Haiwei Li
Research Subjects
Haiwei Li has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Bo Wang
Key Laboratory of Cluster Science, Ministry of Education, School of Interdisciplinary Science, School of Chemistry and Chemical Engineering, Advanced Technology Research Institute (Jinan) Beijing Institute of Technology Beijing China
2 shared publications Junwen Zhou
Beijing National Laboratory for Molecular Sciences (BNLMS)
2 shared publications- Bingyin Luo
Integrated Circuit R&D Center, ICBG China Resources Microelectronics Co., Ltd., Shanghai 200072, China
1 shared publication Daidai Chen
The Key Laboratory of Automotive Electronics Intelligentization of Zhejiang Province,Ningbo,Zhejiang,China
1 shared publication- Haifeng Dai
College of Automotive and Energy Engineering Tongji University Shanghai China
1 shared publication - Jiangwei Wang
School of Automotive Studies, Tongji University, Shanghai 201804, China
1 shared publication
Latest Publications
- Open Access
Revealing Relationship Between In Situ Impedance and Lithium Plating Onset Based on Lithium–Graphite Half-Cells
Lithium plating may occur during charging, especially at high rates or overcharging conditions for lithium-ion batteries (LIBs), which would cause battery capacity degradation and even trigger thermal runaway. Thus, it is essential to detect lithium plating onset during the charging processes. Electrochemical impedance can reveal the dynamic electrode properties of the battery, which is promising for use in battery management systems for the online detection of lithium plating onset. In this article, the impedance at 1 Hz is measured during the over-discharge and fast discharge processes using lithium–graphite half-cells. For half-cells, the variation in graphite electrode potential vs. Li/Li+ during discharging is directly recorded. An equivalent circuit model is proposed and adopted to estimate the real lithium plating reaction overpotential, which is deemed the thermodynamic indicator of lithium plating and is used as validation for the detection of lithium plating onset. Through the auxiliary validation of the estimation of lithium plating overpotential and the shape of incremental capacity curves, the relationship between impedance changes at specific frequency and the lithium plating onset is revealed. The results lay a good foundation for proposing the online diagnostic method of lithium plating onset based on the in situ impedance.
Open AccessRevealing Relationship Between In Situ Impedance and Lithium Plating Onset Based on Lithium–Graphite Half-Cells
Lithium plating may occur during charging, especially at high rates or overcharging conditions for lithium-ion batteries (LIBs), which would cause battery capacity degradation and even trigger thermal runaway. Thus, it is essential to detect lithium plating onset during the charging processes. Electrochemical impedance can reveal the dynamic electrode properties of the battery, which is promising for use in battery management systems for the online detection of lithium plating onset. In this article, the impedance at 1 Hz is measured during the over-discharge and fast discharge processes using lithium–graphite half-cells. For half-cells, the variation in graphite electrode potential vs. Li/Li+ during discharging is directly recorded. An equivalent circuit model is proposed and adopted to estimate the real lithium plating reaction overpotential, which is deemed the thermodynamic indicator of lithium plating and is used as validation for the detection of lithium plating onset. Through the auxiliary validation of the estimation of lithium plating overpotential and the shape of incremental capacity curves, the relationship between impedance changes at specific frequency and the lithium plating onset is revealed. The results lay a good foundation for proposing the online diagnostic method of lithium plating onset based on the in situ impedance.
- 4 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1255-1261
Joint Estimation of SOC and Operating Voltage of Vehicle 12V Lithium-ion Battery
Vehicle 12V lithium-ion battery is mainly used for automotive startup and low-voltage system power supply, and accurately estimate its state of charge (SOC) and operating voltage in time is essential to vehicle safety. For this, a joint estimation method for SOC and operating voltage of on-board 12V lithium-ion battery is proposed based on the second-order RC equivalent circuit model combined with the vehicle pre-charge conditions. In additional, the adaptive forgetting factor recursive least squares (AFFRLS) method is adopted to obtain circuit parameters, subsequently, double extended Kalman filter (DEKF) algorithm used to achieve SOC online estimation of 12V lithium-ion battery. Furthermore, combined with characteristic current curve under charging failure scenario, strategy for predicting the operating voltage of 12V lithium-ion battery is also proposed. Finally, a 12V 44Ah lithium-ion battery is selected to carry out the validation as proof of concept. The experimental results show that in the temperature range of 0 ℃ ~40 ℃ , the proposed joint estimation method has a maximum error of 1.6% in the SOC estimation and the accuracy of the operating voltage prediction is controlled within ±0.3%.
