Eun-Sang Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Eun-Sang Lee has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
Seong-Hyun Kim
Inha Univ
4 shared publicationsJong-Koo Won
Inha University
3 shared publicationsNam-Hun Kim
School of Mechanical Engineering, Pusan National University, Kumjung-Ku, South Korea
3 shared publicationsSeung-Geon Choi
Inha Univ
3 shared publicationsWoong-Kirl Choi
Inha Univ
3 shared publicationsJ.-W. Park
Graduate School of Mechanical Engineering Division, ERC, Pusan National University, Pusan, Korea KR
2 shared publications
Latest Publications
- Open Access
A Novel Tactile Sensing System Utilizing Magnetorheological Structures for Dynamic Contraction and Relaxation Motions
It is well known that the rheological properties of magnetorheological (MR) material change under a magnetic field. So far, most works on MR materials have been oriented toward actuating characteristics instead of sensing functions. In this work, to realize dynamic tactile motion, a spherical MR structure was designed as a sensor, incorporating a magnetic circuit core to provide maximum dynamic motion. After manufacturing a prototype (sample), a sinusoidal magnetic field of varying exciting frequency and magnitude was applied to the sample, and the dynamic contraction and relaxation motion depending on the exciting magnetic field was observed. Among the test results, when 10% deformation occurred, the instantaneous force generated was from 2.8 N to 8.8 N, and the force when relaxed was from 1.2 N to 3.5 N. It is also shown that the repulsive force within this range can be implemented using an acceptable input current. The special tactile sensing structure proposed in this work can be used as a sensor to measure the field-dependent viscoelastic properties of human tissues such as stomach, liver, and overall body. In addition, it could be usefully applied to robot surgery, because it can mimic the dynamic motions of various human organs under various surgical conditions.
Open AccessA Novel Tactile Sensing System Utilizing Magnetorheological Structures for Dynamic Contraction and Relaxation Motions
It is well known that the rheological properties of magnetorheological (MR) material change under a magnetic field. So far, most works on MR materials have been oriented toward actuating characteristics instead of sensing functions. In this work, to realize dynamic tactile motion, a spherical MR structure was designed as a sensor, incorporating a magnetic circuit core to provide maximum dynamic motion. After manufacturing a prototype (sample), a sinusoidal magnetic field of varying exciting frequency and magnitude was applied to the sample, and the dynamic contraction and relaxation motion depending on the exciting magnetic field was observed. Among the test results, when 10% deformation occurred, the instantaneous force generated was from 2.8 N to 8.8 N, and the force when relaxed was from 1.2 N to 3.5 N. It is also shown that the repulsive force within this range can be implemented using an acceptable input current. The special tactile sensing structure proposed in this work can be used as a sensor to measure the field-dependent viscoelastic properties of human tissues such as stomach, liver, and overall body. In addition, it could be usefully applied to robot surgery, because it can mimic the dynamic motions of various human organs under various surgical conditions.
- Open Access
Half-Bridge Silicon Strain Gauges with Arc-Shaped Piezoresistors
Half-bridge silicon strain gauges are widely used in the fabrication of diaphragm-type high-pressure sensors, but in some applications, they suffer from low output sensitivity because of mounting position constraints. Through a special design and fabrication approach, a new half-bridge silicon strain gauge comprising one arc gauge responding to tangential strain and another linear gauge measuring radial strain was developed using Silicon-on-Glass (SiOG) substrate technology. The tangential gauge consists of grid patterns, such as the reciprocating arc of silicon piezoresistors on a thin glass substrate. When two half-bridges are connected to form a full bridge with arc-shaped gauges that respond to tangential strain, they have the advantage of providing much higher output sensitivity than a conventional half-bridge. Pressure sensors tested under pressure ranging from 0 to 50 bar at five different temperatures indicate a linear output with a typical sensitivity of approximately 16 mV/V/bar, a maximum zero shift of 0.05% FS, and a span shift of 0.03% FS. The higher output level of pressure sensing gauges will provide greater signal strength, thus maintaining a better signal-to-noise ratio than conventional pressure sensors. The offset and span shift curves are quite linear across the operating temperature range, giving the end user the advantage of using very simple algorithms for temperature compensation of offset and span shift.
Open AccessHalf-Bridge Silicon Strain Gauges with Arc-Shaped Piezoresistors
Half-bridge silicon strain gauges are widely used in the fabrication of diaphragm-type high-pressure sensors, but in some applications, they suffer from low output sensitivity because of mounting position constraints. Through a special design and fabrication approach, a new half-bridge silicon strain gauge comprising one arc gauge responding to tangential strain and another linear gauge measuring radial strain was developed using Silicon-on-Glass (SiOG) substrate technology. The tangential gauge consists of grid patterns, such as the reciprocating arc of silicon piezoresistors on a thin glass substrate. When two half-bridges are connected to form a full bridge with arc-shaped gauges that respond to tangential strain, they have the advantage of providing much higher output sensitivity than a conventional half-bridge. Pressure sensors tested under pressure ranging from 0 to 50 bar at five different temperatures indicate a linear output with a typical sensitivity of approximately 16 mV/V/bar, a maximum zero shift of 0.05% FS, and a span shift of 0.03% FS. The higher output level of pressure sensing gauges will provide greater signal strength, thus maintaining a better signal-to-noise ratio than conventional pressure sensors. The offset and span shift curves are quite linear across the operating temperature range, giving the end user the advantage of using very simple algorithms for temperature compensation of offset and span shift.
