Muthukumaran Palanisami
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Muthukumaran Palanisami has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Jeyaraj Wilson
Polymer Electronics Lab, Department of Bioelectronics and Biosensors, Alagappa University, Karaikudi, India
8 shared publications C. Sumathi
Polymer Electronics Lab, Department of Bioelectronics and Biosensors, Alagappa University, Karaikudi-630004, India
6 shared publicationsG. Ravi
Photonic Crystals Lab, Department of Physics, Alagappa University, Karaikudi-630004, India
5 shared publications- Chikkili Venkateswara Raju
Madanapalle Inst Technol & Sci, Angallu, India
2 shared publications P. Thivya
Polymer Electronics Lab, Department of Bioelectronics and Biosensors, Alagappa University, Karaikudi-630004, India
2 shared publications- Palanivel Rameshthangam
Department of Nutrition and Dietetics, Science Campus, Alagappa University, Karaikudi, India
2 shared publications
Latest Publications
- Open Access
- 7 December 2024
- Published by MDPI AG in Biosensors
- Vol. 14 (12) , 600
Point-of-Care Detection of Carcinoembryonic Antigen (CEA) Using a Smartphone-Based, Label-Free Electrochemical Immunosensor with Multilayer CuONPs/CNTs/GO on a Disposable Screen-Printed Electrode
In order to identify carcinoembryonic antigen (CEA) in serum samples, an innovative smartphone-based, label-free electrochemical immunosensor was created without the need for additional labels or markers. This technology presents a viable method for on-site cancer diagnostics. The novel smartphone-integrated, label-free immunosensing platform was constructed by nanostructured materials that utilize the layer-by-layer (LBL) assembly technique, allowing for meticulous control over the interface. Detection relies on direct interactions without extra tagging agents, where ordered graphene oxide (GO), carbon nanotubes (CNTs), and copper oxide nanoparticles (CuONPs) were sequentially deposited onto a screen-printed carbon electrode (SPCE), designated as CuONPs/CNTs/GO/SPCE. This significantly amplifies the electrochemical signal, allowing for the detection of low concentrations of target molecules of CEA. The LBL approach enables the precise construction of multi-layered structures on the sensor surface, enhancing their activity and optimizing the electrochemical performance for CEA detection. These nanostructured materials serve as efficient carriers to significantly increase the surface area, conductivity, and structural support for antibody loading, thus improving the sensitivity of detection. The detection of carcinoembryonic antigen (CEA) in this electrochemical immunosensing transducer is based on a decrease in the current response of the [Fe(CN)6]3−/4− redox probes, which occurs in proportion to the amount of the immunocomplex formed on the sensor surface. Under the optimized conditions, the immunosensor exhibited good detection of CEA with a linear range of 0.1–5.0 ng mL−1 and a low detection limit of 0.08 ng mL−1. This label-free detection approach, based on signal suppression due to immunocomplex formation, is highly sensitive and efficient for measuring CEA levels in serum samples, with higher recovery ranges of 101% to 112%, enabling early cancer diagnosis. The immunosensor was successfully applied to determine CEA in serum samples. This immunosensor has several advantages, including simple fabrication, portability, rapid analysis, high selectivity and sensitivity, and good reproducibility with long-term stability over 21 days. Therefore, it has the potential for point-of-care diagnosis of lung cancer.
