Evgeniy Ivanov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Evgeniy Ivanov has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Nickolay Zagirov
Siberian Federal University, Krasnoyarsk Region, Krasnoyarsk, Russian Federation
3 shared publications - Yuri Nikolaevich Loginov
Ural Federal University, Ekaterinburg, Russian Federation
2 shared publications - Aleksandr Innokentyevich Bezrukikh
Siberian Federal University
1 shared publication - Ekaterina S. Lopatina1 shared publication
- Mikhail V. Chukin
Nosov Magnitogorsk State Technical University
1 shared publication Rinat Rizakhanov
Siberian Federal University, 79, Svobodny pr., Krasnoyarsk, Russia
1 shared publication
Latest Publications
- 25 December 2025
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 23 (4)
Research on the Technology for Producing Wire from Aluminum 1580 Alloy Chip Waste for Use in Additive Manufacturing
The development of new technologies for the manufacture of long-length deformed semi-finished products from recycled aluminum alloy waste, which exclude melting conversion during their implementation, is an urgent task of metallurgical production. The objective of the work was to evaluate the possibility of obtaining and properties of deformed semi-finished products from chip waste of aluminum 1580 alloy. The research results on a method for producing rods and wire from chips of an experimental aluminum 1580 alloy with a scandium content of 0.12 wt. % are presented. The main methods used are powder metallurgy (briquetting), metal forming (extrusion and drawing) and heat treatment (annealing). Using the developed general technological scheme for the thermal deformation treatment of bulk aluminum alloy chip waste, experimental studies have been conducted on the technology for producing briquetted blanks and hot extruded rods with diameters of 4.9 and 6.8 mm from 1580 alloy chips. It was found that the strength of the rods after hot extrusion is characterized by values of ultimate tensile strength of 370-380 MPa, and plasticity by values of elongation of 18-20 %. Such a level of mechanical properties of pressed rods ensured the possibility of continuous production of wire with a diameter of 3 mm without intermediate annealing. Drawing routes of a wire with a diameter of up to 1 mm from these rods have been calculated and experimentally tested. The mechanical properties of the wire were determined, and the change in the structure of semi-finished products and pieces at all technological stages of thermal deformation treatment were studied. Research has shown that the wire obtained from 1580 alloy chips meets the requirements for welding wire made of aluminum alloys and can be used as a material for surfacing products in the implementation of additive technologies.
- 25 December 2025
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 23 (4)
Research on the Technology for Producing Wire from Aluminum 1580 Alloy Chip Waste for Use in Additive Manufacturing
The development of new technologies for the manufacture of long-length deformed semi-finished products from recycled aluminum alloy waste, which exclude melting conversion during their implementation, is an urgent task of metallurgical production. The objective of the work was to evaluate the possibility of obtaining and properties of deformed semi-finished products from chip waste of aluminum 1580 alloy. The research results on a method for producing rods and wire from chips of an experimental aluminum 1580 alloy with a scandium content of 0.12 wt. % are presented. The main methods used are powder metallurgy (briquetting), metal forming (extrusion and drawing) and heat treatment (annealing). Using the developed general technological scheme for the thermal deformation treatment of bulk aluminum alloy chip waste, experimental studies have been conducted on the technology for producing briquetted blanks and hot extruded rods with diameters of 4.9 and 6.8 mm from 1580 alloy chips. It was found that the strength of the rods after hot extrusion is characterized by values of ultimate tensile strength of 370-380 MPa, and plasticity by values of elongation of 18-20 %. Such a level of mechanical properties of pressed rods ensured the possibility of continuous production of wire with a diameter of 3 mm without intermediate annealing. Drawing routes of a wire with a diameter of up to 1 mm from these rods have been calculated and experimentally tested. The mechanical properties of the wire were determined, and the change in the structure of semi-finished products and pieces at all technological stages of thermal deformation treatment were studied. Research has shown that the wire obtained from 1580 alloy chips meets the requirements for welding wire made of aluminum alloys and can be used as a material for surfacing products in the implementation of additive technologies.
- 15 March 2021
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 23 (1) , 45-55
Evaluation of the level of hardening of aluminum alloy chips intended for subsequent pressure treatment
Introduction. It is noted that the chip is an undesirable type of metal scrap, because it has a developed surface, which creates conditions for more intense interaction with the surrounding atmosphere. This creates conditions for oxidation and gas saturation, especially at elevated temperatures typical of remelting processes. Therefore, the process of chip utilizing is considered, bypassing the remelting stage. The aim of the work is to establish the level of work hardening of chips during the processing of aluminum alloys and to predict its effect on the subsequent processing process. Research methods: to assess the deformed state, the finite element method was applied, implemented in the RAPID-2D software package. The sequence of actions included the creation of the initial shape of the deformation region and the configuration of the tool. The mutual displacement of the tool and the deformable material is specified using the corresponding boundary conditions. The deformable medium is a viscous-plastic material with power-law hardening, the physical and mechanical properties correspond to an aluminum-magnesium alloy. Results and discussion: the solution obtained shows that the degree of shear deformation in the chips can reach a value of more than 2. In this case, a higher level of deformation is localized on the side of the convex part of the chip. The comparison of the solution with those obtained earlier by other authors is carried out and its similarity is shown. In the considered solution, the difference in the degree of work-hardening of the chips along its thickness is 36 %. A variant of the sequence of processing the workpiece first by cold deformation, and then by cutting is considered. The field of application of the results of the work is the development of methods for the processing of technogenic formations. Conclusions. During the cutting process, the plastic deformation of the chips reaches significant values. In this paper, the difference in the degree of shear deformation in the chip thickness is established, depending on the proximity of the cut layer to the surface of the cutting tool. It is proposed to take this difference into account at the subsequent stages of chip processing. The presence of the marked inhomogeneity of mechanical properties leads to consequences in the form of an inhomogeneous distribution of the temperature of the beginning of recrystallization during subsequent operations of heat treatment or hot deformation treatment. The principle of additivity of the degree of deformation obtained by the metal at the stage of plastic shaping of the workpiece and the shaping of the chip itself is introduced.
