Jun Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jun Liu has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Chong Tang
School of Electrical Engineering Engineering and Research Center for Integrated New Energy Photovoltaics and Energy Storage Systems of Hunan Province University of South China 421001 Hengyang Hunan China
2 shared publicationsBeirong Ye
Institute of Fundamental and Frontier Sciences, University of Electronic Science and Technology of China, Chengdu, China
1 shared publicationChen Li
1 shared publication- Chen Li
Institute of Fundamental and Frontier Sciences, University of Electronic Science and Technology of China, Chengdu, China
1 shared publication - Han Li
Southwest Institute of Technology and Engineering, Chongqing 400039, China
1 shared publication - Honglong Ning
Guangdong Basic Research Center of Excellence for Energy & Information Polymer Materials, State Key Laboratory of Luminescent Materials and Devices, School of Materials Sciences and Engineering, South China University of Technology, Guangzhou 510640, China
1 shared publication
Latest Publications
- Open Access
Pt/Al2O3 for Efficient CF4 Hydrolytic Decomposition
Tetrafluoromethane (CF4) is one of the most stable perfluorinated compounds because of its highly symmetric molecular structure and extremely strong C–F bonds. Catalytic hydrolysis provides a promising route for CF4 abatement, yet the development of efficient catalysts capable of activating C–F bonds at reduced temperatures remains challenging. Herein, Pt-modified Al2O3 catalysts were prepared to promote CF4 decomposition through the regulation of surface acidity, CF4 adsorption, and hydroxyl formation. NH3 temperature-programmed desorption revealed that Pt introduction significantly enhanced the surface acidity of Al2O3, while CF4 temperature-programmed desorption demonstrated strengthened CF4 adsorption over Pt/Al2O3. In situ infrared spectroscopy further showed that Pt incorporation promoted the generation of surface hydroxyl groups under reaction-relevant conditions. These hydroxyl species are proposed to participate in C–F bond activation during CF4 hydrolysis. As a result, Pt/Al2O3 achieved complete CF4 decomposition at 600 °C and maintained excellent stability during the long-term test, clearly outperforming pristine Al2O3. This work demonstrates that Pt/Al2O3 is an effective catalyst for CF4 decomposition by coupling enhanced acidity, improved CF4 adsorption, and hydroxyl-assisted C–F bond activation.
Open AccessPt/Al2O3 for Efficient CF4 Hydrolytic Decomposition
Tetrafluoromethane (CF4) is one of the most stable perfluorinated compounds because of its highly symmetric molecular structure and extremely strong C–F bonds. Catalytic hydrolysis provides a promising route for CF4 abatement, yet the development of efficient catalysts capable of activating C–F bonds at reduced temperatures remains challenging. Herein, Pt-modified Al2O3 catalysts were prepared to promote CF4 decomposition through the regulation of surface acidity, CF4 adsorption, and hydroxyl formation. NH3 temperature-programmed desorption revealed that Pt introduction significantly enhanced the surface acidity of Al2O3, while CF4 temperature-programmed desorption demonstrated strengthened CF4 adsorption over Pt/Al2O3. In situ infrared spectroscopy further showed that Pt incorporation promoted the generation of surface hydroxyl groups under reaction-relevant conditions. These hydroxyl species are proposed to participate in C–F bond activation during CF4 hydrolysis. As a result, Pt/Al2O3 achieved complete CF4 decomposition at 600 °C and maintained excellent stability during the long-term test, clearly outperforming pristine Al2O3. This work demonstrates that Pt/Al2O3 is an effective catalyst for CF4 decomposition by coupling enhanced acidity, improved CF4 adsorption, and hydroxyl-assisted C–F bond activation.
- Open Access
- 2 December 2025
- Published by OAE Publishing Inc. in Energy Materials
- Vol. 5 (4)
Plasma-engineered sandwich-structured N-doped carbon@TiNb 2 O 7 with vertical graphene skeletons for ultrahigh-rate and long-cycling lithium storage
The rapid expansion and booming development of the lithium-ion battery market have raised escalating concerns over safety issues. Titanium niobium oxide (TiNb2O7, TNO) is a highly promising, safe anode material due to its intercalation reaction mechanism and high operating potential. However, its intrinsic low electronic conductivity severely hinders practical implementation. To address this, we developed a plasma-assisted interfacial engineering strategy to fabricate self-supported sandwich-structured N-doped carbon (N-C)@TNO composites. This unique “conductive skeleton || active core || protective shell” architecture comprises: (1) vertical graphene (VG) arrays acting as three-dimensional charge highways, (2) TNO nanoparticles (30-60 nm) serving as redox-active centers, and (3) uniform N-C shells (~3 nm). The synergistic coupling between the VG skeleton and the N-C coating establishes an all-around conductive network. The optimized N-C@TNO anode delivers exceptional rate capability (300.1 mAh g-1 at 0.2 C and 214.4 mAh g-1 at 40 C) and ultralong cycling stability (95.38% capacity retention after 5,000 cycles at 20 C), outperforming most reported TNO-based anodes. This work presents a novel concept for designing high-power storage electrodes, particularly multistage composite structures.