- 7 December 2024
- Published by MDPI AG in Biosensors
- Vol. 14 (12) , 600
Open AccessPoint-of-Care Detection of Carcinoembryonic Antigen (CEA) Using a Smartphone-Based, Label-Free Electrochemical Immunosensor with Multilayer CuONPs/CNTs/GO on a Disposable Screen-Printed Electrode
In order to identify carcinoembryonic antigen (CEA) in serum samples, an innovative smartphone-based, label-free electrochemical immunosensor was created without the need for additional labels or markers. This technology presents a viable method for on-site cancer diagnostics. The novel smartphone-integrated, label-free immunosensing platform was constructed by nanostructured materials that utilize the layer-by-layer (LBL) assembly technique, allowing for meticulous control over the interface. Detection relies on direct interactions without extra tagging agents, where ordered graphene oxide (GO), carbon nanotubes (CNTs), and copper oxide nanoparticles (CuONPs) were sequentially deposited onto a screen-printed carbon electrode (SPCE), designated as CuONPs/CNTs/GO/SPCE. This significantly amplifies the electrochemical signal, allowing for the detection of low concentrations of target molecules of CEA. The LBL approach enables the precise construction of multi-layered structures on the sensor surface, enhancing their activity and optimizing the electrochemical performance for CEA detection. These nanostructured materials serve as efficient carriers to significantly increase the surface area, conductivity, and structural support for antibody loading, thus improving the sensitivity of detection. The detection of carcinoembryonic antigen (CEA) in this electrochemical immunosensing transducer is based on a decrease in the current response of the [Fe(CN)6]3−/4− redox probes, which occurs in proportion to the amount of the immunocomplex formed on the sensor surface. Under the optimized conditions, the immunosensor exhibited good detection of CEA with a linear range of 0.1–5.0 ng mL−1 and a low detection limit of 0.08 ng mL−1. This label-free detection approach, based on signal suppression due to immunocomplex formation, is highly sensitive and efficient for measuring CEA levels in serum samples, with higher recovery ranges of 101% to 112%, enabling early cancer diagnosis. The immunosensor was successfully applied to determine CEA in serum samples. This immunosensor has several advantages, including simple fabrication, portability, rapid analysis, high selectivity and sensitivity, and good reproducibility with long-term stability over 21 days. Therefore, it has the potential for point-of-care diagnosis of lung cancer.
- 19 November 2023
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 403
Irrigation-friendly sensor to manage drought in crops through carbon-based signature volatile sensing
- 19 November 2023
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 403
Irrigation-friendly sensor to manage drought in crops through carbon-based signature volatile sensing
- 28 October 2021
- Published by Wiley in ChemPhotoChem
- Vol. 6 (2)
Nb2O5/g‐C3N4 Heterojunction Facilitates 2,5‐Diformylfuran Production via Photocatalytic Oxidation of 5‐Hydroxymethylfurfural under Direct Sunlight Irradiation
Herein, we report the enriched synthesis of 2,5‐diformylfuran (DFF) from 5‐hydroxymethylfurfural (HMF) over a Nb2O5/g‐C3N4 heterojunction under direct sunlight irradiation. The analytical characterization established the improved quality of the heterojunction compared to the original characteristics of the single photocatalysts, especially the surface properties and alignment of band edge positions, towards the control of recombination of the charge carriers for its application in the photocatalytic oxidation of HMF. Acetonitrile possessing a moderate polarity provided significant assistance in the higher HMF conversion (72 %), resulting in a 61 % wt. DFF yield and 84 % selectivity under modest reaction conditions. The result is comparatively 1.5 to 3.3 times higher than the single photocatalysts (g‐C3N4 and Nb2O5) under similar conditions, indicating the potential of the heterostructure (type‐II heterojunction) in DFF synthesis through the synergistic action of Nb2O5 and g‐C3N4 by controlling the e−–h+ pair recombination. Moreover, the heterojunction enabled selective conversion without the supply of O2 gas or oxidizing agent. The photogenerated holes (h+) played a key role in the augmented HMF conversion (based on radical trap studies), which obeyed first‐order kinetics.
