Liu Chang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Liu Chang has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Liyi Li
School of Integrated Circuits, Southeast University, Wuxi 214000, China
4 shared publications - Cong Mei
School of Integrated Circuits, Southeast University, Wuxi 214000, China
3 shared publications - Qiuhan Hu
School of Advanced Technology, Xi’an Jiaotong-Liverpool University, Suzhou 215123, China
3 shared publications - Tianze Zheng
School of Integrated Circuits, Southeast University, Wuxi 214000, China
3 shared publications - Gangli Yang
School of Integrated Circuits, Southeast University, Wuxi 214000, China
2 shared publications - Tailong Shi
School of Integrated Circuits, Southeast University, Wuxi 214000, China
2 shared publications
Latest Publications
- Open Access
- 19 May 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (5) , 625
A Comprehensive Experimental and Finite Element Analysis Study on the Bonding Strength Evaluation of Wafer-to-Wafer Hybrid Bonding with Polyimide Film Dielectrics
Polymer insulation layers such as polyimide (PI) have gradually replaced inorganic dielectric layers (SiO2, SiCN) in the integrated packaging process of hybrid bonding (HB). PI can fill the gaps in the thermal compression bonding process and help to obtain a good Cu/Polymer bonding interface. At present, the existing post-crack double cantilever beam tensile test (PBC-DCB) has been successfully applied to the quantitative measurement of bonding strength of hybrid bonding with inorganic materials, but this method only considers elastic behavior. Since PI exhibits viscidity, elasticity and plasticity, knowing how to correlate these properties to the bonding process is challenging. Whether PBC-DCB is suitable for the characterization of PI bonding is unclear. This paper presents a comprehensive experimental and finite element analysis (FEA) study on the PI–PI bonding interface. Firstly, nanoindentation experiments and simulations are performed on the prepared PI interface to obtain key elasticity and plasticity parameters. Then, the bonding strength is characterized by the PBC-DCB test. Theoretical and experimental results show that the plasticity of PI causes energy dissipation during stretching, resulting in a deviation of approximately 2.51% compared with pure elasticity. Based on experimental data, the Cohesive Zone Model (CZM) FEA method is used to simulate the crack propagation. The results indicate that the Embedded Process Zone (EPZ) model can accurately describe crack initiation and delamination behavior, with a margin of error of about 3.61%. Finally, based on the EPZ CZM, defects such as bonding void and wafer warpage are further discussed in relation to bonding strength measurement.
- 19 May 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (5) , 625
Open AccessA Comprehensive Experimental and Finite Element Analysis Study on the Bonding Strength Evaluation of Wafer-to-Wafer Hybrid Bonding with Polyimide Film Dielectrics
Polymer insulation layers such as polyimide (PI) have gradually replaced inorganic dielectric layers (SiO2, SiCN) in the integrated packaging process of hybrid bonding (HB). PI can fill the gaps in the thermal compression bonding process and help to obtain a good Cu/Polymer bonding interface. At present, the existing post-crack double cantilever beam tensile test (PBC-DCB) has been successfully applied to the quantitative measurement of bonding strength of hybrid bonding with inorganic materials, but this method only considers elastic behavior. Since PI exhibits viscidity, elasticity and plasticity, knowing how to correlate these properties to the bonding process is challenging. Whether PBC-DCB is suitable for the characterization of PI bonding is unclear. This paper presents a comprehensive experimental and finite element analysis (FEA) study on the PI–PI bonding interface. Firstly, nanoindentation experiments and simulations are performed on the prepared PI interface to obtain key elasticity and plasticity parameters. Then, the bonding strength is characterized by the PBC-DCB test. Theoretical and experimental results show that the plasticity of PI causes energy dissipation during stretching, resulting in a deviation of approximately 2.51% compared with pure elasticity. Based on experimental data, the Cohesive Zone Model (CZM) FEA method is used to simulate the crack propagation. The results indicate that the Embedded Process Zone (EPZ) model can accurately describe crack initiation and delamination behavior, with a margin of error of about 3.61%. Finally, based on the EPZ CZM, defects such as bonding void and wafer warpage are further discussed in relation to bonding strength measurement.
