Mehmet Ahad Yurtoglu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mehmet Ahad Yurtoglu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Michael Peter
Fraunhofer HHI
3 shared publications - Ramez Askar
Fraunhofer Institute for Telecommunications, Heinrich Hertz Institute, HHI
3 shared publications Sven Wittig
Fraunhofer Institute for Telecommunications, Heinrich Hertz Institute, HHI
2 shared publicationsLaura Alice Leather
Fraunhofer Institute for Telecommunications, Heinrich Hertz Institute
1 shared publicationMathis Schmieder
Fraunhofer Institute for Telecommunications, Heinrich Hertz Institute, HHI
1 shared publication- Mathis Schmieder
Fraunhofer Institute for Telecommunications, Heinrich Hertz Institute, HHI
1 shared publication
Latest Publications
- Open Access
- 8 June 2026
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- p. 1-13
6G upper mid-band independently controllable dual-polarized reconfigurable intelligent surface (RIS)
This paper presents a novel, independently controllable dual-polarized reconfigurable intelligent surface (RIS) unit cell for 6G upper mid-band ( 7.125 $7.125$ – 24.25 GHz $24.25\,\mathrm{GHz}$ ) applications. The proposed unit cell is based on the diagonal placement of mutually orthogonal tunable radiators (loaded with varactor diodes) alongside static dual-polarized radiators. Full-wave electromagnetic simulations of the unit cell demonstrate a phase shift range of 270 ring $270^{\circ}$ , a maximum reflection loss of 4.5 dB $4.5\,\mathrm{dB}$ , and 61 dB $61\,\mathrm{dB}$ cross-polarization isolation (XPI) within a 400 MHz $400\,\mathrm{MHz}$ frequency range centered at 15 GHz $15\,\mathrm{GHz}$ . Furthermore, full-wave simulations of a 16 times 16 $16 \times 16$ RIS panel were conducted for various reflection angles under both TE- and TM-polarized illuminations. The results demonstrate a wide-angle beam-steering capability of plus or minus 60 ring $\pm60^\circ$ , with a maximum beam-pointing error of only 1.7 ring $1.7^{\circ}$ . The proposed RIS also exhibits accurate and stable reflection control under wide-angle excitation. A 3 times 3 $3 \times 3$ prototype was fabricated to validate the unit cell’s performance. Measurement results agree with the simulations, yielding a 270 ring $270^{\circ}$ phase shift, approximately 7 dB $7\,\mathrm{dB}$ reflection loss, and 24 dB $24\,\mathrm{dB}$ XPI. The proposed RIS is a promising candidate for future 6G communication systems.- 8 June 2026
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- p. 1-13
Open Access6G upper mid-band independently controllable dual-polarized reconfigurable intelligent surface (RIS)
This paper presents a novel, independently controllable dual-polarized reconfigurable intelligent surface (RIS) unit cell for 6G upper mid-band ( 7.125 $7.125$ – 24.25 GHz $24.25\,\mathrm{GHz}$ ) applications. The proposed unit cell is based on the diagonal placement of mutually orthogonal tunable radiators (loaded with varactor diodes) alongside static dual-polarized radiators. Full-wave electromagnetic simulations of the unit cell demonstrate a phase shift range of 270 ring $270^{\circ}$ , a maximum reflection loss of 4.5 dB $4.5\,\mathrm{dB}$ , and 61 dB $61\,\mathrm{dB}$ cross-polarization isolation (XPI) within a 400 MHz $400\,\mathrm{MHz}$ frequency range centered at 15 GHz $15\,\mathrm{GHz}$ . Furthermore, full-wave simulations of a 16 times 16 $16 \times 16$ RIS panel were conducted for various reflection angles under both TE- and TM-polarized illuminations. The results demonstrate a wide-angle beam-steering capability of plus or minus 60 ring $\pm60^\circ$ , with a maximum beam-pointing error of only 1.7 ring $1.7^{\circ}$ . The proposed RIS also exhibits accurate and stable reflection control under wide-angle excitation. A 3 times 3 $3 \times 3$ prototype was fabricated to validate the unit cell’s performance. Measurement results agree with the simulations, yielding a 270 ring $270^{\circ}$ phase shift, approximately 7 dB $7\,\mathrm{dB}$ reflection loss, and 24 dB $24\,\mathrm{dB}$ XPI. The proposed RIS is a promising candidate for future 6G communication systems. - 9 March 2026
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 18 (3) , 1-10
3D-printed dual-polarized magneto-electric dipole antenna with > 50-dB wideband isolation for full-duplex and ICAS applications
