Peng Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Peng Chen has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Ruibang Sun
School of Safety Science
5 shared publications - Liyang Li
School of Emergency Management and Safety Engineering, China University of Mining and Technology (Beijing) , Beijing 100083 , China
4 shared publications - Congling Shi
School of Emergency Management and Safety Engineering, China University of Mining and Technology (Beijing) , Beijing 100083 , China
3 shared publications Liyang Li
School of Emergency Management and Safety Engineering, ChinUniversity of Mining and Technology (Beijing), Beijing, China
3 shared publications- Ruibang Sun
School of Emergency Management and, Safety Engineering, China University of Mining and, Technology (Beijing) , Beijing 100083 , China
3 shared publications Xing Yang
School of Emergency Management and Safety Engineering, China University of Mining and Technology (Beijing), Beijing, China
3 shared publications
Latest Publications
- 28 February 2023
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 45 (1) , 1937-1951
Experimental study on continuous spill fire of liquid fuel on porous bed
As a traditional fossil fuel, petroleum fuel is prone to spills and fire accidents during storage, transportation, and use, which poses a great threat to the safe utilization of energy. This work aims to study the effect of porous media on the combustion characteristics of continuous spill fires. The transformer oil spill fire experiment is carried out on a porous bed with a length of 120 cm, a width of 15 cm, and a depth of 5 cm. The effects of sand diameter (0.75 mm, 1.5 mm, 3 mm, and 6 mm) and discharge rates (25 ml/min, 50 ml/min, and 75 ml/min) on the development of spill fires are analyzed. The results show that the spill fire fuel transport mechanism mainly includes gas phase diffusion caused by fuel consumption on the surface of a porous bed and liquid phase convection caused by capillary flow. Thus, three zones are formed from top to bottom: (i) the top vapor zone; (ii) the middle gas–liquid two-phase zone; and (iii) the bottom liquid phase zone. The presence of sand reduces the efficiency of the heat and mass. And it makes the spill fire stable combustion area increase compared with the smooth substrate. The stable combustion area has a positive correlation with the mass discharge rate and a negative correlation with the sand size. The stable combustion area of 1.5 mm, 3 mm, and 6 mm sand is 87.1%, 81.9%, and 77.5% of that of the 0.75 mm sand. In contrast to transformer oil pool fires and spill fires on smooth substrates, the burning rate is negatively related to the equivalent burning diameter. Meanwhile, the burning rate of spill fire on porous beds is significantly reduced compared with the first two. Based on the analysis of heat and mass transfer, a model for the burning rate of spill fire in porous media is formed and its correctness is verified. The experimental results are of great significance to the safe utilization of liquid energy.
- 28 February 2023
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 45 (1) , 1937-1951
Experimental study on continuous spill fire of liquid fuel on porous bed
As a traditional fossil fuel, petroleum fuel is prone to spills and fire accidents during storage, transportation, and use, which poses a great threat to the safe utilization of energy. This work aims to study the effect of porous media on the combustion characteristics of continuous spill fires. The transformer oil spill fire experiment is carried out on a porous bed with a length of 120 cm, a width of 15 cm, and a depth of 5 cm. The effects of sand diameter (0.75 mm, 1.5 mm, 3 mm, and 6 mm) and discharge rates (25 ml/min, 50 ml/min, and 75 ml/min) on the development of spill fires are analyzed. The results show that the spill fire fuel transport mechanism mainly includes gas phase diffusion caused by fuel consumption on the surface of a porous bed and liquid phase convection caused by capillary flow. Thus, three zones are formed from top to bottom: (i) the top vapor zone; (ii) the middle gas–liquid two-phase zone; and (iii) the bottom liquid phase zone. The presence of sand reduces the efficiency of the heat and mass. And it makes the spill fire stable combustion area increase compared with the smooth substrate. The stable combustion area has a positive correlation with the mass discharge rate and a negative correlation with the sand size. The stable combustion area of 1.5 mm, 3 mm, and 6 mm sand is 87.1%, 81.9%, and 77.5% of that of the 0.75 mm sand. In contrast to transformer oil pool fires and spill fires on smooth substrates, the burning rate is negatively related to the equivalent burning diameter. Meanwhile, the burning rate of spill fire on porous beds is significantly reduced compared with the first two. Based on the analysis of heat and mass transfer, a model for the burning rate of spill fire in porous media is formed and its correctness is verified. The experimental results are of great significance to the safe utilization of liquid energy.
