Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Johannes Brehm has a total of 12 co-authors. Here are the top co-authors by number of shared publications:

  • Andreas Jossen

    Technical University of Munich

    5 shared publications
  • Maximilian Altmann

    Bayerische Motoren Werke Aktiengesellschaft (BMW AG), Petuelring 130, 80788 Munich, Germany

    4 shared publications
  • Philip Kotter

    Bayerische Motoren Werke Aktiengesellschaft (BMW AG), Petuelring 130, 80788 Munich, Germany

    4 shared publications
  • Axel Durdel

    Chair of Electrical Energy Storage Technology, Department of Energy and Process Engineering, School of Engineering and Design, Technical University of Munich, Arcisstraße 21, 80333 Munich, Germany

    3 shared publications
  • Andreas Aufschläger

    Technical University of Munich, School of Engineering and Design, Department of Energy and Process Engineering, Chair of Electrical Energy Storage Technology, 80333 Munich, Germany

    2 shared publications
  • Lara Mehlsam

    Technical University of Munich, School of Engineering and Design, Department of Energy and Process Engineering, Chair of Electrical Energy Storage Technology, Arcisstrasse 21, 80333 Munich, Germany

    1 shared publication

Latest Publications

  • Open Access

    Temperature Dependency of Swelling Force in Prismatic Lithium-Ion Cells Under Fixed Mechanical Constraints Over Lifetime

    by Johannes Brehm, Maximilian Altmann, Lara Mehlsam, Philip Kotter, Andreas Jossen

    The performance and integrity of large-format lithium-ion cells are strongly influenced by the swelling and mechanical deformation that occurs during operation. In this study the influence of ambient temperature and cell design on the mechanical swelling stresses and degradation behavior of prismatic lithium-ion cells during cyclic aging has been investigated. Mechanical stresses were monitored in-situ during C/2 cycling at temperatures ranging from 15 °C to 45 °C for two different commercial prismatic cell types ≥ 60 Ah. Increasing temperature from 15 °C to 45 °C resulted in higher maximum stresses at end of test by factors of 1.85 and 3.69 depending on cell type. The minimum stress exhibited a bilinear trend, where the gradient correlated positively with temperature. The intercalation induced stress amplitude showed three stages: rapid initial increase, plateau, and decreasing amplitude, with higher temperatures shortening the plateau duration. However, the temperature sensitivity of mechanical stresses could not be directly attributed to differences in degradation modes but rather to capacity- and resistance-neutral effects, most likely related to solid-electrolyte interphase layer growth and electrolyte gassing. The findings from this study contribute to a better understanding of the complex interplay between temperature, mechanical stresses, and the degradation of prismatic lithium-ion cells.


  • Open Access

    Modeling Volume and Porosity Change of Lithium-Ion Cells Due to Lithium Intercalation and External Pressure

    by Axel Durdel, Johannes Brehm, Valentin Elender, Lukas Bitschnau, Andreas Aufschläger, Maximilian Altmann, Philip Kotter, Andreas Jossen

    Volume and subsequent porosity changes of lithium-ion cells during charge-discharge cycles are major challenges in the development of high-performance and long-lasting batteries. This work presents a novel coupled electrochemical-mechanical modeling approach to describe porosity changes due to intercalation and external compression. Based on the Doyle-Fuller-Newman model, the electrochemical model is extended by incorporating a mechanical model grounded in solid mechanics. The elasticity of the anode, separator, and cathode is modeled as poroelastic to account for the non-linear stress-strain behavior of these porous materials. A porosity model to calculate the local changes in porosity is introduced and discussed. The coupled model is validated against a 70.2A h cell regarding cell voltage, reversible cell swelling, and pressure increase for C-rates between C/20 and 1C, achieving a root-mean-squared error ≤12 mV in cell voltage and <7% in reversible cell swelling. Simulation studies reveal that mechanical aspects significantly impact electrochemical performance, potentially leading to earlier lithium plating. Furthermore, the mathematical formulation shows that porosity changes alone have minimal impact on performance, and that effective mass transport should be updated based on porosity changes. The model prediction regarding internal states like porosity and volume changes aligns with the literature.