- 28 October 2021
- Published by Wiley in ChemPhotoChem
- Vol. 6 (2)
Nb2O5/g‐C3N4 Heterojunction Facilitates 2,5‐Diformylfuran Production via Photocatalytic Oxidation of 5‐Hydroxymethylfurfural under Direct Sunlight Irradiation
Herein, we report the enriched synthesis of 2,5‐diformylfuran (DFF) from 5‐hydroxymethylfurfural (HMF) over a Nb2O5/g‐C3N4 heterojunction under direct sunlight irradiation. The analytical characterization established the improved quality of the heterojunction compared to the original characteristics of the single photocatalysts, especially the surface properties and alignment of band edge positions, towards the control of recombination of the charge carriers for its application in the photocatalytic oxidation of HMF. Acetonitrile possessing a moderate polarity provided significant assistance in the higher HMF conversion (72 %), resulting in a 61 % wt. DFF yield and 84 % selectivity under modest reaction conditions. The result is comparatively 1.5 to 3.3 times higher than the single photocatalysts (g‐C3N4 and Nb2O5) under similar conditions, indicating the potential of the heterostructure (type‐II heterojunction) in DFF synthesis through the synergistic action of Nb2O5 and g‐C3N4 by controlling the e−–h+ pair recombination. Moreover, the heterojunction enabled selective conversion without the supply of O2 gas or oxidizing agent. The photogenerated holes (h+) played a key role in the augmented HMF conversion (based on radical trap studies), which obeyed first‐order kinetics.
- 13 November 2019
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 43 (48) , 19397-19407
Nanocomposite based on restacked crystallites of β-NiS and Ppy for the determination of theophylline and uric acid on screen-printed electrodes
We synthesized calcinated β-NiS with a highly crystalline porous nature and mixed it with Ppy to prepare a nanocomposite, which exhibited high electrocatalytic activity and this was then used to detect theophylline and uric acid with high sensitivity and stability.
- 13 November 2019
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 43 (48) , 19397-19407
Nanocomposite based on restacked crystallites of β-NiS and Ppy for the determination of theophylline and uric acid on screen-printed electrodes
We synthesized calcinated β-NiS with a highly crystalline porous nature and mixed it with Ppy to prepare a nanocomposite, which exhibited high electrocatalytic activity and this was then used to detect theophylline and uric acid with high sensitivity and stability.
- 21 February 2018
- Published by Elsevier in Biosensors and Bioelectronics
- Vol. 108, 53-61
Electron beam-irradiated polypyrrole decorated with Bovine serum albumin pores: Simultaneous determination of epinephrine and L-tyrosine
- 21 February 2018
- Published by Elsevier in Biosensors and Bioelectronics
- Vol. 108, 53-61
Electron beam-irradiated polypyrrole decorated with Bovine serum albumin pores: Simultaneous determination of epinephrine and L-tyrosine
- 1 August 2017
- Published by Elsevier in Electrochimica Acta
- Vol. 246, 484-496
Stable and robust nanobiocomposite preparation using aminated guar gum (mimic activity of graphene) with electron beam irradiated polypyrrole and Ce-Ni bimetal: Effective role in simultaneous sensing of environmental pollutants and pseudocapacitor applications
- 1 August 2017
- Published by Elsevier in Electrochimica Acta
- Vol. 246, 484-496
Stable and robust nanobiocomposite preparation using aminated guar gum (mimic activity of graphene) with electron beam irradiated polypyrrole and Ce-Ni bimetal: Effective role in simultaneous sensing of environmental pollutants and pseudocapacitor applications
- 28 September 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (99) , 96467-96478
Enzymeless biosensor based on β-NiS@rGO/Au nanocomposites for simultaneous detection of ascorbic acid, epinephrine and uric acid
In this study, marigold flower-like self-assembled β-NiS (nickel sulfide) nanosheets were grown on rGO (reduced graphene oxide) by a single-step hydrothermal process and then gold nanospheres (AuNS) were electrochemically deposited on the β-NiS@rGO nanostructures. The β-NiS@rGO/AuNS hierarchical hybrid demonstrates excellent electrochemical activities for clinically important analytes such as AA (ascorbic acid), EP (epinephrine) and UA (uric acid) simultaneously. Moreover, the β-NiS@rGO/AuNS/GCE exhibits significant detection of AA by one order and UA by two orders higher sensitivity when compared to a β-NiS@rGO modified electrode. We investigated using this electrocatalyst for individual detection, the linear responses of AA, EP and UA at concentrations in the ranges of 900 nM to 100 μM, 2 μM to 1 mM and 100 nM to 1 mM with low detection limits of 331 nM, 540 nM and 4.5 nM (S/N = 3σ/b), respectively; the resulting non-enzymatic biosensor also retained a good response to simultaneous detection with a wide linear range 1 μM to 1 mM, 2 μM to 1 mM and 100 nM to 1 mM and significantly lower detection limits of 682 nM, 1.3 μM and 6 nM, respectively. Excellent stability, reproducibility, and selectivity were achieved. Biosensing of AA, EP and UA in human urine, blood, serum, fruits and pharmaceutical drugs was successfully demonstrated without any preliminary treatment.
