Wenda Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wenda Wu has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Guang Yang
Chemical Sciences Division, Oak Ridge National Laboratory, Oak Ridge, USA
9 shared publications - Chanho Kim
Chemical Sciences Division Oak Ridge National Laboratory Oak Ridge Tennessee USA
3 shared publications - Cheng-Tien Hsieh
School of Chemical and Biomolecular Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332, USA
3 shared publications Michelle Lehmann
3 shared publications- Nian Liu
Georgia Institute of Technology
3 shared publications - Yuanshun Li
Chemical Sciences Division Oak Ridge National Laboratory Oak Ridge TN 37831 USA
3 shared publications
Latest Publications
- Open Access
- 14 October 2026
- Published by Elsevier in SSRN Electronic Journal
Toward Reproducible Membrane Benchmarking for Vanadium Redox Flow Batteries: Conditioning, Measurement, and Implications for Manufacturing Consistency
Reliable characterization of proton-exchange membranes is essential for redox flow batteries (RFBs), yet reported properties depend on pretreatment and measurement conditions. Here, Nafion N115 and N117 serve as model systems to examine how acid activation and test configuration influence measured properties and cell performance. Untreated membranes and membranes treated with HCl, H₂SO₄, or HNO₃ were evaluated using Raman spectroscopy, ion-exchange capacity (IEC), hydration and swelling measurements, through-plane and in-plane ionic conductivity, small-angle X-ray scattering (SAXS), and vanadium RFB testing. Pretreatment produced no major changes in Raman signatures within measurement sensitivity, but bulk properties differed substantially. IEC values were similar across membranes, whereas conductivity depended on acid treatment, transport direction, and compression pressure. Water uptake and swelling were not fully correlated, and both membranes exhibited anisotropic swelling. SAXS revealed smaller water-domain spacing and a stronger matrix response in N115, particularly after acid treatment. Measured property changes did not consistently translate into improved cell performance. These findings motivate a minimum-information framework incorporating material identity, complete conditioning history, measurement state, uncertainty, and cell protocol to support reproducible membrane benchmarking.
- 14 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessToward Reproducible Membrane Benchmarking for Vanadium Redox Flow Batteries: Conditioning, Measurement, and Implications for Manufacturing Consistency
Reliable characterization of proton-exchange membranes is essential for redox flow batteries (RFBs), yet reported properties depend on pretreatment and measurement conditions. Here, Nafion N115 and N117 serve as model systems to examine how acid activation and test configuration influence measured properties and cell performance. Untreated membranes and membranes treated with HCl, H₂SO₄, or HNO₃ were evaluated using Raman spectroscopy, ion-exchange capacity (IEC), hydration and swelling measurements, through-plane and in-plane ionic conductivity, small-angle X-ray scattering (SAXS), and vanadium RFB testing. Pretreatment produced no major changes in Raman signatures within measurement sensitivity, but bulk properties differed substantially. IEC values were similar across membranes, whereas conductivity depended on acid treatment, transport direction, and compression pressure. Water uptake and swelling were not fully correlated, and both membranes exhibited anisotropic swelling. SAXS revealed smaller water-domain spacing and a stronger matrix response in N115, particularly after acid treatment. Measured property changes did not consistently translate into improved cell performance. These findings motivate a minimum-information framework incorporating material identity, complete conditioning history, measurement state, uncertainty, and cell protocol to support reproducible membrane benchmarking.
- Open Access
- 27 June 2026
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 20 (27) , 19401-19409
Suppressing Polysulfide Crossover in Sodium Polysulfide Redox-Flow Batteries with an Oxyanion-Functionalized Glass Fiber Separator
Sodium polysulfide nonaqueous redox-flow batteries are promising candidates for grid-scale energy storage due to their high theoretical energy density and earth-abundant components. However, their performance is fundamentally limited by severe polysulfide shuttling and unstable sodium-metal interfaces, particularly under high-concentration catholyte conditions. Here, we report a scalable and perfluoroalkyl-substances-free membrane modification strategy via a simple dip-coating method to fabricate commercial glass fiber (GF) with poly(4-styrenesulfonic acid-co-maleic acid) sodium salt (PSSMA). The sulfonate and carboxylate functional groups in PSSMA provide both electrostatic and steric repulsion against polysulfide anions, while preserving the mechanical flexibility of the GF substrate. The optimized PSSMA-GF membrane significantly suppresses shuttle current, mitigates self-discharge, and delays the formation of short-chain, less soluble polysulfide species, leading to improved Coulombic efficiency (from -2. This work demonstrates an environmentally benign, cost-effective, and easily scalable membrane fabrication strategy, offering a practical pathway to overcome key challenges in sodium polysulfide redox-flow batteries and other advanced energy storage systems.
