problems are happening in Libya. Over the years, along the Bani Walid–Tripoli highway, the number of fatal crashes and related deaths has gradually increased. This research aims to evaluate infrastructural, behavioural, and socio-demographic factors associated with road accidents on this important route. Quantitative data were also analysed using SPSS Version 29. This work explores that 91% of respondents supported unsafe driving practices, while only 9% rejected them. In conclusion, this study contributes to improving road traffic accidents on the Bani Walid–Tripoli highway are mainly linked to reckless driving and poor road conditions. It is recommended that stronger radar-based speed enforcement, urgent road maintenance, and structured road-safety education programmes are needed to decrease accidents and protect road users.
- 24 August 2026
- Published by Digitodontics International Academy in University of Zawia Journal of Engineering Sciences and Technology
- Vol. 4 (2) , 113-120
Open AccessEvaluation of the Causes and Consequences of Road Traffic Accidents on the Bani Walid–Tripoli Road, Libya
Road accidents worldwide are increasing, and the same problems are happening in Libya. Over the years, along the Bani Walid–Tripoli highway, the number of fatal crashes and related deaths has gradually increased. This research aims to evaluate infrastructural, behavioural, and socio-demographic factors associated with road accidents on this important route. Quantitative data were also analysed using SPSS Version 29. This work explores that 91% of respondents supported unsafe driving practices, while only 9% rejected them. In conclusion, this study contributes to improving road traffic accidents on the Bani Walid–Tripoli highway are mainly linked to reckless driving and poor road conditions. It is recommended that stronger radar-based speed enforcement, urgent road maintenance, and structured road-safety education programmes are needed to decrease accidents and protect road users.
- Open Access
- 1 August 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (8) , 3368-3390
Coal Fly Ash Based Prime Coats for Enhanced Interlayer Adhesion in Flexible Pavements
The establishment of strong interlayer bonding between the base course and asphalt surface is critical for the durability of flexible pavements. Inadequate adhesion at this junction commonly causes slippage, fissures, and early deterioration, consequently diminishing pavement longevity and escalating maintenance expenses. Conventional prime coats, such as cutback and emulsified asphalts, possess drawbacks, including ecological issues and variable efficacy in adverse site conditions. This study investigates the Prime Coal Fly Ash Coat (PCFAC), which is developed utilizing Coal Fly Ash (CFA), an abundant industrial by-product, as an eco-friendly substitute for prime coats. Experimental work involved preparing granular base layers in accordance with laboratory specifications, followed by the application of PCFAC mixtures at different CFA-to-water ratios and distribution rates. Specimens were cured under laboratory conditions for 24 hours following base preparation and an additional 24 hours subsequent to PCFAC application before testing. Findings indicated that higher CFA content enhanced mixture stability and adhesion, with PCFAC-2.5 demonstrating optimal performance. The optimum distribution rate of 1.75 kg/m² was determined by comparing penetration depth, pull-off strength, and direct shear strength, balancing sufficient infiltration with strong adhesion and effective workability. At this rate, the PCFAC attained a pull-off tensile strength of 322 kPa and a direct shear strength of 3.5 MPa, signifying the highest values among the investigated PCFAC formulations. The findings highlight PCFAC’s capability to enhance interlayer bonding while valorizing industrial waste, thereby contributing to sustainable pavement practices. The manuscript further examines the limitations of the study, such as the adaptation of current testing standards, and proposes recommendations for further research and field validation.
- 1 August 2026
- Published by Ital Publication in Civil Engineering Journal
- Vol. 12 (8) , 3368-3390
Open AccessCoal Fly Ash Based Prime Coats for Enhanced Interlayer Adhesion in Flexible Pavements
The establishment of strong interlayer bonding between the base course and asphalt surface is critical for the durability of flexible pavements. Inadequate adhesion at this junction commonly causes slippage, fissures, and early deterioration, consequently diminishing pavement longevity and escalating maintenance expenses. Conventional prime coats, such as cutback and emulsified asphalts, possess drawbacks, including ecological issues and variable efficacy in adverse site conditions. This study investigates the Prime Coal Fly Ash Coat (PCFAC), which is developed utilizing Coal Fly Ash (CFA), an abundant industrial by-product, as an eco-friendly substitute for prime coats. Experimental work involved preparing granular base layers in accordance with laboratory specifications, followed by the application of PCFAC mixtures at different CFA-to-water ratios and distribution rates. Specimens were cured under laboratory conditions for 24 hours following base preparation and an additional 24 hours subsequent to PCFAC application before testing. Findings indicated that higher CFA content enhanced mixture stability and adhesion, with PCFAC-2.5 demonstrating optimal performance. The optimum distribution rate of 1.75 kg/m² was determined by comparing penetration depth, pull-off strength, and direct shear strength, balancing sufficient infiltration with strong adhesion and effective workability. At this rate, the PCFAC attained a pull-off tensile strength of 322 kPa and a direct shear strength of 3.5 MPa, signifying the highest values among the investigated PCFAC formulations. The findings highlight PCFAC’s capability to enhance interlayer bonding while valorizing industrial waste, thereby contributing to sustainable pavement practices. The manuscript further examines the limitations of the study, such as the adaptation of current testing standards, and proposes recommendations for further research and field validation.