- 27 December 2022
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 196 (14) , 3095-3119
Experimental Investigation on Formation Mechanism of Jet Fires in Transformer Oil Filled Equipment with External Thermal Load
Liquid jet fire was one of the typical fires that endangered industrial safety. Especially, the oil-filled equipment of the substation was subjected to an external thermal load, which caused liquid jet fire. However, less literature was available for the formation mechanism of liquid jet flame. Thus, this paper conducted a systematic experiment to reveal the formation mechanism of transformer oil jet fire with various heat release rates (33 kW, 73 kW, 132 kW, and 212 kW). In this paper, the formation mechanism of transformer oil jet fire was clarified. Experimental observation showed that the formation process of transformer oil jet fire can be divided into three stages. The gas–liquid two-phase flow occurred during the formation of transformer oil jet fire. The correlation between the overpressure peak and the heat release rate was established. The medium thermal response behavior can be divided into three stages. When the medium temperature reached the boiling point, the jet fire appeared. The thermal stratification model of a transformer oil jet was established. The correlation between the degree of liquid stratification and dimensionless heat release rate was established. The thermal convection and radiation determined the heat transfer mechanism of oil during the formation of jet fire.
- 27 December 2022
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 196 (14) , 3095-3119
Experimental Investigation on Formation Mechanism of Jet Fires in Transformer Oil Filled Equipment with External Thermal Load
Liquid jet fire was one of the typical fires that endangered industrial safety. Especially, the oil-filled equipment of the substation was subjected to an external thermal load, which caused liquid jet fire. However, less literature was available for the formation mechanism of liquid jet flame. Thus, this paper conducted a systematic experiment to reveal the formation mechanism of transformer oil jet fire with various heat release rates (33 kW, 73 kW, 132 kW, and 212 kW). In this paper, the formation mechanism of transformer oil jet fire was clarified. Experimental observation showed that the formation process of transformer oil jet fire can be divided into three stages. The gas–liquid two-phase flow occurred during the formation of transformer oil jet fire. The correlation between the overpressure peak and the heat release rate was established. The medium thermal response behavior can be divided into three stages. When the medium temperature reached the boiling point, the jet fire appeared. The thermal stratification model of a transformer oil jet was established. The correlation between the degree of liquid stratification and dimensionless heat release rate was established. The thermal convection and radiation determined the heat transfer mechanism of oil during the formation of jet fire.
- 6 December 2022
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 145 (4) , 1-11
The Burning Characteristics of Transformer Oil Spill Fire on Horizontal and Inclined Substrate Under Continuous Leakage Condition
Spill fire is a typical fire type that endangers industrial safety. This work systematically investigates the burning characteristics of transformer oil spill fire under different fuel leakage rates and substrate tilt angles, and the fuel flow hydrodynamic parameters. According to the flame spread behavior and substrate temperature distribution, the spill fire spread process is divided into four stages and the substrate is divided into three zones. The relative difference between max burning length and stable burning length is positively correlated with the substrate tilt angle. The increase of fuel flow velocity contributes to the flame spread velocity, but the increase of fuel flow velocity and the decrease of fuel layer thickness weaken the accelerating effect of surface flow on flame spread, which leads to a decreasing trend of flame spread velocity increase. The spill fire mass burning rate is 0.161–0.358 times of pool fire, and the increase of heat loss due to fuel flow and the radiant heat loss through the fuel layer dissipated through the substrate are the main reasons for the lower mass burning rate than pool fire. The research results provide basic data and references for further research on the formation mechanism of heavy oil spill fire and the prevention and control of small-scale spill fire.