  • Open Access

    Mechanical Characterization and Modeling of Large-Format Lithium-Ion Battery Cell Electrodes and Separators for Real Operating Scenarios

    by Johannes Brehm, Axel Durdel, Tobias Kussinger, Philip Kotter, Maximilian Altmann, Andreas Jossen

    This study presents a novel application-oriented approach to the mechanical characterization and subsequent modeling of porous electrodes and separators in lithium-ion cells to gain a better understanding of their real mechanical operating behavior. An experimental study was conducted on the non-linear stiffness of LiNi0.8Co0.15Al0.05O2 and graphite electrodes as well as PE separators, harvested from large-format lithium-ion cells, using compression tests. The mechanical response of the components was determined for different operating conditions, including nominal stress levels, mechanical loading rates, and mechanical cycles. The presented work describes the test procedure, the experimental setup, and an objective evaluation method, allowing for a detailed summary of the observed mechanical behavior. A distinct nominal stress level and mechanical cycle dependency of the non-linear stiffnesses of the porous materials were found. However, no clear dependency on compression rate was observed. Based on the experimental data, a poroelastic mechanical model was utilized to predict the non-linear behavior of these porous materials under real mechanical operating scenarios with a normalized root-mean-squared error less than 5.5%. The results provide essential new insights into the mechanical behavior of porous electrodes and separators in lithium-ion cells under real operating conditions, enabling the accelerated development of high-performing and safe batteries for various applications.


  • Experimental Analysis of the Mechanical Aging Behavior of Large-Format Lithium-Ion Cells Under Various Compression and Temperature Conditions

    by Johannes Brehm, Maximilian Altmann, Philip Kotter, Andreas Jossen

    Prior works with lithium-ion cells show that volume work in the active material is caused by reversible (de-)intercalation as well as irreversible degradation phenomena during cyclic aging [1, 2]. This is known to cause a change in layer thickness, porosity or both [3] and subsequently a partly irreversible volume change at prismatic full cell level [4]. These effects pose a major challenge during development of high-performance and long-lasting batteries due to the complexity of holistic modelling approaches. This study contributes to covercoming these challenges by experimentally investigating the influence of various compression and temperature levels on the mechanical aging behavior of large-format lithium-ion cells. Cyclic aging tests are conducted on 72 Ah prismatic lithium-ion cells using different mechanical boundary conditions to analyze the cell aging phenomena via their mechanical, electrochemical and thermal characteristics. The tests are designed in such a way that cells are removed sequentially from cycling that results in different states of health (SoHs). This enables subsequentially post-mortem analysis comprising mechanical, optical and electrochemical methods in order to determine degradation modes on electrode level. The test results under non-fixed mechanical boundaries suggest initial compression as a major influence on the maximum cell expansion. Increased ambient temperature accelerates the battery aging and increases the resulting forces under fixed mechanical boundaries. In addition, results of the post-mortem analysis suggest a negative correlation between layer thickness, mass loading of the anode as well as the internal gas pressure with regard to SOH. Lastly, an increase in lithium content on the anode is shown with decreasing SOH, while the content on the cathode decreases. In conclusion, this study provides insights into the mechanical aging behavior of large-format lithium-ion cells operated at various boundary conditions. Moreover, the proposed approach bridges the gap between electrochemical phenomena on electrode level with mechanical effects on full cell level. These results create the basis for multiphysical full cell modelling under different aging conditions, which will be presented in future work. References: [1] Zhu, S., Le Yang, Fan, J., Wen, J., Feng, X., Zhou, P., Xie, F., Zhou, J., and Wang, Y.-N., “In-situ obtained internal strain and pressure of the cylindrical Li-ion battery cell with silicon-graphite negative electrodes,” Journal of energy storage, vol. 42, 2021. [2] Waldmann, T., Gorse, S., Samtleben, T., Schneider, G., Knoblauch, V., and Wohlfahrt-Mehrens, M., “A Mechanical Aging Mechanism in Lithium-Ion Batteries,” Journal of The Electrochemical Society, vol. 161, no. 10, 2014. [3] Schweidler, S., Biasi, L. d., Schiele, A., Hartmann, P., Brezesinski, T., and Janek, J., “Volume Changes of Graphite Anodes Revisited: A Combined Operando X-ray Diffraction and In Situ Pressure Analysis Study,” J. Phys. Chem. C, vol. 122, no. 16, 2018. [4] Daubinger, P., Schelter, M., Petersohn, R., Nagler, F., Hartmann, S., Herrmann, M., and Giffin, G. A., “Impact of Bracing on Large Format Prismatic Lithium‐Ion Battery Cells during Aging,” Adv. Energy Mater., 2021. Figure 1