- 11 June 2026
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 11 (7) , 369
Mechanical performance and durability of asphalt mixtures incorporating coal fly ash filler for sustainable pavement applications
- 11 June 2026
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 11 (7) , 369
Mechanical performance and durability of asphalt mixtures incorporating coal fly ash filler for sustainable pavement applications
- 8 August 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1155, 103-117
Assessing the Effect of Adding a Soft Clay Supplement on Hot Mix Asphalt Moisture Damage
Asphalt pavement performance is based on several parameters and properties of the materials’ element. surface free energy that the modifier and the asphalt binder both displays. The resistance of the modified asphalt binder to stresses and moisture damage is largely determined by the bond energies. Asphalt binder qualities may be altered by either technical or natural processes, which subsequently impact on the chemical and mechanical characteristics. In addition, a correlated investigation revealed that surface free energy values may be used to assess the compatibility of a binder in relation to moisture-induced damage. Data demonstrates that the incorporation of soft clay into the asphalt binder resulted in a favorable coating and bonding capacity, as compared to the control asphalt binder. moisture-induced damage in HMA is a combined effect of loss of cohesion of asphalt binder and loss of adhesion between asphalt binder and aggregate. It was indicated that the modified binders of BPSC ratios would delay and weaken the oxidation reaction asphalt binder which can enhance the aging process. Based on absorbance peaks of carbonyl and sulfoxide bonds, the addition of BPSC would delay the aging process of asphalt binder.
- 8 August 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1155, 103-117
Assessing the Effect of Adding a Soft Clay Supplement on Hot Mix Asphalt Moisture Damage
Asphalt pavement performance is based on several parameters and properties of the materials’ element. surface free energy that the modifier and the asphalt binder both displays. The resistance of the modified asphalt binder to stresses and moisture damage is largely determined by the bond energies. Asphalt binder qualities may be altered by either technical or natural processes, which subsequently impact on the chemical and mechanical characteristics. In addition, a correlated investigation revealed that surface free energy values may be used to assess the compatibility of a binder in relation to moisture-induced damage. Data demonstrates that the incorporation of soft clay into the asphalt binder resulted in a favorable coating and bonding capacity, as compared to the control asphalt binder. moisture-induced damage in HMA is a combined effect of loss of cohesion of asphalt binder and loss of adhesion between asphalt binder and aggregate. It was indicated that the modified binders of BPSC ratios would delay and weaken the oxidation reaction asphalt binder which can enhance the aging process. Based on absorbance peaks of carbonyl and sulfoxide bonds, the addition of BPSC would delay the aging process of asphalt binder.
- Open Access
Analysis of the Optimum Performance for Polymer and Polymer–Nanocomposite-modified Asphalt by Using Multicriteria Decision Analysis
The influence of Acrylate Styrene Acrylonitrile (ASA) and ASA/nanosilica (ASA/Si) additives was investigated by using a dynamic shear rheometer (DSR). Firstly, an ASA polymer was blended with the virgin asphalt binder at two different concentrations (3% ASA and 5% ASA). After observing that 5% ASA was the optimum concentration for modification, nanosilica particles were further incorporated into the 5% ASA-modified asphalt binder with two different percentages (5% ASA 3%Si; 5% ASA 5%Si). Frequency sweep tests were conducted across various frequencies at elevated temperatures. The experimental outcomes were analyzed using master curves, rutting, and fatigue resistance parameter plots. Additionally, to provide a more holistic analysis, two different multicriteria decision analysis (MCDA) techniques, namely the Preference Ranking Organization Method for Enrichment Evaluations (PROMETHEE) and the Technique for the Order of Preference by a Similarity to Ideal Solution (TOPSIS), were conducted to identify the best-performing asphalt binder by considering three different parameters: workability, performance under different conditions, and cost. The frequency sweep tests showed that the 5% ASA 5%Si asphalt worked best in terms of resistance to rutting. On the other hand, the virgin binder performed better than all modified binders when it failed to resist fatigue. On the other hand, the PROMETHEE analysis identified the 5% ASA-modified asphalt binder as the optimal choice, while the TOPSIS analysis determined that the 5% ASA 3%Si-modified binder provided the best performance. The differences between the experimental results and the MCDA were due to using more than one evaluation parameter and looking at how well the asphalt binder worked at different temperature ranges at the same time.