- 6 December 2022
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 145 (4) , 1-11
The Burning Characteristics of Transformer Oil Spill Fire on Horizontal and Inclined Substrate Under Continuous Leakage Condition
Spill fire is a typical fire type that endangers industrial safety. This work systematically investigates the burning characteristics of transformer oil spill fire under different fuel leakage rates and substrate tilt angles, and the fuel flow hydrodynamic parameters. According to the flame spread behavior and substrate temperature distribution, the spill fire spread process is divided into four stages and the substrate is divided into three zones. The relative difference between max burning length and stable burning length is positively correlated with the substrate tilt angle. The increase of fuel flow velocity contributes to the flame spread velocity, but the increase of fuel flow velocity and the decrease of fuel layer thickness weaken the accelerating effect of surface flow on flame spread, which leads to a decreasing trend of flame spread velocity increase. The spill fire mass burning rate is 0.161–0.358 times of pool fire, and the increase of heat loss due to fuel flow and the radiant heat loss through the fuel layer dissipated through the substrate are the main reasons for the lower mass burning rate than pool fire. The research results provide basic data and references for further research on the formation mechanism of heavy oil spill fire and the prevention and control of small-scale spill fire.
- 20 July 2022
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 145 (2)
Experimental Observation of Premixed Methane/Air Flame Propagation in an Obstructed Tube With Increasing Blockage Ratios
Methane explosion is one of the major hazards in the mechanical industry. In this paper, a series of methane/air premixed combustion experiments were carried out to study the influence of blockage ratio on flame propagation. The blocking ratio (BR) is referred as the cross-sectional area of occlusion divided by the total area. Flame shape and pressure response were measured and analyzed. The results showed that five typical stages were experienced for all configurations except for BR = 0.999, particularly, a diamond-shaped flame and a mushroom-shaped flame front were observed for some lower BRs. The largest length of jet flames was selected to characterize flame–obstacle interaction rose smoothly until BR = 0.9 and then declines rapidly. The flame evolution process was simulated by a power-law flame wrinkling model. Flame behaviors and pressure dynamics for each configuration were investigated, and the maximum flame speed, explosion pressure, and growth rate coincide exactly with the largest length of jet flames in trend. It can be seen that BR was of great significance to flame propagation and BR = 0.9 was a limit or a watershed. In addition, the pressure growth rate was positively correlated with the flame tip speed.
- 20 July 2022
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 145 (2)
Experimental Observation of Premixed Methane/Air Flame Propagation in an Obstructed Tube With Increasing Blockage Ratios
Methane explosion is one of the major hazards in the mechanical industry. In this paper, a series of methane/air premixed combustion experiments were carried out to study the influence of blockage ratio on flame propagation. The blocking ratio (BR) is referred as the cross-sectional area of occlusion divided by the total area. Flame shape and pressure response were measured and analyzed. The results showed that five typical stages were experienced for all configurations except for BR = 0.999, particularly, a diamond-shaped flame and a mushroom-shaped flame front were observed for some lower BRs. The largest length of jet flames was selected to characterize flame–obstacle interaction rose smoothly until BR = 0.9 and then declines rapidly. The flame evolution process was simulated by a power-law flame wrinkling model. Flame behaviors and pressure dynamics for each configuration were investigated, and the maximum flame speed, explosion pressure, and growth rate coincide exactly with the largest length of jet flames in trend. It can be seen that BR was of great significance to flame propagation and BR = 0.9 was a limit or a watershed. In addition, the pressure growth rate was positively correlated with the flame tip speed.