- Open Access
Analysis of Post-Bonding Crack-Induced Double Cantilever Bending (PDC-DCB) Method for Hybrid Bonding Strength Measurement
The quantitative measurement of bonding strength in hybrid bonding (HB) is an indispensable metrology for process and reliability evaluation. Methods currently used such as blade insertion (BI) and double cantilever bending (DCB) have suffered from a wafer edge-only capability and limited repeatability due to a lack of precise interface crack initiation. This study reports an improved DCB method by introducing a post-bonding crack (PBC) to avoid undesired cracking in a wafer substrate during DCB propagation. This method is firstly applied to measure the bonding strength of SiCN-SiCN under O2 and N2 activation. The test data shows that the bonding strengths are 3.53 J/m2 and 2.93 J/m2 with the deviations less than 3.84% and 1.84%. Based on the experimental data, finite element analysis (FEA) methods are used to simulate the crack propagation process of the PBC-DCB method. The results show that the bonding interface crack propagation can be accurately described by an optimized viscoelastic exponential model. The accuracy of simulation increased from 16.06% to 1.77%. Finally, it was found that the PBC-DCB method can solve the issue in conventional DCB where the crack may be initiated away from the target interface, therefore measuring the wrong interface. This advantage is further validated by simulations considering the offset of the PBC away from the bonding interface.
Open AccessAnalysis of Post-Bonding Crack-Induced Double Cantilever Bending (PDC-DCB) Method for Hybrid Bonding Strength Measurement
The quantitative measurement of bonding strength in hybrid bonding (HB) is an indispensable metrology for process and reliability evaluation. Methods currently used such as blade insertion (BI) and double cantilever bending (DCB) have suffered from a wafer edge-only capability and limited repeatability due to a lack of precise interface crack initiation. This study reports an improved DCB method by introducing a post-bonding crack (PBC) to avoid undesired cracking in a wafer substrate during DCB propagation. This method is firstly applied to measure the bonding strength of SiCN-SiCN under O2 and N2 activation. The test data shows that the bonding strengths are 3.53 J/m2 and 2.93 J/m2 with the deviations less than 3.84% and 1.84%. Based on the experimental data, finite element analysis (FEA) methods are used to simulate the crack propagation process of the PBC-DCB method. The results show that the bonding interface crack propagation can be accurately described by an optimized viscoelastic exponential model. The accuracy of simulation increased from 16.06% to 1.77%. Finally, it was found that the PBC-DCB method can solve the issue in conventional DCB where the crack may be initiated away from the target interface, therefore measuring the wrong interface. This advantage is further validated by simulations considering the offset of the PBC away from the bonding interface.
- Open Access
- 21 November 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (12) , 1304
Post-Bonding Crack-Induced Di-Cantilever Bending (PBC-DCB): A Novel Method for Quantitative Evaluation of Bonding Strength for Wafer-to-Wafer and Die-to-Wafer Hybrid Bonding
To address the challenge of characterizing bonding strength in hybrid bonding, this paper proposes a method based on post-bonding crack-induced di-cantilever bending (PBC-DCB). The commonly used industrial blade insertion (BI) method only measures the edge strength of wafer-to-wafer samples via bevel geometry, failing to characterize the wafer center or die-to-wafer samples (as they lack a bevel) and exhibiting limited accuracy due to irregular crack edges. This study develops a di-cantilever beam test initiated by a specially prepared post-bonding notch. By deriving the relationship between load–displacement and bonding strength based on fracture mechanics and optimizing sample preparation and testing parameters, quantitative measurement of interface fracture strength is achieved. Experimental results show the method has a deviation < 5% from BI with better repeatability, verifying its reliability. It successfully distinguishes bonding strength between wafer center and edge and reveals that SiCN dielectric layers have 17.34% higher strength and better uniformity than SiO2. This provides a reliable testing tool for hybrid bonding quality and process optimization, with broad prospects in industrial production and scientific research.