- 2 December 2025
- Published by OAE Publishing Inc. in Energy Materials
- Vol. 5 (4)
Open AccessPlasma-engineered sandwich-structured N-doped carbon@TiNb 2 O 7 with vertical graphene skeletons for ultrahigh-rate and long-cycling lithium storage
The rapid expansion and booming development of the lithium-ion battery market have raised escalating concerns over safety issues. Titanium niobium oxide (TiNb2O7, TNO) is a highly promising, safe anode material due to its intercalation reaction mechanism and high operating potential. However, its intrinsic low electronic conductivity severely hinders practical implementation. To address this, we developed a plasma-assisted interfacial engineering strategy to fabricate self-supported sandwich-structured N-doped carbon (N-C)@TNO composites. This unique “conductive skeleton || active core || protective shell” architecture comprises: (1) vertical graphene (VG) arrays acting as three-dimensional charge highways, (2) TNO nanoparticles (30-60 nm) serving as redox-active centers, and (3) uniform N-C shells (~3 nm). The synergistic coupling between the VG skeleton and the N-C coating establishes an all-around conductive network. The optimized N-C@TNO anode delivers exceptional rate capability (300.1 mAh g-1 at 0.2 C and 214.4 mAh g-1 at 40 C) and ultralong cycling stability (95.38% capacity retention after 5,000 cycles at 20 C), outperforming most reported TNO-based anodes. This work presents a novel concept for designing high-power storage electrodes, particularly multistage composite structures.
- 22 September 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (11) , 10181-10189
Self-supported MoO2/Ni Heterostructures as Highly Efficient Electrocatalysts for Alkaline Hydrogen Evolution Reaction
- 22 September 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (11) , 10181-10189
Self-supported MoO2/Ni Heterostructures as Highly Efficient Electrocatalysts for Alkaline Hydrogen Evolution Reaction
- Open Access
- 30 November 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (12) , 1465
Application of Solution-Processed High-Entropy Metal Oxide Dielectric Layers with High Dielectric Constant and Wide Bandgap in Thin-Film Transistors
High-k metal oxides are gradually replacing the traditional SiO2 dielectric layer in the new generation of electronic devices. In this paper, we report the production of five-element high entropy metal oxides (HEMOs) dielectric films by solution method and analyzed the role of each metal oxide in the system by characterizing the film properties. On this basis, we found optimal combination of (AlGaTiYZr)Ox with the best dielectric properties, exhibiting a low leakage current of 1.2 × 10−8 A/cm2 @1 MV/cm and a high dielectric constant, while the film’s visible transmittance is more than 90%. Based on the results of factor analysis, we increased the dielectric constant up to 52.74 by increasing the proportion of TiO2 in the HEMOs and maintained a large optical bandgap (>5 eV). We prepared thin film transistors (TFTs) based on an (AlGaTiYZr)Ox dielectric layer and an InGaZnOx (IGZO) active layer, and the devices exhibit a mobility of 18.2 cm2/Vs, a threshold voltage (Vth) of −0.203 V, and an subthreshold swing (SS) of 0.288 V/dec, along with a minimal hysteresis, which suggests a good prospect of applying HEMOs to TFTs. It can be seen that the HEMOs dielectric films prepared based on the solution method can combine the advantages of various high-k dielectrics to obtain better film properties. Moreover, HEMOs dielectric films have the advantages of simple processing, low-temperature preparation, and low cost, which are expected to be widely used as dielectric layers in new flexible, transparent, and high-performance electronic devices in the future.
- 30 November 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (12) , 1465
Open AccessApplication of Solution-Processed High-Entropy Metal Oxide Dielectric Layers with High Dielectric Constant and Wide Bandgap in Thin-Film Transistors
High-k metal oxides are gradually replacing the traditional SiO2 dielectric layer in the new generation of electronic devices. In this paper, we report the production of five-element high entropy metal oxides (HEMOs) dielectric films by solution method and analyzed the role of each metal oxide in the system by characterizing the film properties. On this basis, we found optimal combination of (AlGaTiYZr)Ox with the best dielectric properties, exhibiting a low leakage current of 1.2 × 10−8 A/cm2 @1 MV/cm and a high dielectric constant, while the film’s visible transmittance is more than 90%. Based on the results of factor analysis, we increased the dielectric constant up to 52.74 by increasing the proportion of TiO2 in the HEMOs and maintained a large optical bandgap (>5 eV). We prepared thin film transistors (TFTs) based on an (AlGaTiYZr)Ox dielectric layer and an InGaZnOx (IGZO) active layer, and the devices exhibit a mobility of 18.2 cm2/Vs, a threshold voltage (Vth) of −0.203 V, and an subthreshold swing (SS) of 0.288 V/dec, along with a minimal hysteresis, which suggests a good prospect of applying HEMOs to TFTs. It can be seen that the HEMOs dielectric films prepared based on the solution method can combine the advantages of various high-k dielectrics to obtain better film properties. Moreover, HEMOs dielectric films have the advantages of simple processing, low-temperature preparation, and low cost, which are expected to be widely used as dielectric layers in new flexible, transparent, and high-performance electronic devices in the future.