Xiaoqing Wei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiaoqing Wei has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Xinping Li
2 shared publicationsYi Luo
2 shared publications- Bang Ouyang
School of Electronic Information and Electrical Engineering, Shanghai Jiao Tong University, Shanghai, China
1 shared publication - Chun-Chao Chen
School of Materials Science and Engineering Shanghai Jiao Tong University Shanghai P. R. China
1 shared publication Dengxing Qu
1 shared publicationFanghua Qin
Wuhan University,School of Electrical and Automation,Wuhan,China
1 shared publication
Latest Publications
- 7 November 2024
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 43 (9) , 1605-1619
Effect of chemical consolidation on physico-mechanical properties of porous coral reef limestone
- 7 November 2024
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 43 (9) , 1605-1619
Effect of chemical consolidation on physico-mechanical properties of porous coral reef limestone
- 28 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 36 1, 1-6
An Adaptive Droop Control Scheme Based on Sliding Mode Control for Parallel Buck Converters in Low-Voltage DC Microgrids
Droop control is a widely used method in DC microgrid to solve the problem of the current sharing errors. However, it is difficult to trade off the current sharing errors and bus voltage deviation in parallel converters microgrids. This paper designs an improved droop control scheme based on adaptive droop control and sliding mode control (SMC). The droop coefficient is adjusted adaptively by proportional integral (PI) control loop to minimize the current sharing errors and the bus voltage deviation is compensated adaptively by another PI control loop, through the acquisition of the bus voltage and current. Moreover, the SMC is used to control the output voltage of each converter instantaneously. Finally, a simulation model of three parallel buck converters is built based on MATLAB/Simulink, which verifies the feasibility and effectiveness of the designed scheme in this paper. This scheme only needs power lines to transmit data, which reduces the communication burden. It is suitable and reliable for small and medium-sized DC microgrid.
- 28 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 36 1, 1-6
An Adaptive Droop Control Scheme Based on Sliding Mode Control for Parallel Buck Converters in Low-Voltage DC Microgrids
Droop control is a widely used method in DC microgrid to solve the problem of the current sharing errors. However, it is difficult to trade off the current sharing errors and bus voltage deviation in parallel converters microgrids. This paper designs an improved droop control scheme based on adaptive droop control and sliding mode control (SMC). The droop coefficient is adjusted adaptively by proportional integral (PI) control loop to minimize the current sharing errors and the bus voltage deviation is compensated adaptively by another PI control loop, through the acquisition of the bus voltage and current. Moreover, the SMC is used to control the output voltage of each converter instantaneously. Finally, a simulation model of three parallel buck converters is built based on MATLAB/Simulink, which verifies the feasibility and effectiveness of the designed scheme in this paper. This scheme only needs power lines to transmit data, which reduces the communication burden. It is suitable and reliable for small and medium-sized DC microgrid.
- 8 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Large Area and Flexible Organic Active Matrix Image Sensor Array Fabricated by Solution Coating Processes at Low Temperature
A large area and mechanically flexible active matrix image sensor array is made by integrating organic photo diode (OPDs) onto a high resolution organic thin-film transistor (OTFT) backplane on plastic substrate. The maximum process temperature is less than 100 °C. The sensor array has an imaging area of 130 mm × 130 mm and resolution of 1536 ×1536 (~300 ppi), which, to our best knowledge, is a state-of-the-art result among all reported all organic active matrix image sensor arrays.
- 8 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Large Area and Flexible Organic Active Matrix Image Sensor Array Fabricated by Solution Coating Processes at Low Temperature
A large area and mechanically flexible active matrix image sensor array is made by integrating organic photo diode (OPDs) onto a high resolution organic thin-film transistor (OTFT) backplane on plastic substrate. The maximum process temperature is less than 100 °C. The sensor array has an imaging area of 130 mm × 130 mm and resolution of 1536 ×1536 (~300 ppi), which, to our best knowledge, is a state-of-the-art result among all reported all organic active matrix image sensor arrays.