- 4 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1255-1261
Joint Estimation of SOC and Operating Voltage of Vehicle 12V Lithium-ion Battery
Vehicle 12V lithium-ion battery is mainly used for automotive startup and low-voltage system power supply, and accurately estimate its state of charge (SOC) and operating voltage in time is essential to vehicle safety. For this, a joint estimation method for SOC and operating voltage of on-board 12V lithium-ion battery is proposed based on the second-order RC equivalent circuit model combined with the vehicle pre-charge conditions. In additional, the adaptive forgetting factor recursive least squares (AFFRLS) method is adopted to obtain circuit parameters, subsequently, double extended Kalman filter (DEKF) algorithm used to achieve SOC online estimation of 12V lithium-ion battery. Furthermore, combined with characteristic current curve under charging failure scenario, strategy for predicting the operating voltage of 12V lithium-ion battery is also proposed. Finally, a 12V 44Ah lithium-ion battery is selected to carry out the validation as proof of concept. The experimental results show that in the temperature range of 0 ℃ ~40 ℃ , the proposed joint estimation method has a maximum error of 1.6% in the SOC estimation and the accuracy of the operating voltage prediction is controlled within ±0.3%.
- 6 March 2015
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 3 (16) , 8272-8275
The impact of the particle size of a metal–organic framework for sulfur storage in Li–S batteries
The particle size of an electrode material is known to play an essential role in its electrochemical performance in Li-ion batteries. In Li–S batteries, porous host materials are applied to store sulfur and suppress the escape of polysulfides; yet the particle size of the host as an important parameter remains largely unexplored. Herein we chose ZIF-8, a metal–organic framework (MOF) proved promising for sulfur storage, as the proof-of-concept prototype, and systematically synthesized five sets of ZIF-8 samples of different particle sizes (from 1 μm), using them as S@MOF cathodes. The results show that sulfur utilization increases monotonically with the decrease of ZIF-8 particle size (950 mA h g−1 at 0.5 C), while the best cycling stability (75% over 250 cycles at 0.5 C) is achieved with a moderate size (∼200 nm).
- 6 March 2015
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 3 (16) , 8272-8275
The impact of the particle size of a metal–organic framework for sulfur storage in Li–S batteries
The particle size of an electrode material is known to play an essential role in its electrochemical performance in Li-ion batteries. In Li–S batteries, porous host materials are applied to store sulfur and suppress the escape of polysulfides; yet the particle size of the host as an important parameter remains largely unexplored. Herein we chose ZIF-8, a metal–organic framework (MOF) proved promising for sulfur storage, as the proof-of-concept prototype, and systematically synthesized five sets of ZIF-8 samples of different particle sizes (from 1 μm), using them as S@MOF cathodes. The results show that sulfur utilization increases monotonically with the decrease of ZIF-8 particle size (950 mA h g−1 at 0.5 C), while the best cycling stability (75% over 250 cycles at 0.5 C) is achieved with a moderate size (∼200 nm).
- 9 January 2015
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 7 (4) , 2178-2182
In Situ Growth of MOFs on the Surface of Si Nanoparticles for Highly Efficient Lithium Storage: Si@MOF Nanocomposites as Anode Materials for Lithium-Ion Batteries
A simple yet powerful one-pot strategy is developed to prepare metal–organic framework-coated silicon nanoparticles via in situ mechanochemical synthesis. After simple pyrolysis, the thus-obtained composite shows exceptional electrochemical properties with a lithium storage capacity up to 1050 mA h g–1, excellent cycle stability (>99% capacity retention after 500 cycles) and outstanding rate performance. These characteristics, combined with their high stability and ease of fabrication, make such [email protected] nanocomposites ideal alternative candidates as high-energy anode materials in lithium-ion batteries.
- 9 January 2015
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 7 (4) , 2178-2182
In Situ Growth of MOFs on the Surface of Si Nanoparticles for Highly Efficient Lithium Storage: Si@MOF Nanocomposites as Anode Materials for Lithium-Ion Batteries
A simple yet powerful one-pot strategy is developed to prepare metal–organic framework-coated silicon nanoparticles via in situ mechanochemical synthesis. After simple pyrolysis, the thus-obtained composite shows exceptional electrochemical properties with a lithium storage capacity up to 1050 mA h g–1, excellent cycle stability (>99% capacity retention after 500 cycles) and outstanding rate performance. These characteristics, combined with their high stability and ease of fabrication, make such [email protected] nanocomposites ideal alternative candidates as high-energy anode materials in lithium-ion batteries.