Manish Bishwokarma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Manish Bishwokarma has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Ying Yang
University of Nevada, Reno
3 shared publications - Dani Or
Department of Civil and Environmental Engineering, University of Nevada, USA
2 shared publications - Yutong Cui
Department of Civil and Environmental Engineering, University of Nevada 1 , Reno, Nevada 89557
2 shared publications Cheng Zhang
Univ Nevada, Dept Mech Engn, Reno, NV 89557 USA
1 shared publication- Danyang Zhao
State Key Laboratory of High-Performance Precision Manufacturing, Dalian University of Technology, Dalian 116024, China
1 shared publication Erick Bandala
Univ Nevada, Dept Mech Engn, Reno, NV 89557 USA
1 shared publication
Latest Publications
- 1 November 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (11)
Size-dependent transport and adhesion of heat-activated resin droplets in geothermal fractures
The presence of rapid flow pathways through large, well-connected fractures reduces heat-exchange efficiency and the economic viability of enhanced geothermal systems (EGSs). However, when high permeability fractures form during fracking or seismic activity, only a few methods are available to mitigate their impact on the performance of EGSs. We recently proposed a method that employs thermally activated epoxy resin droplets that are transported with the flow to hot regions where the resin droplets foam and adhere to the fracture walls, thus selectively reducing the local permeability. A proof of concept was reported; however, the transport dynamics and statistical behavior of droplet adhesion were not fully characterized. Here, we report a hydrodynamic model for the transport and adhesion behavior of thermally activated resin droplets and laboratory experiments in simple fractures. We characterize the velocity of resin droplets in fractures considering the distribution of injected droplet size and the onset of thermal activation on volume expansion, adhesion, and curing. The resulting blockage of the fracture during laboratory experiments was in good agreement with the adhesion predicted without feedback. Initially, isolated large droplets with low velocity adhere near the transition to the hot region and alter the flow field, resulting in interactions with subsequent droplets. The overall pressure drop across the fracture gradually increases even after resin injection stops, demonstrating the contribution of foaming and curing after attachment to hydraulic blockage. The hydrodynamic model supported by observations provides a mechanistic basis for the prediction of resin droplet blockage and subsequent flow rerouting in large geothermal fractures.
- 1 November 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (11)
Size-dependent transport and adhesion of heat-activated resin droplets in geothermal fractures
The presence of rapid flow pathways through large, well-connected fractures reduces heat-exchange efficiency and the economic viability of enhanced geothermal systems (EGSs). However, when high permeability fractures form during fracking or seismic activity, only a few methods are available to mitigate their impact on the performance of EGSs. We recently proposed a method that employs thermally activated epoxy resin droplets that are transported with the flow to hot regions where the resin droplets foam and adhere to the fracture walls, thus selectively reducing the local permeability. A proof of concept was reported; however, the transport dynamics and statistical behavior of droplet adhesion were not fully characterized. Here, we report a hydrodynamic model for the transport and adhesion behavior of thermally activated resin droplets and laboratory experiments in simple fractures. We characterize the velocity of resin droplets in fractures considering the distribution of injected droplet size and the onset of thermal activation on volume expansion, adhesion, and curing. The resulting blockage of the fracture during laboratory experiments was in good agreement with the adhesion predicted without feedback. Initially, isolated large droplets with low velocity adhere near the transition to the hot region and alter the flow field, resulting in interactions with subsequent droplets. The overall pressure drop across the fracture gradually increases even after resin injection stops, demonstrating the contribution of foaming and curing after attachment to hydraulic blockage. The hydrodynamic model supported by observations provides a mechanistic basis for the prediction of resin droplet blockage and subsequent flow rerouting in large geothermal fractures.