This study presents the development of a 3D-printed, wideband, dual-polarized magneto-electric dipole antenna. The proposed antenna demonstrates exceptional cross-polarization isolation (XPI) between its two mutually orthogonal RF ports, achieved through innovative feeding probes, specifically an inverted $\Gamma$ -shape and a conventional $\Gamma$ -shape probe. The analysis reveals that misalignment between probes can impair XPI; this phenomenon is systematically examined through electromagnetic full-wave simulations. A practical remedy is provided using four plastic rods strategically positioned through the probes and posts. Measurements indicate that XPI exceeds 50 dB across the common operating frequency range of 3.05–4.13 GHz (30%). The maximum realized gain is approximately 7.9 dBi, with a nearly flat response and stable radiation patterns across both ports throughout the bandwidth. The proposed antenna offers a cost-effective, 3D-printed design, wideband radiation performance, and exceptional port-to-port isolation, demonstrating significant potential for full-duplex wireless communication and ICAS applications.- 9 March 2026
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 18 (3) , 1-10
3D-printed dual-polarized magneto-electric dipole antenna with > 50-dB wideband isolation for full-duplex and ICAS applications
This study presents the development of a 3D-printed, wideband, dual-polarized magneto-electric dipole antenna. The proposed antenna demonstrates exceptional cross-polarization isolation (XPI) between its two mutually orthogonal RF ports, achieved through innovative feeding probes, specifically an inverted $\Gamma$ -shape and a conventional $\Gamma$ -shape probe. The analysis reveals that misalignment between probes can impair XPI; this phenomenon is systematically examined through electromagnetic full-wave simulations. A practical remedy is provided using four plastic rods strategically positioned through the probes and posts. Measurements indicate that XPI exceeds 50 dB across the common operating frequency range of 3.05–4.13 GHz (30%). The maximum realized gain is approximately 7.9 dBi, with a nearly flat response and stable radiation patterns across both ports throughout the bandwidth. The proposed antenna offers a cost-effective, 3D-printed design, wideband radiation performance, and exceptional port-to-port isolation, demonstrating significant potential for full-duplex wireless communication and ICAS applications.- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Electromagnetics, Antennas and Propagation
- Vol. 2, 504-518
6G Upper-Mid Band Independently Controllable Dual-Polarized Reconfigurable Intelligent Surface: Design, Prototyping, and Measurements
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Electromagnetics, Antennas and Propagation
- Vol. 2, 504-518
Open Access6G Upper-Mid Band Independently Controllable Dual-Polarized Reconfigurable Intelligent Surface: Design, Prototyping, and Measurements
- Open Access
- 10 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Sub-THz Waveguide Band-Pass Filter: Design, Analysis and Fabrication Repeatability
This paper presents two units of Y-band (325-500 GHz) and two units of D-band (110-170 GHz) all-pole inline Chebyshev band-pass filters (BPFs) using high-precision computer numerically controlled milling. The filters are based on six-coupled resonant cavities and are designed for a 20 dB return loss in a 10 GHz bandwidth centered around 470 GHz and 160 GHz, respectively. The filter sections are designed using the standard waveguides of the next frequency band to guarantee single-mode propagation, and taper sections are placed for the transition. Statistical analyses of the design parameters are performed to estimate the manufacturing tolerance. Microscope measurements are done and it is seen that machine tolerance on cavity lengths of about 3.5 microns causes a 2 GHz center frequency shift in Y-band. Measurements validate the analyses. The fabrication repeatability in the D-band is more consistent than in the Y-band. Indeed, two Y-band BPF units have a center frequency shift difference of 6 GHz while the the D-band BPF units have almost identical responses.
- 10 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessSub-THz Waveguide Band-Pass Filter: Design, Analysis and Fabrication Repeatability
This paper presents two units of Y-band (325-500 GHz) and two units of D-band (110-170 GHz) all-pole inline Chebyshev band-pass filters (BPFs) using high-precision computer numerically controlled milling. The filters are based on six-coupled resonant cavities and are designed for a 20 dB return loss in a 10 GHz bandwidth centered around 470 GHz and 160 GHz, respectively. The filter sections are designed using the standard waveguides of the next frequency band to guarantee single-mode propagation, and taper sections are placed for the transition. Statistical analyses of the design parameters are performed to estimate the manufacturing tolerance. Microscope measurements are done and it is seen that machine tolerance on cavity lengths of about 3.5 microns causes a 2 GHz center frequency shift in Y-band. Measurements validate the analyses. The fabrication repeatability in the D-band is more consistent than in the Y-band. Indeed, two Y-band BPF units have a center frequency shift difference of 6 GHz while the the D-band BPF units have almost identical responses.