Open AccessAnalysis of the Optimum Performance for Polymer and Polymer–Nanocomposite-modified Asphalt by Using Multicriteria Decision Analysis
The influence of Acrylate Styrene Acrylonitrile (ASA) and ASA/nanosilica (ASA/Si) additives was investigated by using a dynamic shear rheometer (DSR). Firstly, an ASA polymer was blended with the virgin asphalt binder at two different concentrations (3% ASA and 5% ASA). After observing that 5% ASA was the optimum concentration for modification, nanosilica particles were further incorporated into the 5% ASA-modified asphalt binder with two different percentages (5% ASA 3%Si; 5% ASA 5%Si). Frequency sweep tests were conducted across various frequencies at elevated temperatures. The experimental outcomes were analyzed using master curves, rutting, and fatigue resistance parameter plots. Additionally, to provide a more holistic analysis, two different multicriteria decision analysis (MCDA) techniques, namely the Preference Ranking Organization Method for Enrichment Evaluations (PROMETHEE) and the Technique for the Order of Preference by a Similarity to Ideal Solution (TOPSIS), were conducted to identify the best-performing asphalt binder by considering three different parameters: workability, performance under different conditions, and cost. The frequency sweep tests showed that the 5% ASA 5%Si asphalt worked best in terms of resistance to rutting. On the other hand, the virgin binder performed better than all modified binders when it failed to resist fatigue. On the other hand, the PROMETHEE analysis identified the 5% ASA-modified asphalt binder as the optimal choice, while the TOPSIS analysis determined that the 5% ASA 3%Si-modified binder provided the best performance. The differences between the experimental results and the MCDA were due to using more than one evaluation parameter and looking at how well the asphalt binder worked at different temperature ranges at the same time.
- Open Access
- 31 December 2023
- Published by Tobruk University in Tobruk University Journal of Engineering Sciences
- Vol. 4 (2) , 1-11
Effect of Utilization RPET on the Physical Properties of Asphalt Binder
Through the utilization of waste materials in asphalt pavement, such as plastic water bottles made of Polyethylene Terephthalate (RPET), it is possible to explore alternative solutions that can enhance the service life of asphalt pavement while simultaneously reducing environmental pollution. This research specifically investigates the viability of incorporating waste plastic bottles, made of RPET, as polymer additives in asphalt binder to address common pavement issues. three different proportions of RPET (3%, 5%, and 7%) were added by weight of optimum binder to prepare the specimens. Various tests were conducted, including the physical properties and viscosity. The findings revealed that the optimal modifier content was 5% for the RPET-modified asphalt binder. This composition demonstrated maximum stability. It is observed that the addition of RPET to the asphalt binder resulted in a reduction in penetration values and an increase in softening points. Furthermore, it exhibited improved resistance against permanent deformations and superior engineering properties. This research contributes to the field of modified binder, and waste plastic, specifically Polyethylene Terephthalate (RPET), by providing valuable insights and highlighting the potential benefits of utilizing such materials in pavement construction.
- 31 December 2023
- Published by Tobruk University in Tobruk University Journal of Engineering Sciences
- Vol. 4 (2) , 1-11
Open AccessEffect of Utilization RPET on the Physical Properties of Asphalt Binder
Through the utilization of waste materials in asphalt pavement, such as plastic water bottles made of Polyethylene Terephthalate (RPET), it is possible to explore alternative solutions that can enhance the service life of asphalt pavement while simultaneously reducing environmental pollution. This research specifically investigates the viability of incorporating waste plastic bottles, made of RPET, as polymer additives in asphalt binder to address common pavement issues. three different proportions of RPET (3%, 5%, and 7%) were added by weight of optimum binder to prepare the specimens. Various tests were conducted, including the physical properties and viscosity. The findings revealed that the optimal modifier content was 5% for the RPET-modified asphalt binder. This composition demonstrated maximum stability. It is observed that the addition of RPET to the asphalt binder resulted in a reduction in penetration values and an increase in softening points. Furthermore, it exhibited improved resistance against permanent deformations and superior engineering properties. This research contributes to the field of modified binder, and waste plastic, specifically Polyethylene Terephthalate (RPET), by providing valuable insights and highlighting the potential benefits of utilizing such materials in pavement construction.