- 28 September 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (99) , 96467-96478
Enzymeless biosensor based on β-NiS@rGO/Au nanocomposites for simultaneous detection of ascorbic acid, epinephrine and uric acid
In this study, marigold flower-like self-assembled β-NiS (nickel sulfide) nanosheets were grown on rGO (reduced graphene oxide) by a single-step hydrothermal process and then gold nanospheres (AuNS) were electrochemically deposited on the β-NiS@rGO nanostructures. The β-NiS@rGO/AuNS hierarchical hybrid demonstrates excellent electrochemical activities for clinically important analytes such as AA (ascorbic acid), EP (epinephrine) and UA (uric acid) simultaneously. Moreover, the β-NiS@rGO/AuNS/GCE exhibits significant detection of AA by one order and UA by two orders higher sensitivity when compared to a β-NiS@rGO modified electrode. We investigated using this electrocatalyst for individual detection, the linear responses of AA, EP and UA at concentrations in the ranges of 900 nM to 100 μM, 2 μM to 1 mM and 100 nM to 1 mM with low detection limits of 331 nM, 540 nM and 4.5 nM (S/N = 3σ/b), respectively; the resulting non-enzymatic biosensor also retained a good response to simultaneous detection with a wide linear range 1 μM to 1 mM, 2 μM to 1 mM and 100 nM to 1 mM and significantly lower detection limits of 682 nM, 1.3 μM and 6 nM, respectively. Excellent stability, reproducibility, and selectivity were achieved. Biosensing of AA, EP and UA in human urine, blood, serum, fruits and pharmaceutical drugs was successfully demonstrated without any preliminary treatment.
- 12 August 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (85) , 81500-81509
DNA mediated electrocatalytic enhancement of α-Fe2O3–PEDOT–C-MoS2hybrid nanostructures for riboflavin detection on screen printed electrode
A facile synthesis of DNA wrapped iron oxide nanorods and PEDOT (poly(3,4-ethylenedioxythiophene)) nanospheres on carbon supported MoS2(C-MoS2) is reported for riboflavin (RF) sensing.
- 12 August 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (85) , 81500-81509
DNA mediated electrocatalytic enhancement of α-Fe2O3–PEDOT–C-MoS2hybrid nanostructures for riboflavin detection on screen printed electrode
A facile synthesis of DNA wrapped iron oxide nanorods and PEDOT (poly(3,4-ethylenedioxythiophene)) nanospheres on carbon supported MoS2(C-MoS2) is reported for riboflavin (RF) sensing.
- 11 March 2016
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry B
- Vol. 4 (15) , 2561-2569
Au–Pd bimetallic nanoparticles anchored on α-Fe 2 O 3 nonenzymatic hybrid nanoelectrocatalyst for simultaneous electrochemical detection of dopamine and uric acid in the presence of ascorbic acid
We have found that magnetic α-Fe 2 O 3 nanocubes exhibit an intrinsic catalytic activity toward the electrochemical sensing of dopamine (DA) and uric acid (UA) in the presence of ascorbic acid.
- 11 March 2016
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry B
- Vol. 4 (15) , 2561-2569
Au–Pd bimetallic nanoparticles anchored on α-Fe 2 O 3 nonenzymatic hybrid nanoelectrocatalyst for simultaneous electrochemical detection of dopamine and uric acid in the presence of ascorbic acid
We have found that magnetic α-Fe 2 O 3 nanocubes exhibit an intrinsic catalytic activity toward the electrochemical sensing of dopamine (DA) and uric acid (UA) in the presence of ascorbic acid.