- Open Access
A Study on Electron Acceptor of Carbonaceous Materials for Highly Efficient Hydrogen Uptakes
Significant efforts have been directed toward the identification of carbonaceous materials that can be utilized for hydrogen uptake in order to develop on-board automotive systems with a gravimetric capacity of 5.5 wt.%, thus meeting the U.S. Department of Energy technical targets. However, the capacity of hydrogen storage is limited by the weak interaction between hydrogen molecules and the carbon surface. Cigarette butts, which are the most abundant form of primary plastic waste, remain an intractable environmental pollution problem. To transform this source of waste into a valuable adsorbent for hydrogen uptake, we prepared several forms of oxygen-rich cigarette butt-derived porous carbon (CGB-AC, with the activation temperature range of 600 and 900 °C). Our experimental investigation revealed that the specific surface area increased from 600 to 700 °C and then decreased as the temperature rose to 900 °C. In contrast, the oxygen contents gradually decreased with increasing activation temperature. CGB-AC700 had the highest H2 excess uptake () of 8.54 wt.% at 77 K and 20 bar, which was much higher than that of porous carbon reported in the previous studies. We found that the dynamic interaction between the porosity and the oxygen content determined the hydrogen storage capacity. The underlying mechanisms proposed in the present study would be useful in the design of efficient hydrogen storage because they explain the interaction between positive carbonaceous materials and negative hydrogen molecules in quadrupole orbitals.Open AccessA Study on Electron Acceptor of Carbonaceous Materials for Highly Efficient Hydrogen Uptakes
Significant efforts have been directed toward the identification of carbonaceous materials that can be utilized for hydrogen uptake in order to develop on-board automotive systems with a gravimetric capacity of 5.5 wt.%, thus meeting the U.S. Department of Energy technical targets. However, the capacity of hydrogen storage is limited by the weak interaction between hydrogen molecules and the carbon surface. Cigarette butts, which are the most abundant form of primary plastic waste, remain an intractable environmental pollution problem. To transform this source of waste into a valuable adsorbent for hydrogen uptake, we prepared several forms of oxygen-rich cigarette butt-derived porous carbon (CGB-AC, with the activation temperature range of 600 and 900 °C). Our experimental investigation revealed that the specific surface area increased from 600 to 700 °C and then decreased as the temperature rose to 900 °C. In contrast, the oxygen contents gradually decreased with increasing activation temperature. CGB-AC700 had the highest H2 excess uptake () of 8.54 wt.% at 77 K and 20 bar, which was much higher than that of porous carbon reported in the previous studies. We found that the dynamic interaction between the porosity and the oxygen content determined the hydrogen storage capacity. The underlying mechanisms proposed in the present study would be useful in the design of efficient hydrogen storage because they explain the interaction between positive carbonaceous materials and negative hydrogen molecules in quadrupole orbitals. - Open Access
- 30 September 2019
- Published by The Korean Electrochemical Society - English Journal in Journal of Electrochemical Science and Technology
- Vol. 10 (3) , 276-283
Prediction and Comparison of Electrochemical Machining on Shape Memory Alloy(SMA) using Deep Neural Network(DNN)
w : Neural network weight coefficient
- 30 September 2019
- Published by The Korean Electrochemical Society - English Journal in Journal of Electrochemical Science and Technology
- Vol. 10 (3) , 276-283
Open AccessPrediction and Comparison of Electrochemical Machining on Shape Memory Alloy(SMA) using Deep Neural Network(DNN)
w : Neural network weight coefficient
- Open Access
Quadrilateral Micro-Hole Array Machining on Invar Thin Film: Wet Etching and Electrochemical Fusion Machining
Ultra-precision products which contain a micro-hole array have recently shown remarkable demand growth in many fields, especially in the semiconductor and display industries. Photoresist etching and electrochemical machining are widely known as precision methods for machining micro-holes with no residual stress and lower surface roughness on the fabricated products. The Invar shadow masks used for organic light-emitting diodes (OLEDs) contain numerous micro-holes and are currently machined by a photoresist etching method. However, this method has several problems, such as uncontrollable hole machining accuracy, non-etched areas, and overcutting. To solve these problems, a machining method that combines photoresist etching and electrochemical machining can be applied. In this study, negative photoresist with a quadrilateral hole array pattern was dry coated onto 30-µm-thick Invar thin film, and then exposure and development were carried out. After that, photoresist single-side wet etching and a fusion method of wet etching-electrochemical machining were used to machine micro-holes on the Invar. The hole machining geometry, surface quality, and overcutting characteristics of the methods were studied. Wet etching and electrochemical fusion machining can improve the accuracy and surface quality. The overcutting phenomenon can also be controlled by the fusion machining. Experimental results show that the proposed method is promising for the fabrication of Invar film shadow masks.