- 27 June 2022
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 144 (12) , 1-11
Flame Spread Pulsation Characteristics of Transformer Oil Vertical Spill Fire
To investigate the effects of fuel discharge rate and initial fuel temperature on flame pulsation characteristics of vertical spill fire, a series of experiments under continuous leakage conditions are conducted on a specially designed experimental setup, for which transformer oil is selected as the fuel. Results show that the vertical spill fire burning area can be divided into three parts. Both the main flame and the flash flame are involved in the flame pulsation behavior, and the essence of the flame pulsation of the vertical spill fire is the periodic alternation of the diffusion flame and the premixed flame. Flame pulsation frequency shows a linear negative correlation with the fuel leakage rate, it decreases from 3.56 Hz (4.98 ml m−1s−1) to 2.439 Hz (15.93 ml m−1s−1), and it has a positive correlation with the initial fuel temperature. As the fuel discharge rate increases, the pulsation amplitude increases while the flame transient spread rate decreases, both of them have no significant correlation with the initial fuel temperature. The ratio of the average flame pulsation amplitude to the maximum pulsation amplitude is between 0.57 and 0.76. The flame transient spread rate shows a negative correlation with the fuel discharge rate, the maximum flame spread velocity reaches 3.17 m/s and 2.85 m/s in the growing phase and shrinking phase respectively. Due to the entrainment effect of the flame plume, the flame transient spread rate in the shrinking phase is higher than that in the growing phase. Analyzed the diffusion process of fuel vapor and the heat transfer mechanism of vertical spill fire, the control of fuel leakage rate and initial temperature on the flame pulsation characteristics is mainly manifested in its influence on the fuel evaporation and diffusion process and the length of preheating area. This work provides data supplement on the flame spread of liquid fuel spill fire.
- 27 June 2022
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 144 (12) , 1-11
Flame Spread Pulsation Characteristics of Transformer Oil Vertical Spill Fire
To investigate the effects of fuel discharge rate and initial fuel temperature on flame pulsation characteristics of vertical spill fire, a series of experiments under continuous leakage conditions are conducted on a specially designed experimental setup, for which transformer oil is selected as the fuel. Results show that the vertical spill fire burning area can be divided into three parts. Both the main flame and the flash flame are involved in the flame pulsation behavior, and the essence of the flame pulsation of the vertical spill fire is the periodic alternation of the diffusion flame and the premixed flame. Flame pulsation frequency shows a linear negative correlation with the fuel leakage rate, it decreases from 3.56 Hz (4.98 ml m−1s−1) to 2.439 Hz (15.93 ml m−1s−1), and it has a positive correlation with the initial fuel temperature. As the fuel discharge rate increases, the pulsation amplitude increases while the flame transient spread rate decreases, both of them have no significant correlation with the initial fuel temperature. The ratio of the average flame pulsation amplitude to the maximum pulsation amplitude is between 0.57 and 0.76. The flame transient spread rate shows a negative correlation with the fuel discharge rate, the maximum flame spread velocity reaches 3.17 m/s and 2.85 m/s in the growing phase and shrinking phase respectively. Due to the entrainment effect of the flame plume, the flame transient spread rate in the shrinking phase is higher than that in the growing phase. Analyzed the diffusion process of fuel vapor and the heat transfer mechanism of vertical spill fire, the control of fuel leakage rate and initial temperature on the flame pulsation characteristics is mainly manifested in its influence on the fuel evaporation and diffusion process and the length of preheating area. This work provides data supplement on the flame spread of liquid fuel spill fire.
- Open Access
- 22 June 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (26) , 22969-22976
Experimental Investigation of the Combustion Behavior of Transformer Oil Jet Flame
Transformer oil jet fire is one of the most dangerous types of fires in substations. The combustion behavior of transformer oil jet fire produces uncontrollable hazards to personnel and equipment and even triggers a domino effect. However, the jet fire combustion behavior of such materials as transformer oil has not been revealed before. Investigation of the combustion behavior of transformer oil jet fire has positive implications for the prevention and control of substation fires. In this paper, KI25X transformer oil was used as fuel. A series of transformer oil jet fire experiments were conducted with variable orifice diameters (5, 10, and 15 mm) with heat release rates ranging from 200 to 659.2 kW. The results showed that the entrainment coefficient of transformer oil jet fire was greater than that of pure gas phase jet fire. The entrainment coefficient of transformer oil jet fire was 0.029. Using dimensionless theory, it was proposed that the imaginary point source was proportional to the 0.317 power of Froude number. Based on the point source model, a dimensional analysis model with Reynolds number was developed. The radiation fraction of transformer oil jet fire was proportional to the -0.133 power of Reynolds number. This study played an important role in improving the jet combustion behavior of transformer oil.