- 21 November 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (12) , 1304
Open AccessPost-Bonding Crack-Induced Di-Cantilever Bending (PBC-DCB): A Novel Method for Quantitative Evaluation of Bonding Strength for Wafer-to-Wafer and Die-to-Wafer Hybrid Bonding
To address the challenge of characterizing bonding strength in hybrid bonding, this paper proposes a method based on post-bonding crack-induced di-cantilever bending (PBC-DCB). The commonly used industrial blade insertion (BI) method only measures the edge strength of wafer-to-wafer samples via bevel geometry, failing to characterize the wafer center or die-to-wafer samples (as they lack a bevel) and exhibiting limited accuracy due to irregular crack edges. This study develops a di-cantilever beam test initiated by a specially prepared post-bonding notch. By deriving the relationship between load–displacement and bonding strength based on fracture mechanics and optimizing sample preparation and testing parameters, quantitative measurement of interface fracture strength is achieved. Experimental results show the method has a deviation < 5% from BI with better repeatability, verifying its reliability. It successfully distinguishes bonding strength between wafer center and edge and reveals that SiCN dielectric layers have 17.34% higher strength and better uniformity than SiO2. This provides a reliable testing tool for hybrid bonding quality and process optimization, with broad prospects in industrial production and scientific research.
- Open Access
- 14 November 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (11) , 1370
A Study on Regulating the Residual Stress of Electroplated Cu by Manipulating the Nanotwin Directions
Glass substrate, a new type of substrate with excellent mechanical and electrical properties of glass itself, has great potential to become an ideal platform for heterogeneous integration in chiplet systems for high-performance computing applications. The residual stress of the metal layer generated on the glass surface during the electroplating process is one of the major bottlenecks of glass packaging technologies, resulting in glass-metal layer delamination and glass breakage. This paper demonstrated for the first time a method to regulate the residual stress by manipulating the nanotwin directions of the electroplated Cu. The experimental results show that nanotwins with three different directions (non-directional, vertical, and horizontal) can be manipulated by controlling electroplating conditions (concentration of Cl− and gelatin, stirring speed). The orientations of non-directional, vertical, and horizontal nanotwinned Cu are non-oriented, 110 and 111, respectively. After electroplating, the 111-oriented nanotwinned Cu has the smallest residual stress (39.7 MPa). Annealing can significantly reduce the residual stress of nanotwinned Cu, which has been attributed to the decrease in the geometric necessity dislocation density. 110-oriented nanotwinned Cu had drastic recrystallization, while 111-oriented nanotwinned Cu and non-oriented nanotwinned Cu had only slight recrystallization. After annealing, the residual stress of 111-nt-Cu remains the lowest (29.1 MPa).
- 14 November 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (11) , 1370
Open AccessA Study on Regulating the Residual Stress of Electroplated Cu by Manipulating the Nanotwin Directions
Glass substrate, a new type of substrate with excellent mechanical and electrical properties of glass itself, has great potential to become an ideal platform for heterogeneous integration in chiplet systems for high-performance computing applications. The residual stress of the metal layer generated on the glass surface during the electroplating process is one of the major bottlenecks of glass packaging technologies, resulting in glass-metal layer delamination and glass breakage. This paper demonstrated for the first time a method to regulate the residual stress by manipulating the nanotwin directions of the electroplated Cu. The experimental results show that nanotwins with three different directions (non-directional, vertical, and horizontal) can be manipulated by controlling electroplating conditions (concentration of Cl− and gelatin, stirring speed). The orientations of non-directional, vertical, and horizontal nanotwinned Cu are non-oriented, 110 and 111, respectively. After electroplating, the 111-oriented nanotwinned Cu has the smallest residual stress (39.7 MPa). Annealing can significantly reduce the residual stress of nanotwinned Cu, which has been attributed to the decrease in the geometric necessity dislocation density. 110-oriented nanotwinned Cu had drastic recrystallization, while 111-oriented nanotwinned Cu and non-oriented nanotwinned Cu had only slight recrystallization. After annealing, the residual stress of 111-nt-Cu remains the lowest (29.1 MPa).