Samuel H. Hales
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Samuel H. Hales has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Cordelia Latham
Department of Mechanical Engineering, University of Utah, Salt Lake City, UT 84112, USA
1 shared publication - Derrick Wong
Department of Mechanical Engineering, University of Utah, Salt Lake City, UT 84112, USA
1 shared publication - Dwipak Prasad Sahu
Department of Physics, Ravenshaw University, Cuttack 753003, Odisha, India
1 shared publication - Isaac J. Cutler
Department of Mechanical Engineering, Brigham Young University, Provo, UT 84602, USA
1 shared publication - Jacob Redd
Department of Mechanical Engineering, Brigham Young University, Provo, UT 84602, USA
1 shared publication - Jared Anklam
Department of Mechanical Engineering, Rice University, Houston, TX 77005, USA
1 shared publication
Latest Publications
- Open Access
- 6 February 2026
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 12 (6) , eadz7415
Three-dimensional printing of nanomaterials-based electronics with a metamaterial-inspired near-field electromagnetic structure
Three-dimensional (3D) printing can create freeform architectures and electronics with unprecedented versatility. However, the full potential of electronic 3D printing has so far been limited by the inability to selectively anneal the printed materials, especially on temperature-sensitive substrates. Here, we achieve highly selective and rapid volumetric heating of 3D-printed nanomaterials and polymers in situ by focusing microwaves using a metamaterial-inspired near-field electromagnetic structure (Meta-NFS). In contrast to previous work, the Meta-NFS achieves the spatial resolution and power density needed to 3D print freeform microstructures where the electronic and mechanical properties can be locally programmed even within optically opaque materials. By broadening the material palettes compatible with 3D printing, near-field microwave 3D printing with Meta-NFS enables classes of electronics that are otherwise challenging to create.
- 6 February 2026
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 12 (6) , eadz7415
Open AccessThree-dimensional printing of nanomaterials-based electronics with a metamaterial-inspired near-field electromagnetic structure
Three-dimensional (3D) printing can create freeform architectures and electronics with unprecedented versatility. However, the full potential of electronic 3D printing has so far been limited by the inability to selectively anneal the printed materials, especially on temperature-sensitive substrates. Here, we achieve highly selective and rapid volumetric heating of 3D-printed nanomaterials and polymers in situ by focusing microwaves using a metamaterial-inspired near-field electromagnetic structure (Meta-NFS). In contrast to previous work, the Meta-NFS achieves the spatial resolution and power density needed to 3D print freeform microstructures where the electronic and mechanical properties can be locally programmed even within optically opaque materials. By broadening the material palettes compatible with 3D printing, near-field microwave 3D printing with Meta-NFS enables classes of electronics that are otherwise challenging to create.
- Open Access
An Inexpensive, 3D-Printable, Arduino- and Blu-Ray-Based Confocal Laser and Fluorescent Scanning Microscope
There is a growing field that is devoted to developing inexpensive microscopes and measurement devices by leveraging low-cost commercial parts that can be controlled using smartphones or embedded devices, such as Arduino and Raspbery Pi. Examples include the use of Blu-ray optical heads like the PHR-803T to perform cytometry, spinning disc microscopy, and lensless holographic microscopy. The modular or disposable nature of these devices means that they can also be used in contaminating and degrading environments, including radioactive environments, where replacement of device elements can be expensive. This paper presents the development and operation of a confocal microscope that uses the PHR-803T optical device in a Blu-ray reader for both imaging and detection of temperature variations with between 1.5 and 15 µm resolution. The benefits of using a PHR-803T confocal system include its relatively inexpensive design and the accessibility of the components that are used in its construction. The design of this scanning confocal thermal microscope (SCoT) was optimized based on cost, modularity, portability, spatial resolution, and ease of manufacturability using common tools (e.g., drill press, 3D printer). This paper demonstrated the ability to resolve microscale features such as synthetic spider silk and measure thermal waves in stainless steel using a system requiring <USD 1000 in material costs.
Open AccessAn Inexpensive, 3D-Printable, Arduino- and Blu-Ray-Based Confocal Laser and Fluorescent Scanning Microscope
There is a growing field that is devoted to developing inexpensive microscopes and measurement devices by leveraging low-cost commercial parts that can be controlled using smartphones or embedded devices, such as Arduino and Raspbery Pi. Examples include the use of Blu-ray optical heads like the PHR-803T to perform cytometry, spinning disc microscopy, and lensless holographic microscopy. The modular or disposable nature of these devices means that they can also be used in contaminating and degrading environments, including radioactive environments, where replacement of device elements can be expensive. This paper presents the development and operation of a confocal microscope that uses the PHR-803T optical device in a Blu-ray reader for both imaging and detection of temperature variations with between 1.5 and 15 µm resolution. The benefits of using a PHR-803T confocal system include its relatively inexpensive design and the accessibility of the components that are used in its construction. The design of this scanning confocal thermal microscope (SCoT) was optimized based on cost, modularity, portability, spatial resolution, and ease of manufacturability using common tools (e.g., drill press, 3D printer). This paper demonstrated the ability to resolve microscale features such as synthetic spider silk and measure thermal waves in stainless steel using a system requiring <USD 1000 in material costs.