- 27 June 2026
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 20 (27) , 19401-19409
Open AccessSuppressing Polysulfide Crossover in Sodium Polysulfide Redox-Flow Batteries with an Oxyanion-Functionalized Glass Fiber Separator
Sodium polysulfide nonaqueous redox-flow batteries are promising candidates for grid-scale energy storage due to their high theoretical energy density and earth-abundant components. However, their performance is fundamentally limited by severe polysulfide shuttling and unstable sodium-metal interfaces, particularly under high-concentration catholyte conditions. Here, we report a scalable and perfluoroalkyl-substances-free membrane modification strategy via a simple dip-coating method to fabricate commercial glass fiber (GF) with poly(4-styrenesulfonic acid-co-maleic acid) sodium salt (PSSMA). The sulfonate and carboxylate functional groups in PSSMA provide both electrostatic and steric repulsion against polysulfide anions, while preserving the mechanical flexibility of the GF substrate. The optimized PSSMA-GF membrane significantly suppresses shuttle current, mitigates self-discharge, and delays the formation of short-chain, less soluble polysulfide species, leading to improved Coulombic efficiency (from -2. This work demonstrates an environmentally benign, cost-effective, and easily scalable membrane fabrication strategy, offering a practical pathway to overcome key challenges in sodium polysulfide redox-flow batteries and other advanced energy storage systems.
- Open Access
- 17 June 2026
- Published by Wiley in Small Structures
- Vol. 7 (6)
An Organic Carboxylate Host for Stable Sodium Metal Batteries
Sodium metal batteries (SMBs) hold great promise for the development of high‐energy, sustainable energy storage solutions, but their practical deployment is hampered by unstable solid electrolyte interphases, uncontrollable sodium dendrite growth, and low Coulombic efficiency (CE) during repeated Na plating/stripping cycles. To address these challenges, we introduce an organic interlayer, containing perylenetetracarboxylic dianhydride sodium salt (Na 4 PT), on the surface of Cu current collector. This interlayer forms a sodiophilic organic interphase that lowers the nucleation barriers for sodium deposition and guides the formation of the interphase through polar carbonyl/carboxylate sites and a π ‐conjugated organic framework. A dendrite‐free sodium metal anode is achieved using Na 4 PT coated Cu current collector. Under capacity‐limited Na plating/stripping, Na||Na 4 PT@Cu half‐cells deliver reversible capacities of 500 and 1,000 mAh g −1 at 0.1 and 1 A g −1 for 500 cycles with average CE above 99%. Post‐cycling scanning electron microscopy and X‐ray photoelectron spectroscopy measurements confirm that Na 4 PT@Cu promotes compact and uniform Na deposits and supports the formation of a stable interphase with reduced parasitic decomposition, directly correlating interfacial chemistry/morphology with high plating/stripping reversibility. These results highlight organic carboxylate coating as a practical interface engineering strategy for dendrite‐free SMBs.
- 17 June 2026
- Published by Wiley in Small Structures
- Vol. 7 (6)
Open AccessAn Organic Carboxylate Host for Stable Sodium Metal Batteries
Sodium metal batteries (SMBs) hold great promise for the development of high‐energy, sustainable energy storage solutions, but their practical deployment is hampered by unstable solid electrolyte interphases, uncontrollable sodium dendrite growth, and low Coulombic efficiency (CE) during repeated Na plating/stripping cycles. To address these challenges, we introduce an organic interlayer, containing perylenetetracarboxylic dianhydride sodium salt (Na 4 PT), on the surface of Cu current collector. This interlayer forms a sodiophilic organic interphase that lowers the nucleation barriers for sodium deposition and guides the formation of the interphase through polar carbonyl/carboxylate sites and a π ‐conjugated organic framework. A dendrite‐free sodium metal anode is achieved using Na 4 PT coated Cu current collector. Under capacity‐limited Na plating/stripping, Na||Na 4 PT@Cu half‐cells deliver reversible capacities of 500 and 1,000 mAh g −1 at 0.1 and 1 A g −1 for 500 cycles with average CE above 99%. Post‐cycling scanning electron microscopy and X‐ray photoelectron spectroscopy measurements confirm that Na 4 PT@Cu promotes compact and uniform Na deposits and supports the formation of a stable interphase with reduced parasitic decomposition, directly correlating interfacial chemistry/morphology with high plating/stripping reversibility. These results highlight organic carboxylate coating as a practical interface engineering strategy for dendrite‐free SMBs.
