John B. Copp
Research Subjects
John B. Copp has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Andrew Shaw
Department of Experimental Oncology, Cross Cancer Institute, Edmonton, Alberta, Canada
1 shared publication B. Tole
Hydromantis Inc., Consulting Engineers, 1685 Main St. West, Suite 302, Hamilton, Ontario, L8S 1G5, Canada
1 shared publication- Benedek Gy. Plósz
Department of Chemical Engineering, University of Bath, Claverton Down, Bath BA2 7AY, UK; SWING - Department of Built Environment, Oslo Metropolitan University, St Olavs plass 0130, Oslo, Norway
1 shared publication - Borja Valverde-Pérez
Department of Environmental and Resource Engineering, Technical University of Denmark, Lyngby, Denmark
1 shared publication - Bruce R. Johnson
Jacobs, 9191 Jamaica St, Englewood, CO 80112, USA
1 shared publication - David Ikumi
Water Research Group, Department of Civil Engineering, University of Cape Town, Rondebosch 7700, South Africa
1 shared publication
Latest Publications
- Open Access
- 31 March 2022
- Published by IWA Publishing in Water Science & Technology
- Vol. 85 (10) , 2840-2853
The transition of WRRF models to digital twin applications
Digital Twins (DTs) are on the rise as innovative, powerful technologies to harness the power of digitalisation in the WRRF sector. The lack of consensus and understanding when it comes to the definition, perceived benefits and technological needs of DTs is hampering their widespread development and application. Transitioning from traditional WRRF modelling practice into DT applications raises a number of important questions: When is a model's predictive power acceptable for a DT? Which modelling frameworks are most suited for DT applications? Which data structures are needed to efficiently feed data to a DT? How do we keep the DT up to date and relevant? Who will be the main users of DTs and how to get them involved? How do DTs push the water sector to evolve? This paper provides an overview of the state-of-the-art, challenges, good practices, development needs and transformative capacity of DTs for WRRF applications.
- 31 March 2022
- Published by IWA Publishing in Water Science & Technology
- Vol. 85 (10) , 2840-2853
Open AccessThe transition of WRRF models to digital twin applications
Digital Twins (DTs) are on the rise as innovative, powerful technologies to harness the power of digitalisation in the WRRF sector. The lack of consensus and understanding when it comes to the definition, perceived benefits and technological needs of DTs is hampering their widespread development and application. Transitioning from traditional WRRF modelling practice into DT applications raises a number of important questions: When is a model's predictive power acceptable for a DT? Which modelling frameworks are most suited for DT applications? Which data structures are needed to efficiently feed data to a DT? How do we keep the DT up to date and relevant? Who will be the main users of DTs and how to get them involved? How do DTs push the water sector to evolve? This paper provides an overview of the state-of-the-art, challenges, good practices, development needs and transformative capacity of DTs for WRRF applications.
- 1 June 2013
- Published by IWA Publishing in Water Science & Technology
- Vol. 67 (11) , 2363-2373
Rethinking wastewater characterisation methods for activated sludge systems – a position paper
Increasingly stringent effluent limits and an expanding scope of model system boundaries beyond activated sludge has led to new modelling objectives and consequently to new and often more detailed modelling concepts. Nearly three decades after the publication of Activated Sludge Model No1 (ASM1), the authors believe it is time to re-evaluate wastewater characterisation procedures and targets. The present position paper gives a brief overview of state-of-the-art methods and discusses newly developed measurement techniques on a conceptual level. Potential future paths are presented including on-line instrumentation, promising measuring techniques, and mathematical solutions to fractionation problems. This is accompanied by a discussion on standardisation needs to increase modelling efficiency in our industry.
- 1 June 2013
- Published by IWA Publishing in Water Science & Technology
- Vol. 67 (11) , 2363-2373
Rethinking wastewater characterisation methods for activated sludge systems – a position paper
Increasingly stringent effluent limits and an expanding scope of model system boundaries beyond activated sludge has led to new modelling objectives and consequently to new and often more detailed modelling concepts. Nearly three decades after the publication of Activated Sludge Model No1 (ASM1), the authors believe it is time to re-evaluate wastewater characterisation procedures and targets. The present position paper gives a brief overview of state-of-the-art methods and discusses newly developed measurement techniques on a conceptual level. Potential future paths are presented including on-line instrumentation, promising measuring techniques, and mathematical solutions to fractionation problems. This is accompanied by a discussion on standardisation needs to increase modelling efficiency in our industry.
