Giorgia Puleo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Giorgia Puleo has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Giuseppe Arrabito
University of Palermo Viale delle Scienze
3 shared publications Bruno Pignataro
Department of Physics and Chemistry ‐ Emilio Segrè University of Palermo Palermo Italy
2 shared publicationsFloriana Campanile
Department of Biomedical and Biotechnological Sciences, Section of Microbiology University of Catania Catania Italy
2 shared publications- Mariano Licciardi
Department of Biological, Chemical and Pharmaceutical Sciences and Technologies (STEBICEF), University of Palermo, via Archirafi 30, 90123 Palermo, Italy
2 shared publications Sebastiano Alberto Fortuna
Department of Biomedical and Biotechnological Sciences, Section of Microbiology University of Catania Catania Italy
2 shared publicationsValentina Catania
2 shared publications
Latest Publications
- Open Access
- 5 June 2026
- Published by Wiley in The Chemical Record
- Vol. 26 (9) , e70186
Printing to Fight Antimicrobial Resistance Through Nano/Microstructured Platforms
Antimicrobial resistance is one of the most pressing global public health threats, responsible for millions of deaths annually. To tackle this issue, additive manufacturing has been increasingly exploited to fabricate structured antimicrobial platforms with precise control over composition, geometry, and release kinetics. This review covers the most relevant approaches across different scales, from dip‐pen nanolithography and inkjet printing to 3D and 4D printing, emphasizing the role of nanoscale confinement, microenvironmental control, and interfacial chemistry as key design parameters. Polymeric matrices, metal and metal oxide nanostructures, and theranostic platforms are discussed in relation to their fabrication‐dependent properties, including material stability, ageing, and translational challenges. Finally, stimuli‐responsive architectures, phototherapeutic strategies, and artificial intelligence‐driven design are outlined as emerging tools toward next‐generation antimicrobial materials.
- 5 June 2026
- Published by Wiley in The Chemical Record
- Vol. 26 (9) , e70186
Open AccessPrinting to Fight Antimicrobial Resistance Through Nano/Microstructured Platforms
Antimicrobial resistance is one of the most pressing global public health threats, responsible for millions of deaths annually. To tackle this issue, additive manufacturing has been increasingly exploited to fabricate structured antimicrobial platforms with precise control over composition, geometry, and release kinetics. This review covers the most relevant approaches across different scales, from dip‐pen nanolithography and inkjet printing to 3D and 4D printing, emphasizing the role of nanoscale confinement, microenvironmental control, and interfacial chemistry as key design parameters. Polymeric matrices, metal and metal oxide nanostructures, and theranostic platforms are discussed in relation to their fabrication‐dependent properties, including material stability, ageing, and translational challenges. Finally, stimuli‐responsive architectures, phototherapeutic strategies, and artificial intelligence‐driven design are outlined as emerging tools toward next‐generation antimicrobial materials.
- Open Access
- 13 February 2026
- Published by Elsevier in Colloids and Surfaces A: Physicochemical and Engineering Aspects
- Vol. 738
Exploring ZnO microcrystals through experimental design: from solar photocatalysis to antibacterial activity
- 13 February 2026
- Published by Elsevier in Colloids and Surfaces A: Physicochemical and Engineering Aspects
- Vol. 738
Open AccessExploring ZnO microcrystals through experimental design: from solar photocatalysis to antibacterial activity
- Open Access
Functionalized Cellulose from Citrus Waste as a Sustainable Oil Adsorbent Material
Oil spills are a significant environmental issue for marine wildlife and coastal communities. Cellulose derived from citrus peel industrial waste is an interesting, economical, and eco-friendly advantageous material that was used for the first time with the aim of developing a low-cost and sustainable sorbent for water purification. Citrus peel cellulose was grafted with methyl acrylate to enhance hydrophobicity and favor the oil adsorption in aqueous media. Grafting copolymerization was performed in a simple manner, and the conditions were optimized in terms of monomer concentration, amount of catalyst, time, and temperature. The modified cellulose polymer was obtained in different grafting percentages, with a maximum of 93% grafting. Fourier transform infrared spectroscopy (FTIR), 1H NMR, scanning electron microscopy (SEM), and electrochemical impedance spectroscopy (EIS) analysis were used to confirm the graft copolymerization of poly(methyl acrylate) (PMA) onto the mercerized cellulose. Finally, the oil adsorption capacity of selected copolymers from freshwater, artificial seawater, and seawater samples was tested in a continuous-flow system. The results showed promising performance retaining diesel in seawater (4.01 g oil/g cellulose), demonstrating the use of agri-food waste as a natural sorbent in oil removal.
Open AccessFunctionalized Cellulose from Citrus Waste as a Sustainable Oil Adsorbent Material
Oil spills are a significant environmental issue for marine wildlife and coastal communities. Cellulose derived from citrus peel industrial waste is an interesting, economical, and eco-friendly advantageous material that was used for the first time with the aim of developing a low-cost and sustainable sorbent for water purification. Citrus peel cellulose was grafted with methyl acrylate to enhance hydrophobicity and favor the oil adsorption in aqueous media. Grafting copolymerization was performed in a simple manner, and the conditions were optimized in terms of monomer concentration, amount of catalyst, time, and temperature. The modified cellulose polymer was obtained in different grafting percentages, with a maximum of 93% grafting. Fourier transform infrared spectroscopy (FTIR), 1H NMR, scanning electron microscopy (SEM), and electrochemical impedance spectroscopy (EIS) analysis were used to confirm the graft copolymerization of poly(methyl acrylate) (PMA) onto the mercerized cellulose. Finally, the oil adsorption capacity of selected copolymers from freshwater, artificial seawater, and seawater samples was tested in a continuous-flow system. The results showed promising performance retaining diesel in seawater (4.01 g oil/g cellulose), demonstrating the use of agri-food waste as a natural sorbent in oil removal.
- Open Access
- 14 March 2025
- Published by Elsevier in Journal of Drug Delivery Science and Technology
- Vol. 107
Polybutylene succinate-based electrospun scaffolds improving skin permeation of the antibacterial ciprofloxacin
- 14 March 2025
- Published by Elsevier in Journal of Drug Delivery Science and Technology
- Vol. 107
Open AccessPolybutylene succinate-based electrospun scaffolds improving skin permeation of the antibacterial ciprofloxacin
- Open Access
- 20 December 2024
- Published by Elsevier in International Journal of Pharmaceutics
- Vol. 669, 125108
Redox/NIR dual-responsive glutathione extended polyurethane urea electrospun membranes for synergistic chemo-photothermal therapy
- 20 December 2024
- Published by Elsevier in International Journal of Pharmaceutics
- Vol. 669, 125108
Open AccessRedox/NIR dual-responsive glutathione extended polyurethane urea electrospun membranes for synergistic chemo-photothermal therapy
- Open Access
- 17 November 2023
- Published by Elsevier in Powder Technology
- Vol. 432
Electrosprayed Poly-butyl-succinate microparticles for sustained release of Ciprofloxacin as an antimicrobial delivery system
- 17 November 2023
- Published by Elsevier in Powder Technology
- Vol. 432
Open AccessElectrosprayed Poly-butyl-succinate microparticles for sustained release of Ciprofloxacin as an antimicrobial delivery system