- 15 March 2021
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 23 (1) , 45-55
Evaluation of the level of hardening of aluminum alloy chips intended for subsequent pressure treatment
Introduction. It is noted that the chip is an undesirable type of metal scrap, because it has a developed surface, which creates conditions for more intense interaction with the surrounding atmosphere. This creates conditions for oxidation and gas saturation, especially at elevated temperatures typical of remelting processes. Therefore, the process of chip utilizing is considered, bypassing the remelting stage. The aim of the work is to establish the level of work hardening of chips during the processing of aluminum alloys and to predict its effect on the subsequent processing process. Research methods: to assess the deformed state, the finite element method was applied, implemented in the RAPID-2D software package. The sequence of actions included the creation of the initial shape of the deformation region and the configuration of the tool. The mutual displacement of the tool and the deformable material is specified using the corresponding boundary conditions. The deformable medium is a viscous-plastic material with power-law hardening, the physical and mechanical properties correspond to an aluminum-magnesium alloy. Results and discussion: the solution obtained shows that the degree of shear deformation in the chips can reach a value of more than 2. In this case, a higher level of deformation is localized on the side of the convex part of the chip. The comparison of the solution with those obtained earlier by other authors is carried out and its similarity is shown. In the considered solution, the difference in the degree of work-hardening of the chips along its thickness is 36 %. A variant of the sequence of processing the workpiece first by cold deformation, and then by cutting is considered. The field of application of the results of the work is the development of methods for the processing of technogenic formations. Conclusions. During the cutting process, the plastic deformation of the chips reaches significant values. In this paper, the difference in the degree of shear deformation in the chip thickness is established, depending on the proximity of the cut layer to the surface of the cutting tool. It is proposed to take this difference into account at the subsequent stages of chip processing. The presence of the marked inhomogeneity of mechanical properties leads to consequences in the form of an inhomogeneous distribution of the temperature of the beginning of recrystallization during subsequent operations of heat treatment or hot deformation treatment. The principle of additivity of the degree of deformation obtained by the metal at the stage of plastic shaping of the workpiece and the shaping of the chip itself is introduced.
- Open Access
- 31 December 2020
- Published by Knowledge E DMCC in KnE Materials Science
- p. 560–566
Application of Pressure Treatment Methods for Solid Processing of Silumin Chip Waste
N this article various technological schemes for processing waste in the form of chips of an alloy of an aluminum-silicon system are presented. It was noted that the processing of fine waste of the chips type is always accompanied by oxidation of the metal due to the large surface of contact with the air. To eliminate the loss of metal into oxides during re-melting, this study proposes processing chips by pressing to obtain briquettes (a method of hot extrusion is meant by ‘pressing’). Processing involves the receipt of briquettes from rods. The processes of cold and hot briquetting were undertaken separately. The results of applying the scheme using real production waste are presented in this study. The tensile strength achieved was up to 270 MPa. The relative elongation to rupture was 10–25% and the area reduction after rupture was 25–45%. There were no large differences in the use of briquettes obtained by cold processing and hot processing. The conclusion is drawn about the overall effectiveness of the application of the waste processing without the use of the metal melting. Keywords: silumin, shavings, extrusion, plastic deformation, heat treatment
- 31 December 2020
- Published by Knowledge E DMCC in KnE Materials Science
- p. 560–566
Open AccessApplication of Pressure Treatment Methods for Solid Processing of Silumin Chip Waste
N this article various technological schemes for processing waste in the form of chips of an alloy of an aluminum-silicon system are presented. It was noted that the processing of fine waste of the chips type is always accompanied by oxidation of the metal due to the large surface of contact with the air. To eliminate the loss of metal into oxides during re-melting, this study proposes processing chips by pressing to obtain briquettes (a method of hot extrusion is meant by ‘pressing’). Processing involves the receipt of briquettes from rods. The processes of cold and hot briquetting were undertaken separately. The results of applying the scheme using real production waste are presented in this study. The tensile strength achieved was up to 270 MPa. The relative elongation to rupture was 10–25% and the area reduction after rupture was 25–45%. There were no large differences in the use of briquettes obtained by cold processing and hot processing. The conclusion is drawn about the overall effectiveness of the application of the waste processing without the use of the metal melting. Keywords: silumin, shavings, extrusion, plastic deformation, heat treatment