Adekunle Adetayo Yekini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Adekunle Adetayo Yekini has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Marcos de Oliveira Siqueira
Universidade Federal de Viçosa, Brazil
1 shared publication - Ibrahim Ademola Fetuga
Department of Mechanical Engineering, University of Lagos
1 shared publication - Julio Cesar Costa Campos
Federal University of Viçosa, Brazil
1 shared publication - Kabiru Olaiya
Lagos State University of Science and Technology
1 shared publication - Lukman Animashaun
Lagos State University of Science and Technology
1 shared publication - Olabode Thomas Olakoyejo
University of Lagos, Nigeria
1 shared publication
Latest Publications
- 31 December 2025
- Published by Echo Academic Publishing in Environmental Research and Technology
- Vol. 8 (4) , 784-791
Estimation of plastic production, consumption, and waste generation in Nigeria: 2020 to 2050
Global utilization of different types of plastics has been increasing over the years due to its many useful properties. However, disposal of plastic waste has been a challenge all over the world and Nigeria is not an exception. As the most populous country in Africa, Nigeria is among the highest consumers of plastic products. Plastic waste generation was considered using three different scenarios that considered forecasted gross domestic productions up to 2050. The results indicated that plastic production rate in Nigeria is linear as against plastic consumption rate which is exponential. The result estimates from 2020 to 2050 revealed that plastic consumption in Nigeria doubles every 9 years which was validated using the doubling time equation. However, substantial reduction was achieved if enhanced plastic waste management technologies are adopted. Further reduction is achievable through reuse or recycle and implementation of hierarchical waste management strategies.
- 31 December 2025
- Published by Echo Academic Publishing in Environmental Research and Technology
- Vol. 8 (4) , 784-791
Estimation of plastic production, consumption, and waste generation in Nigeria: 2020 to 2050
Global utilization of different types of plastics has been increasing over the years due to its many useful properties. However, disposal of plastic waste has been a challenge all over the world and Nigeria is not an exception. As the most populous country in Africa, Nigeria is among the highest consumers of plastic products. Plastic waste generation was considered using three different scenarios that considered forecasted gross domestic productions up to 2050. The results indicated that plastic production rate in Nigeria is linear as against plastic consumption rate which is exponential. The result estimates from 2020 to 2050 revealed that plastic consumption in Nigeria doubles every 9 years which was validated using the doubling time equation. However, substantial reduction was achieved if enhanced plastic waste management technologies are adopted. Further reduction is achievable through reuse or recycle and implementation of hierarchical waste management strategies.
- Open Access
- 15 October 2024
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 10 (10) , 21156
Computational Heat Transfer and Entropy Generation Analysis of Natural Convection in a Trapezoidal Cavity
A numerical study is carried out to investigate natural convective heat transfer process in a water-filled trapezoidal cavity heated from below using finite volume method in solving the governing equations. The study examined the effects of Rayleigh number (Ra = 101-106), heat source length (Ls = 0.1-0.9), angle of inclination (teta = 0º-75º) on the Nusselt number (Nu) and entropy generation of the trapezoidal cavity. The results of the investigation indicate that Nu increases when the source length increases, and the angle of inclination decreases. Also, Nu also increases with Ra when the source length and inclination angle are fixed. The total entropy is dominated by thermal entropy generation (Sthermal) and is seen to increase with source length. The results presented in isotherms and streamlines indicate that viscous and buoyancy forces are significant in the trapezoidal cavity.
- 15 October 2024
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 10 (10) , 21156
Open AccessComputational Heat Transfer and Entropy Generation Analysis of Natural Convection in a Trapezoidal Cavity
A numerical study is carried out to investigate natural convective heat transfer process in a water-filled trapezoidal cavity heated from below using finite volume method in solving the governing equations. The study examined the effects of Rayleigh number (Ra = 101-106), heat source length (Ls = 0.1-0.9), angle of inclination (teta = 0º-75º) on the Nusselt number (Nu) and entropy generation of the trapezoidal cavity. The results of the investigation indicate that Nu increases when the source length increases, and the angle of inclination decreases. Also, Nu also increases with Ra when the source length and inclination angle are fixed. The total entropy is dominated by thermal entropy generation (Sthermal) and is seen to increase with source length. The results presented in isotherms and streamlines indicate that viscous and buoyancy forces are significant in the trapezoidal cavity.