Sayee Srikarah Volaity
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sayee Srikarah Volaity has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Narayanan Neithalath
School of Sustainable Engineering and the Built Environment, Arizona State University, Tempe, AZ, USA
4 shared publications Aditya Kumar
3 shared publicationsShubham Agrawal
School of Sustainable Engineering and the Built Environment
3 shared publications- Aditya Kumar
Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO, USA
2 shared publications Narayanan Neithalath
Arizona State Univ
2 shared publicationsRanjith Divigalpitiya
HydroGraph
2 shared publications
Latest Publications
- 1 February 2027
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Design and Construction Practice
- Vol. 32 (1)
Use of Ultralow Dosages of Graphene to Enhance the Microstructural and Mechanical Properties of 3D-Printed Cementitious Mortars
Three-dimensional (3D) concrete printing offers an economical and sustainable option for rapid, formwork-free construction of geometrically unique structures. However, 3D-printed concrete elements often suffer from print-induced anisotropy and reduced mechanical performance. This study investigates the use of two novel graphene derivatives—fractal graphene (FG) and reactive graphene (RG)—as multifunctional nano-modifiers to overcome the aforementioned limitations associated with 3D-printed concrete. The influence of ultralow dosages (0.02% by mass of binder) of FG and RG on early-age heat release in graphene-modified pastes and the porosity and direction-dependent mechanical properties of 3D-printed elements are reported. FG and RG accelerate early hydration kinetics, with RG inducing a more pronounced shift in the acceleration peak due to its functionalized surfaces. Significant reductions in total porosity and critical pore diameter are noticed. Enhancements of up to 25% in compressive and flexural strengths are observed. The anisotropy in compressive strength is shown to be reduced by up to 50% through the use of FG or RG, indicating improved structural homogeneity. The graphene-modified specimens also exhibit enhanced strain capacity and improved crack-bridging behavior. These findings demonstrate the ability of ultralow dosages of FG and RG to simultaneously enhance hydration, refine microstructure, and improve mechanical properties of 3D-printed cementitious materials.
- 1 February 2027
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Design and Construction Practice
- Vol. 32 (1)
Use of Ultralow Dosages of Graphene to Enhance the Microstructural and Mechanical Properties of 3D-Printed Cementitious Mortars
Three-dimensional (3D) concrete printing offers an economical and sustainable option for rapid, formwork-free construction of geometrically unique structures. However, 3D-printed concrete elements often suffer from print-induced anisotropy and reduced mechanical performance. This study investigates the use of two novel graphene derivatives—fractal graphene (FG) and reactive graphene (RG)—as multifunctional nano-modifiers to overcome the aforementioned limitations associated with 3D-printed concrete. The influence of ultralow dosages (0.02% by mass of binder) of FG and RG on early-age heat release in graphene-modified pastes and the porosity and direction-dependent mechanical properties of 3D-printed elements are reported. FG and RG accelerate early hydration kinetics, with RG inducing a more pronounced shift in the acceleration peak due to its functionalized surfaces. Significant reductions in total porosity and critical pore diameter are noticed. Enhancements of up to 25% in compressive and flexural strengths are observed. The anisotropy in compressive strength is shown to be reduced by up to 50% through the use of FG or RG, indicating improved structural homogeneity. The graphene-modified specimens also exhibit enhanced strain capacity and improved crack-bridging behavior. These findings demonstrate the ability of ultralow dosages of FG and RG to simultaneously enhance hydration, refine microstructure, and improve mechanical properties of 3D-printed cementitious materials.
- Open Access
- 1 January 2027
- Published by Royal Society of Chemistry (RSC) in RSC Mechanochemistry
Processing energy-based evaluation of structural evolution in kaolinite and montmorillonite standards during mechano-chemical activation
Kinematic modeling, validated against measured milling power and energy, tracks structural and reactivity evolution in two clay minerals, yielding an efficiency index for designing energy-lean mechano-chemical processes.
- 1 January 2027
- Published by Royal Society of Chemistry (RSC) in RSC Mechanochemistry
Open AccessProcessing energy-based evaluation of structural evolution in kaolinite and montmorillonite standards during mechano-chemical activation
Kinematic modeling, validated against measured milling power and energy, tracks structural and reactivity evolution in two clay minerals, yielding an efficiency index for designing energy-lean mechano-chemical processes.
- 12 December 2024
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 210
A low-carbon approach for lime production using self-propagating high temperature synthesis-driven limestone calcination
- 12 December 2024
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 210
A low-carbon approach for lime production using self-propagating high temperature synthesis-driven limestone calcination
- 26 November 2024
- Published by Elsevier in Cement and Concrete Composites
- Vol. 156
Rheology and early-age structure development in binary and ternary blends modified with novel graphene types
- 26 November 2024
- Published by Elsevier in Cement and Concrete Composites
- Vol. 156
Rheology and early-age structure development in binary and ternary blends modified with novel graphene types