- Open Access
- 15 May 2026
- Published by The International Society for Porous Media (InterPore) in InterPore Journal
- Vol. 3 (2) , IPJ150526-7
Heat-activated epoxy foam for permeability alteration in fractured geothermal fields: proof of concept
Geothermal energy plays a growing role in the transition to renewable and carbon free energy sources. A challenge for many geothermal operations is how to enhance water-rock heat exchange, either by creation of new fractures in a tight rock or by blocking short-circuiting large conduits. Here we report a novel approach for blocking large aperture (cm scale) fractures using heat-activated epoxy resin foam. The foam is injected as discrete inert resin droplets that are transported to regions of the geothermal field and activated upon reaching sufficiently high temperatures, where they undergo foaming and curing, thereby locally reducing permeability. In contrast to alternative methods for reducing rock permeability such as silicate gels or heat responsive polymer microbeads that target fractures of small apertures (< 0.1 mm), the epoxy foam can reduce permeability of fractures with large apertures (∼ 10 mm) while attaining mechanical strength and thermal stability. Results from laboratory aluminum-glass fracture models provide insights by visualizing the transport phase of resin droplets and their subsequent temperature-induced foaming and curing transformations with associated flow pathway blocking. Modeling results for transport and foaming in a simple fracture considering rheological properties and foaming (volume expansion) behavior are compared with measurements of permeability changes. Challenges associated with upscaling to fracture networks and large transport distances of resin droplets are discussed.
- 15 May 2026
- Published by The International Society for Porous Media (InterPore) in InterPore Journal
- Vol. 3 (2) , IPJ150526-7
Open AccessHeat-activated epoxy foam for permeability alteration in fractured geothermal fields: proof of concept
Geothermal energy plays a growing role in the transition to renewable and carbon free energy sources. A challenge for many geothermal operations is how to enhance water-rock heat exchange, either by creation of new fractures in a tight rock or by blocking short-circuiting large conduits. Here we report a novel approach for blocking large aperture (cm scale) fractures using heat-activated epoxy resin foam. The foam is injected as discrete inert resin droplets that are transported to regions of the geothermal field and activated upon reaching sufficiently high temperatures, where they undergo foaming and curing, thereby locally reducing permeability. In contrast to alternative methods for reducing rock permeability such as silicate gels or heat responsive polymer microbeads that target fractures of small apertures (< 0.1 mm), the epoxy foam can reduce permeability of fractures with large apertures (∼ 10 mm) while attaining mechanical strength and thermal stability. Results from laboratory aluminum-glass fracture models provide insights by visualizing the transport phase of resin droplets and their subsequent temperature-induced foaming and curing transformations with associated flow pathway blocking. Modeling results for transport and foaming in a simple fracture considering rheological properties and foaming (volume expansion) behavior are compared with measurements of permeability changes. Challenges associated with upscaling to fracture networks and large transport distances of resin droplets are discussed.
- 30 December 2024
- Published by IOP Publishing in Biofabrication
- Vol. 17 (1) , 015042
Embedded 3D printing of engineered lung cancer model for assisting fine-needle aspiration biopsy
Lung cancer is a serious global health issue that requires the development of patient-specific, lung cancer model for surgical planning to train interventionalists and improve the accuracy of biopsies. Although the emergence of three-dimensional (3D) printing provides a promising solution to create customized models with complicated architectures, current 3D printing methods cannot accurately duplicate anatomical-level lung constructs with tumor(s) which are applicable for hands-on training and procedure planning. To address this issue, an embedded printing strategy is proposed to create respiratory bronchioles, blood vessels, and tumors in a photocurable yield-stress matrix bath. After crosslinking, a patient-specific lung cancer analogous model is produced, which has tunable transparency and mechanical properties to mimic lung parenchyma. This engineered model not only enables the practical training of fine-needle aspiration biopsy but also provides the necessary information, such as coordinates of aspiration, wound depth, and interference with surrounding tissues, for procedure optimization.
- 30 December 2024
- Published by IOP Publishing in Biofabrication
- Vol. 17 (1) , 015042
Embedded 3D printing of engineered lung cancer model for assisting fine-needle aspiration biopsy
Lung cancer is a serious global health issue that requires the development of patient-specific, lung cancer model for surgical planning to train interventionalists and improve the accuracy of biopsies. Although the emergence of three-dimensional (3D) printing provides a promising solution to create customized models with complicated architectures, current 3D printing methods cannot accurately duplicate anatomical-level lung constructs with tumor(s) which are applicable for hands-on training and procedure planning. To address this issue, an embedded printing strategy is proposed to create respiratory bronchioles, blood vessels, and tumors in a photocurable yield-stress matrix bath. After crosslinking, a patient-specific lung cancer analogous model is produced, which has tunable transparency and mechanical properties to mimic lung parenchyma. This engineered model not only enables the practical training of fine-needle aspiration biopsy but also provides the necessary information, such as coordinates of aspiration, wound depth, and interference with surrounding tissues, for procedure optimization.