- Open Access
- 1 February 2009
- Published by IWA Publishing in Water Science & Technology
- Vol. 59 (4) , 695-704
Wastewater treatment modelling in practice: a collaborative discussion of the state of the art
Three consulting teams conducted independent modelling projects for three different wastewater treatment plants ranging in size from approximately 113,800 m3/d (30 mgd) to 530,000 m3/d (140 mgd), in different parts of the world (USA and Finland). The plants have different treatment objectives ranging from nitrification and partial denitrification (nitrate plus nitrite <8.7 mg/L) to enhanced nutrient removal (total nitrogen <3 mg/L, total phosphorus <0.3 mg/L). Commonly-used models were applied in the case studies, including ASM3 (using the GPS-X simulator), New General (using GPS-X), Dold (using BioWin), and a variation of the Dold model methanol degradation capabilities (NGmeth within GPS-X). The authors compare and contrast the modelling approaches taken, including calibration and validation approaches, sensitivity analyses, and the application of results to full-scale studies, designs and operations. Despite several differences between the approaches, there are many similarities which are discussed in light of the IWA draft uniform protocol for activated sludge modelling. The authors also discuss current modelling limitations and offer suggestions to improve the state of the art.
- 1 February 2009
- Published by IWA Publishing in Water Science & Technology
- Vol. 59 (4) , 695-704
Open AccessWastewater treatment modelling in practice: a collaborative discussion of the state of the art
Three consulting teams conducted independent modelling projects for three different wastewater treatment plants ranging in size from approximately 113,800 m3/d (30 mgd) to 530,000 m3/d (140 mgd), in different parts of the world (USA and Finland). The plants have different treatment objectives ranging from nitrification and partial denitrification (nitrate plus nitrite <8.7 mg/L) to enhanced nutrient removal (total nitrogen <3 mg/L, total phosphorus <0.3 mg/L). Commonly-used models were applied in the case studies, including ASM3 (using the GPS-X simulator), New General (using GPS-X), Dold (using BioWin), and a variation of the Dold model methanol degradation capabilities (NGmeth within GPS-X). The authors compare and contrast the modelling approaches taken, including calibration and validation approaches, sensitivity analyses, and the application of results to full-scale studies, designs and operations. Despite several differences between the approaches, there are many similarities which are discussed in light of the IWA draft uniform protocol for activated sludge modelling. The authors also discuss current modelling limitations and offer suggestions to improve the state of the art.
- 1 February 2006
- Published by IWA Publishing in Water Science & Technology
- Vol. 53 (4-5) , 375-382
Fault detection for control of wastewater treatment plants
Interest in real-time model-based control is increasing as more and more facilities are being asked to meet stricter effluent requirements while at the same time minimizing costs. It has been identified that biological process models and automated process control technologies are being used at wastewater treatments plants throughout the world and that great potential for optimising biotreatment may exist with the integration of these two technology areas. According to our experience, wastewater treatment plants are indeed looking for ways to successfully integrate their modelling knowledge into their process control structure; however, there are practical aspects of this integration that must be addressed if the benefits of this integration are to be realised. This paper discusses the practical aspects of monitoring, filtering and analysing real sensor data with an aim to produce a reliable real-time data stream that might be used within a model-based control structure. Several real case study examples are briefly discussed in this paper.
- 1 February 2006
- Published by IWA Publishing in Water Science & Technology
- Vol. 53 (4-5) , 375-382
Fault detection for control of wastewater treatment plants
Interest in real-time model-based control is increasing as more and more facilities are being asked to meet stricter effluent requirements while at the same time minimizing costs. It has been identified that biological process models and automated process control technologies are being used at wastewater treatments plants throughout the world and that great potential for optimising biotreatment may exist with the integration of these two technology areas. According to our experience, wastewater treatment plants are indeed looking for ways to successfully integrate their modelling knowledge into their process control structure; however, there are practical aspects of this integration that must be addressed if the benefits of this integration are to be realised. This paper discusses the practical aspects of monitoring, filtering and analysing real sensor data with an aim to produce a reliable real-time data stream that might be used within a model-based control structure. Several real case study examples are briefly discussed in this paper.