Open AccessQuadrilateral Micro-Hole Array Machining on Invar Thin Film: Wet Etching and Electrochemical Fusion Machining
Ultra-precision products which contain a micro-hole array have recently shown remarkable demand growth in many fields, especially in the semiconductor and display industries. Photoresist etching and electrochemical machining are widely known as precision methods for machining micro-holes with no residual stress and lower surface roughness on the fabricated products. The Invar shadow masks used for organic light-emitting diodes (OLEDs) contain numerous micro-holes and are currently machined by a photoresist etching method. However, this method has several problems, such as uncontrollable hole machining accuracy, non-etched areas, and overcutting. To solve these problems, a machining method that combines photoresist etching and electrochemical machining can be applied. In this study, negative photoresist with a quadrilateral hole array pattern was dry coated onto 30-µm-thick Invar thin film, and then exposure and development were carried out. After that, photoresist single-side wet etching and a fusion method of wet etching-electrochemical machining were used to machine micro-holes on the Invar. The hole machining geometry, surface quality, and overcutting characteristics of the methods were studied. Wet etching and electrochemical fusion machining can improve the accuracy and surface quality. The overcutting phenomenon can also be controlled by the fusion machining. Experimental results show that the proposed method is promising for the fabrication of Invar film shadow masks.
- Open Access
- 31 October 2017
- Published by The Korean Society of Manufacturing Process Engineers in Journal of the Korean Society of Manufacturing Process Engineers
- Vol. 16 (5) , 141-149
A Study on the Optimal Conditions of Hole Machining of Microplate by Application of Response Surface Methodology in Wire-Pulse Electrochemical Machining
- 31 October 2017
- Published by The Korean Society of Manufacturing Process Engineers in Journal of the Korean Society of Manufacturing Process Engineers
- Vol. 16 (5) , 141-149
Open AccessA Study on the Optimal Conditions of Hole Machining of Microplate by Application of Response Surface Methodology in Wire-Pulse Electrochemical Machining
- 28 September 2017
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 31 (9) , 4345-4351
A study of the current density analysis for two type method on the invar alloy in electrochemical machining
- 28 September 2017
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 31 (9) , 4345-4351
A study of the current density analysis for two type method on the invar alloy in electrochemical machining
- 23 April 2017
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 31 (4) , 1851-1859
Comparison between wire mesh and plate electrodes during wide-pattern machining on invar fine sheet using through-mask electrochemical micromachining
- 23 April 2017
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 31 (4) , 1851-1859
Comparison between wire mesh and plate electrodes during wide-pattern machining on invar fine sheet using through-mask electrochemical micromachining
- 1 December 2016
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 40 (5) , 739-747
PULSED ELECTROCHEMICAL MICRO MACHINING OF INVAR (FE-NI) FILM USING AN ELECTRODE ARRAY
Recently, invar (Fe-Ni) material has been applied to OLED shadow masks due to its thermal change characteristics and thermal expansion coefficient. The most widely used manufacturing methods for invar are etching and laser machining, but they have problems like non-machined areas generated by etching and surface burning in laser machining. For this reason, an alternative machining method is necessary. In this study, pulsed electrochemical machining (PECM) has been applied to fabricate an OLED shadow mask. PECM is a highly promising technology for shadow mask manufacturing because it can produce micro-scale and complex tapered holes in one process. A pilot experiment was carried out to find a suitable electrolyte for invar film, and an array of coated Ti electrodes was used to fabricate micro holes.
- 1 December 2016
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 40 (5) , 739-747
PULSED ELECTROCHEMICAL MICRO MACHINING OF INVAR (FE-NI) FILM USING AN ELECTRODE ARRAY
Recently, invar (Fe-Ni) material has been applied to OLED shadow masks due to its thermal change characteristics and thermal expansion coefficient. The most widely used manufacturing methods for invar are etching and laser machining, but they have problems like non-machined areas generated by etching and surface burning in laser machining. For this reason, an alternative machining method is necessary. In this study, pulsed electrochemical machining (PECM) has been applied to fabricate an OLED shadow mask. PECM is a highly promising technology for shadow mask manufacturing because it can produce micro-scale and complex tapered holes in one process. A pilot experiment was carried out to find a suitable electrolyte for invar film, and an array of coated Ti electrodes was used to fabricate micro holes.
- 19 July 2016
- Published by Springer Nature in Microsystem Technologies
- Vol. 23 (2) , 405-410
Electrochemical micro machining characteristics of Fe64Ni36 invar film using micro WC rod electrode
- 19 July 2016
- Published by Springer Nature in Microsystem Technologies
- Vol. 23 (2) , 405-410
Electrochemical micro machining characteristics of Fe64Ni36 invar film using micro WC rod electrode