- 22 June 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (26) , 22969-22976
Open AccessExperimental Investigation of the Combustion Behavior of Transformer Oil Jet Flame
Transformer oil jet fire is one of the most dangerous types of fires in substations. The combustion behavior of transformer oil jet fire produces uncontrollable hazards to personnel and equipment and even triggers a domino effect. However, the jet fire combustion behavior of such materials as transformer oil has not been revealed before. Investigation of the combustion behavior of transformer oil jet fire has positive implications for the prevention and control of substation fires. In this paper, KI25X transformer oil was used as fuel. A series of transformer oil jet fire experiments were conducted with variable orifice diameters (5, 10, and 15 mm) with heat release rates ranging from 200 to 659.2 kW. The results showed that the entrainment coefficient of transformer oil jet fire was greater than that of pure gas phase jet fire. The entrainment coefficient of transformer oil jet fire was 0.029. Using dimensionless theory, it was proposed that the imaginary point source was proportional to the 0.317 power of Froude number. Based on the point source model, a dimensional analysis model with Reynolds number was developed. The radiation fraction of transformer oil jet fire was proportional to the -0.133 power of Reynolds number. This study played an important role in improving the jet combustion behavior of transformer oil.
- 18 December 2021
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 195 (9) , 2240-2257
Experimental and Theoretical Research on the Radiative Heat Transfer Characteristics of Transformer Oil Jet Flame
In this paper, a series of transformer oil jet fire experiments with different tanks of inner diameters (0.05 m/0.08 m/0.1 m), different filling rate (80%/100%) and different pool diameters (0.3 m/0.4 m) were carried out to study the radiation characteristics of transformer oil jet fire. The flame combustion characteristics such as the fire plume temperature, mass loss and radiant heat flux were measured and analyzed. The experimental results showed that: The shape of the transformer oil jet fire was approximately cylindrical. The radiant heat flux increased exponentially with the increased of flame height. And radiant heat flux decreased exponentially as the horizontal distance increased. The multi-point source model and the line source model performed well in the prediction of the fire radiant heat flux of the transformer oil jet. As the Froude number increased, the radiation fraction change could be divided into two stages. In the first stage, the radiation fraction maintained almost constant. In the second stage, the radiation fraction dropped significantly. The research results provided valuable data support for the fire protection design of substation equipment. In addition, it could effectively improve the fire prevention and control ability of substation personnel.
- 18 December 2021
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 195 (9) , 2240-2257
Experimental and Theoretical Research on the Radiative Heat Transfer Characteristics of Transformer Oil Jet Flame
In this paper, a series of transformer oil jet fire experiments with different tanks of inner diameters (0.05 m/0.08 m/0.1 m), different filling rate (80%/100%) and different pool diameters (0.3 m/0.4 m) were carried out to study the radiation characteristics of transformer oil jet fire. The flame combustion characteristics such as the fire plume temperature, mass loss and radiant heat flux were measured and analyzed. The experimental results showed that: The shape of the transformer oil jet fire was approximately cylindrical. The radiant heat flux increased exponentially with the increased of flame height. And radiant heat flux decreased exponentially as the horizontal distance increased. The multi-point source model and the line source model performed well in the prediction of the fire radiant heat flux of the transformer oil jet. As the Froude number increased, the radiation fraction change could be divided into two stages. In the first stage, the radiation fraction maintained almost constant. In the second stage, the radiation fraction dropped significantly. The research results provided valuable data support for the fire protection design of substation equipment. In addition, it could effectively improve the fire prevention and control ability of substation personnel.
