Guanxi Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Guanxi Zhao has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Rui Han
School of Materials Science and Engineering, Key Laboratory of Materials and Surface Technology (Ministry of Education), Engineering Research Center of Intelligent Air-Ground Integration Vehicle and Control, Xihua University, Chengdu 610039, China
3 shared publications - Wenyan Wang
Key Laboratory of Materials and Surface Technology (Ministry of Education), School of Materials Science and Engineering, Xihua University, Chengdu 610039, China
2 shared publications - Dengxun Ren
Key Laboratory of Materials and Surface Technology (Ministry of Education), School of Materials Science and Engineering, Engineering Research Center of Intelligent Air-Ground Integration Vehicle and Control, Xihua University, Chengdu 610039, China
1 shared publication - Guang-Zhao Li
Key Laboratory of Materials and Surface Technology (Ministry of Education), School of Materials Science and Engineering, Xihua University, Chengdu 610039, China
1 shared publication - Hong Jiang
School of Materials and Chemistry, University of Shanghai for Science and Technology, Shanghai, China
1 shared publication - Min Nie
Polymer Research Institute of Sichuan University
1 shared publication
Latest Publications
- Open Access
Constructing a Concentric GO Network via Rotational Extrusion for Synergistic Axial–Hoop Mechanics in Polymer Microtubes
Driven by societal and technological progress, the polymer tubing industry is increasingly focused on sustainable and biodegradable products, with polylactic acid (PLA)-based microtubes gaining attention for applications such as medical stents and disposable straws. However, their inherent mechanical limitations, especially under hoop loading and the brittleness of PLA, restrict broader use. Although two-dimensional nanofillers can enhance polymer properties, conventional extrusion only creates uniaxial alignment, leaving fillers randomly oriented in the radial plane and failing to improve hoop performance. To address this, we developed a rotational extrusion strategy that superimposes a rotational force onto the conventional axial flow, generating a biaxial stress field. By adjusting rotational speed to regulate hoop stress, a concentric, interlocked graphene oxide network in a PLA/polybutylene adipate terephthalate microtube is induced along the circumferential direction without disturbing its axial alignment. This architecturally tailored structure significantly enhances hoop mechanical properties, including high compressive strength of 0.54 MPa, excellent low-temperature impact toughness of 0.33 J, and improved bending resistance of 30 N, while maintaining axial mechanical strength exceeding 50 MPa. This work demonstrates a scalable and efficient processing route to fabricate high-performance composite microtubes with tunable and balanced directional properties, offering a viable strategy for industrial applications in medical, packaging, and structural fields.
Open AccessConstructing a Concentric GO Network via Rotational Extrusion for Synergistic Axial–Hoop Mechanics in Polymer Microtubes
Driven by societal and technological progress, the polymer tubing industry is increasingly focused on sustainable and biodegradable products, with polylactic acid (PLA)-based microtubes gaining attention for applications such as medical stents and disposable straws. However, their inherent mechanical limitations, especially under hoop loading and the brittleness of PLA, restrict broader use. Although two-dimensional nanofillers can enhance polymer properties, conventional extrusion only creates uniaxial alignment, leaving fillers randomly oriented in the radial plane and failing to improve hoop performance. To address this, we developed a rotational extrusion strategy that superimposes a rotational force onto the conventional axial flow, generating a biaxial stress field. By adjusting rotational speed to regulate hoop stress, a concentric, interlocked graphene oxide network in a PLA/polybutylene adipate terephthalate microtube is induced along the circumferential direction without disturbing its axial alignment. This architecturally tailored structure significantly enhances hoop mechanical properties, including high compressive strength of 0.54 MPa, excellent low-temperature impact toughness of 0.33 J, and improved bending resistance of 30 N, while maintaining axial mechanical strength exceeding 50 MPa. This work demonstrates a scalable and efficient processing route to fabricate high-performance composite microtubes with tunable and balanced directional properties, offering a viable strategy for industrial applications in medical, packaging, and structural fields.
- Open Access
Polyamide 6 as a Liner Material for Type IV Hydrogen Storage Cylinders: Performance Challenges and Modification Strategies
Type IV hydrogen storage cylinders are pivotal for high-pressure hydrogen storage and transportation, offering advantages such as lightweight design, high hydrogen storage density, and cost efficiency. Polyamide 6 (PA6) has emerged as a promising liner material due to its excellent mechanical strength, chemical resistance, and gas barrier properties. However, challenges remain, including high hydrogen permeability and insufficient mechanical performance under extreme temperature and pressure conditions. This review systematically summarizes recent advances in modification strategies to enhance PA6’s suitability for Type IV hydrogen storage cylinders. Incorporating nanofillers (e.g., graphene, montmorillonite, and carbon nanotubes) significantly reduces hydrogen permeability. In situ polymerization and polymer blending techniques improve toughness and interfacial adhesion (e.g., ternary blends achieve a special increase in impact strength). Multiscale structural design (e.g., biaxial stretching) and process optimization further enhance PA6’s overall performance. Future research should focus on interdisciplinary innovation, standardized testing protocols, and industry–academia collaboration to accelerate the commercialization of PA6-based composites for hydrogen storage applications. This review provides theoretical insights and engineering guidelines for developing high-performance liner materials.
Open AccessPolyamide 6 as a Liner Material for Type IV Hydrogen Storage Cylinders: Performance Challenges and Modification Strategies
Type IV hydrogen storage cylinders are pivotal for high-pressure hydrogen storage and transportation, offering advantages such as lightweight design, high hydrogen storage density, and cost efficiency. Polyamide 6 (PA6) has emerged as a promising liner material due to its excellent mechanical strength, chemical resistance, and gas barrier properties. However, challenges remain, including high hydrogen permeability and insufficient mechanical performance under extreme temperature and pressure conditions. This review systematically summarizes recent advances in modification strategies to enhance PA6’s suitability for Type IV hydrogen storage cylinders. Incorporating nanofillers (e.g., graphene, montmorillonite, and carbon nanotubes) significantly reduces hydrogen permeability. In situ polymerization and polymer blending techniques improve toughness and interfacial adhesion (e.g., ternary blends achieve a special increase in impact strength). Multiscale structural design (e.g., biaxial stretching) and process optimization further enhance PA6’s overall performance. Future research should focus on interdisciplinary innovation, standardized testing protocols, and industry–academia collaboration to accelerate the commercialization of PA6-based composites for hydrogen storage applications. This review provides theoretical insights and engineering guidelines for developing high-performance liner materials.
- 5 December 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (48) , 22073-22090
Enhanced interfacial interaction of basalt fiber/PP composites by in-situ grown ZnO nanorods: preparation, structure, property and mechanistic study
- 5 December 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (48) , 22073-22090
Enhanced interfacial interaction of basalt fiber/PP composites by in-situ grown ZnO nanorods: preparation, structure, property and mechanistic study