- Open Access
- 5 June 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (11) , 110512
Binder-Stabilized Carbon Fiber Hosts for High-Utilization Sodium–Polysulfide Flow Catholytes
Sodium-sulfur (Na-S) batteries hold promise as high-energy-density batteries for long-duration energy storage due to their high open circuit voltage and Earth-abundant active materials. However, low utilization of the sulfur active material limits the achievable specific capacity, especially when a liquid polysulfide catholyte is utilized. High-surface-area carbon materials demonstrate promise to increase sulfur utilization in a Na-S battery. To make the carbon host material applicable for a flow battery application, a binder is required to bind the carbon materials together and to a porous substrate. Here, we utilize a composite carbon paper electrode coated by polymer,carbon nanofibers (CNFs) and carbon black (CB). By varying the mass ratios of CNF to CB, we found that a 70/20/10 mass ratio of CNF/CB/binder provided the highest capacity (260 mAh g −1 compared to the baseline of 156 mAh g −1 ) and stable battery performance over 100 cycles. Analysis of the composite electrode and full cells reveals that the amount of CB in the composite electrode influences binder distribution, cell resistance, and full cell performance.
- 5 June 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (11) , 110512
Open AccessBinder-Stabilized Carbon Fiber Hosts for High-Utilization Sodium–Polysulfide Flow Catholytes
Sodium-sulfur (Na-S) batteries hold promise as high-energy-density batteries for long-duration energy storage due to their high open circuit voltage and Earth-abundant active materials. However, low utilization of the sulfur active material limits the achievable specific capacity, especially when a liquid polysulfide catholyte is utilized. High-surface-area carbon materials demonstrate promise to increase sulfur utilization in a Na-S battery. To make the carbon host material applicable for a flow battery application, a binder is required to bind the carbon materials together and to a porous substrate. Here, we utilize a composite carbon paper electrode coated by polymer,carbon nanofibers (CNFs) and carbon black (CB). By varying the mass ratios of CNF to CB, we found that a 70/20/10 mass ratio of CNF/CB/binder provided the highest capacity (260 mAh g −1 compared to the baseline of 156 mAh g −1 ) and stable battery performance over 100 cycles. Analysis of the composite electrode and full cells reveals that the amount of CB in the composite electrode influences binder distribution, cell resistance, and full cell performance.
- 20 March 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (42)
Cation‐Diffusive Carbon Interlayers Stabilize Na Metal and Double the Current in Na‐S Redox‐Flow Batteries for Grid‐Scale Energy Storage
The sodium‐sulfur nonaqueous redox‐flow batteries (Na‐S NARFBs) using earth‐abundant elements are highly attractive due to the low material cost and improved energy density for grid‐scale energy storage. However, the low current performance, poor Na 0 /Na + redox kinetics, and Na dendrite growth pose severe challenges. We introduce cation‐diffusive layers (CDLs): thin and Na + affinitive interlayers at the Na anode that direct Na + transport and stabilize Na deposition. Benchmarking three archetypal materials—carbon paper (CP), glass microfiber paper (GF), and foam—across Na‐Na and Na‐Cu, and Na‐S cells identifies CP as the optimum. CP reduces symmetric cell overpotential by more than 70%, achieves 98% Na plating‐stripping efficiency, and doubles the Na‐S cell current density from 0.5 to 1.0 mA cm −2 without sacrificing capacity or efficiency. Ex situ electrochemical and SEM/XPS analysis, combined with molecular dynamics (MD) studies, reveal that electron‐rich carbon fibers disperse supporting salt aggregates, enrich near‐surface Na + density, and create ion transport pathways for fast Na 0 /Na + exchange while mitigating membrane degradation. Because of the ion‐centric mechanism, CDLs can be generalized to other metal‐anode designs. Further, this work establishes CDL design rules—cationic affinity and appropriate micro/nanostructure—as a simple, scalable route to high‐current, durable metal‐anode flow batteries.
- 20 March 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (42)
Cation‐Diffusive Carbon Interlayers Stabilize Na Metal and Double the Current in Na‐S Redox‐Flow Batteries for Grid‐Scale Energy Storage
The sodium‐sulfur nonaqueous redox‐flow batteries (Na‐S NARFBs) using earth‐abundant elements are highly attractive due to the low material cost and improved energy density for grid‐scale energy storage. However, the low current performance, poor Na 0 /Na + redox kinetics, and Na dendrite growth pose severe challenges. We introduce cation‐diffusive layers (CDLs): thin and Na + affinitive interlayers at the Na anode that direct Na + transport and stabilize Na deposition. Benchmarking three archetypal materials—carbon paper (CP), glass microfiber paper (GF), and foam—across Na‐Na and Na‐Cu, and Na‐S cells identifies CP as the optimum. CP reduces symmetric cell overpotential by more than 70%, achieves 98% Na plating‐stripping efficiency, and doubles the Na‐S cell current density from 0.5 to 1.0 mA cm −2 without sacrificing capacity or efficiency. Ex situ electrochemical and SEM/XPS analysis, combined with molecular dynamics (MD) studies, reveal that electron‐rich carbon fibers disperse supporting salt aggregates, enrich near‐surface Na + density, and create ion transport pathways for fast Na 0 /Na + exchange while mitigating membrane degradation. Because of the ion‐centric mechanism, CDLs can be generalized to other metal‐anode designs. Further, this work establishes CDL design rules—cationic affinity and appropriate micro/nanostructure—as a simple, scalable route to high‐current, durable metal‐anode flow batteries.