- Open Access
- 16 November 2021
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 6 (47) , 31843-31853
Experimental Research on the Combustion Characteristics of Transformer Oil Jet Fires in Oil-Filled Equipment under Heat
- 16 November 2021
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 6 (47) , 31843-31853
Open AccessExperimental Research on the Combustion Characteristics of Transformer Oil Jet Fires in Oil-Filled Equipment under Heat
- 26 October 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (2)
Numerical simulation of flame acceleration and DDT(deflagration to detonation transition) in hydrogen-air mixtures with concentration gradients
In this paper, a coupled new solver is used to simulate the acceleration and deflagration to detonation transition (DDT) of inhomogeneous mixtures flame under obstacle conditions. Analyzed the variations of flame front, pressure and density with time. The experimental results show that the vertical concentration gradient affects the chemical reaction rate in the combustion reaction zone, resulting in the flame front stretching along the “front up-back down.” At the same time, the flame propagation velocity is affected by obstacles. After multi-stage “acceleration-deceleration,” it reaches 2700 m/s at 1.23 m from the ignition center, and the pressure jumps to 5.0 MPa. Finally, the transition from detonation to detonation is completed. It is worth noting that the local explosion point is in the corner of the obstacle or pipe wall. This simulation method is compatible with low Mach number laminar flow, turbulent flow, and compressible reaction flow problems under high Mach number. It provides prospective prediction for flame acceleration and detonation formation during hydrogen combustion and detonation engine operation.
- 26 October 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (2)
Numerical simulation of flame acceleration and DDT(deflagration to detonation transition) in hydrogen-air mixtures with concentration gradients
In this paper, a coupled new solver is used to simulate the acceleration and deflagration to detonation transition (DDT) of inhomogeneous mixtures flame under obstacle conditions. Analyzed the variations of flame front, pressure and density with time. The experimental results show that the vertical concentration gradient affects the chemical reaction rate in the combustion reaction zone, resulting in the flame front stretching along the “front up-back down.” At the same time, the flame propagation velocity is affected by obstacles. After multi-stage “acceleration-deceleration,” it reaches 2700 m/s at 1.23 m from the ignition center, and the pressure jumps to 5.0 MPa. Finally, the transition from detonation to detonation is completed. It is worth noting that the local explosion point is in the corner of the obstacle or pipe wall. This simulation method is compatible with low Mach number laminar flow, turbulent flow, and compressible reaction flow problems under high Mach number. It provides prospective prediction for flame acceleration and detonation formation during hydrogen combustion and detonation engine operation.
- 17 September 2021
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 144 (1) , 1-11
Experimental Study on Horizontal Fire Spread Characteristics of Transformer Oil
In order to study the horizontal fire spread characteristics of transformer oil, a series of experiments were carried out on the experimental platform developed, the influence of the initial temperature and the width of the oil pool on the flame propagation, including the propagation speed, flame morphology and the temperature field distribution of the gas-liquid two-phase, was analyzed to reveal the flame propagation characteristics and the oil surface temperature rise law in the process of transformer oil fire propagation, and a theoretical model of coupled liquid-phase convective heat transfer and flame radiation heat transfer was established by combining thermodynamic theory to quantitatively calculate the heat transfer process of surface flow in flame propagation process. Through the theoretical analysis and quantitative calculation of gas-liquid heat transfer, it is proved that the surface flow is mainly driven by surface tension and the flame spreads in the form of pulsation. Combined with the experimental data for verification, it is found that the proportion of liquid-phase convective heat transfer to the total heat flow is much larger than that of flame radiation to the total heat flow, which proves that liquid-phase convective heat transfer is the main mode of surface flow heat transfer.
- 17 September 2021
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 144 (1) , 1-11
Experimental Study on Horizontal Fire Spread Characteristics of Transformer Oil
In order to study the horizontal fire spread characteristics of transformer oil, a series of experiments were carried out on the experimental platform developed, the influence of the initial temperature and the width of the oil pool on the flame propagation, including the propagation speed, flame morphology and the temperature field distribution of the gas-liquid two-phase, was analyzed to reveal the flame propagation characteristics and the oil surface temperature rise law in the process of transformer oil fire propagation, and a theoretical model of coupled liquid-phase convective heat transfer and flame radiation heat transfer was established by combining thermodynamic theory to quantitatively calculate the heat transfer process of surface flow in flame propagation process. Through the theoretical analysis and quantitative calculation of gas-liquid heat transfer, it is proved that the surface flow is mainly driven by surface tension and the flame spreads in the form of pulsation. Combined with the experimental data for verification, it is found that the proportion of liquid-phase convective heat transfer to the total heat flow is much larger than that of flame radiation to the total heat flow, which proves that liquid-phase convective heat transfer is the main mode of surface flow heat transfer.