  • (Invited) Modeling the Volume and Porosity Change of Lithium-Ion Cells Due to Lithium Intercalation and External Compression

    by Axel Durdel, Johannes Brehm, Valentin Elender, Andreas Aufschläger, Maximilian Altmann, Philip Kotter, Andreas Jossen

    Active materials in lithium-ion batteries experience (de-)intercalation-induced volumetric work during cycling [1]. This volumetric work causes a change in coating thickness, porosity, or both [2]. These changes influence the effective transport pathways of lithium ions in the electrolyte, which in turn impact the electrochemical performance of the battery [3], posing a major challenge developing high-performance and long-lasting batteries. The interplay between volumetric work and external compression depends on the mechanical properties such as Young’s modulus of the anode, the separator, and the cathode. In addition, external compression during battery pack assembly with either free, fixed, or spring-loaded boundary conditions [4] must be considered, as they impact the layer thickness and porosity differently. Here, we present a novel p2D-mechanical modeling approach to predict the electrochemically induced volume change and subsequent local porosity change of lithium-ion cells under various scenarios of external compression. The model combines physics-based electrochemical processes using the Doyle-Fuller-Newman model [5] with poro-elastic mechanical deformation. The model is parametrized and fitted using experimental data obtained from approx. 5 mAh laboratory cells as well as 5 Ah pouch cells and large format 70 Ah prismatic cells. Preliminary results regarding cell voltage as well as stack thickness change are promising and show satisfying overlap with experimental data. The model predicts a reversible change in porosity during cycling of approx. 5%-points in the anode and 1.7%-points in the cathode, due to different stiffnesses and dilation behaviors of the electrodes. The decrease in anode porosity increases polarization and thus impacts the local anode potential, increasing the risk for lithium plating. Overall, the bi-directionally coupled system reveals the underlying electrochemical and mechanical interplay that leads to the volume change, which can help design novel cells structures or operating strategies like fast charge profiles, both including realistic mechanical boundary conditions. Our study demonstrates the potential of the p2D modeling approach in predicting the complex electrochemical-mechanical behavior of lithium-ion cells, which can significantly accelerate the development of high-performance and long-lasting batteries for various applications. Especially with increasing silicon content in Si/C blend anodes, the impact of volume expansion and subsequent porosity change will become ever more important to account for in future. References: [1] Franz B. Spingler et al., Electrochemically Stable In-Situ Dilatometry of NMC, NCA and Graphite Electrodes for Lithium-Ion Cells Compared to XRD Measurements (2021), Journal of The Electrochemical Society, Vol. 168 040515 [2] Parthasarathy M. Gomadam and John W. Weidner, Modeling Volume Changes in Porous Electrodes (2005), Journal of The Electrochemical Society, Vol. 153 A179 [3] Sara Taslimi Taleghani et al., A Study on The Effect of Porosity and Particles Size Distribution on Li-Ion Battery Performance (2017), Journal of The Electrochemical Society, Vol. 164 E3179 [4] Verena Müller et al., Effect of Mechanical Compression on the Aging and the Expansion Behavior of Si/C-Composite|NMC811 in Different Lithium-Ion Battery Cell Formats (2019), Journal of The Electrochemical Society, Vol. 166 A3796 [5] Marc Doyle, Thomas F. Fuller and John Newman, Modeling of Galvanostatic Charge and Discharge of the Lithium/Polymer/Insertion Cell (1993), Journal of The Electrochemical Society, Vol. 140 1526 Figure 1