- Open Access
- 1 January 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
Manifold learning and clustering of spatially resolved high-dimensional Raman spectra for surface heterogeneity analysis of polymer solid-state electrolytes
Uniform manifold approximation and projection (UMAP) coupled with clustering allows for fast and unsupervised segmentation of high-dimensional datasets, here used to compare the surface chemistries based on spatially-resolved Raman spectra.
- 1 January 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
Open AccessManifold learning and clustering of spatially resolved high-dimensional Raman spectra for surface heterogeneity analysis of polymer solid-state electrolytes
Uniform manifold approximation and projection (UMAP) coupled with clustering allows for fast and unsupervised segmentation of high-dimensional datasets, here used to compare the surface chemistries based on spatially-resolved Raman spectra.
- Open Access
- 26 June 2025
- Published by American Chemical Society (ACS) in JACS Au
- Vol. 5 (7) , 3513-3520
Unveiling the Reactivity of Fluoropolymers with Sodium Metal: Mechanistic Insights and Battery Implications
Poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) has broad applications across various metal-ion battery systems, such as a binder for electrodes, a supporting matrix for electrolytes, and a separator material. Due to its excellent mechanical properties, PVDF-HFP has become an excellent candidate for fabricating gel and solid-state electrolytes in sodium-based batteries. However, in this study, we noticed notable side reactions occurring at the interface of PVDF-HFP membranes and Na metal. These reactions not only alter chemical compositions but also further affect the surface morphology and adhesive properties of membranes. Similar phenomena are observed in other polyfluoroalkyl-based membranes (PVDF and PTFE). Therefore, we systematically studied the reaction mechanisms between the Na metal and these polymers. The influence of different functional groups (−F, −CF3, −H) and their arrangement on the reaction extent has also been discussed. Finally, we concluded with the key factors driving these side reactions and provided new perspectives for designing polymers tailored for sodium-based batteries.
- 26 June 2025
- Published by American Chemical Society (ACS) in JACS Au
- Vol. 5 (7) , 3513-3520
Open AccessUnveiling the Reactivity of Fluoropolymers with Sodium Metal: Mechanistic Insights and Battery Implications
Poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) has broad applications across various metal-ion battery systems, such as a binder for electrodes, a supporting matrix for electrolytes, and a separator material. Due to its excellent mechanical properties, PVDF-HFP has become an excellent candidate for fabricating gel and solid-state electrolytes in sodium-based batteries. However, in this study, we noticed notable side reactions occurring at the interface of PVDF-HFP membranes and Na metal. These reactions not only alter chemical compositions but also further affect the surface morphology and adhesive properties of membranes. Similar phenomena are observed in other polyfluoroalkyl-based membranes (PVDF and PTFE). Therefore, we systematically studied the reaction mechanisms between the Na metal and these polymers. The influence of different functional groups (−F, −CF3, −H) and their arrangement on the reaction extent has also been discussed. Finally, we concluded with the key factors driving these side reactions and provided new perspectives for designing polymers tailored for sodium-based batteries.
- 8 November 2024
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 9 (12) , 5795-5800
Optimizing Nonaqueous Sodium–Polysulfide Redox-Flow Batteries: The Role of Solvation Effects with Glyme Solvents
- 8 November 2024
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 9 (12) , 5795-5800
Optimizing Nonaqueous Sodium–Polysulfide Redox-Flow Batteries: The Role of Solvation Effects with Glyme Solvents
- 25 October 2024
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 12 (1) , 119-130
Effects of catholyte aging on high-nickel NMC cathodes in sulfide all-solid-state batteries
Unlocking longevity in solid-state batteries: our study highlights how the sulfide catholyte Li 6 PS 5 Cl outshines halide-based alternatives by mitigating side reactions in NMC811 cathodes, indicating its promise for extending battery lifespan.
- 25 October 2024
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 12 (1) , 119-130
Effects of catholyte aging on high-nickel NMC cathodes in sulfide all-solid-state batteries
Unlocking longevity in solid-state batteries: our study highlights how the sulfide catholyte Li 6 PS 5 Cl outshines halide-based alternatives by mitigating side reactions in NMC811 cathodes, indicating its promise for extending battery lifespan.