TPTaras Pylypaka

Taras Pylypaka

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Taras Pylypaka has a total of 44 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Construction of a generalized mathematical model for particle transportation by straight helicoids in a vertical conveyor

    by Tetiana Volina, Serhii Pylypaka, Ivan Rogovskii, Iryna Hryshchenko, Nataliia Tarelnyk, Oleksandr Pavlenko, Svitlana Botvinovska, Artem Borodai, Serhii Andrukh, Taras Pylypaka

    This study investigates complex motion of a particle that simultaneously interacts with a vertical helicoid rotating around a vertical axis and a stationary limiting cylindrical casing. The helicoid can be closed (the rectilinear generating surfaces intersect the shaft at a right angle) or open (they are tangent to the shaft). The point of contact can be located on two symmetrical sides, which makes the helicoid variants surfaces that affect the particle transport differently. The task addressed relates to the fact that the geometric differences of helicoids are usually not taken into account. This leads to a significant simplification of the calculation models. A system of differential equations of particle motion was constructed and solved numerically. A condition for particle sticking after stabilization of the motion was found. It was shown that the same particle lift speed can be achieved by combinations of the angular velocity of rotation of the helicoid and the angle of lift of its edge. In terms of the particle lifting speed, the closed helicoid occupies an intermediate position compared to the two open variants. Values of particle movement speeds after stabilization of the movement under different initial conditions were found. Theoretical studies were conducted on a conveyor limited by an inner shaft with a radius of 0.03 m and an outer limiting cylinder with a radius of 0.1 m. It is shown that at an angular speed of rotation of a straight helicoid of 15 s–1, friction coefficients of 0.3 on both surfaces, the limiting value of the helicoid edge lifting angle at which the particle hangs is 17.8°. The generalized mathematical model built makes it possible to describe the motion modes for different types of helicoids. The scope of application of the results is mechanical engineering in the design and optimization of working elements of vertical screw conveyors for transporting bulk materials

  • Open Access

    Devising a technique for constructing helical architectural objects from curvilinear strips of constant width

    by Andrii Nesvidomin, Serhii Pylypaka, Mykhailo Kalenyk, Ivan Rogovskii, Dmytro Borodai, Dmytro Spirintsev, Vyacheslav Hropost, Taras Pylypaka, Yuriy Semirnenko, Irina Zakharova

    This study investigates the process of constructing helical surfaces with a cross-section in the form of an isosceles triangle or a rhombus. The task addressed relates to the impossibility of obtaining an accurate sweep of non-sweep helical surfaces. Obtaining such surfaces from approximate sweeps leads to shear and tensile deformations of the sheet material, to the formation of kinks and a large number of joining seams. This requires devising a technique for approximating a non-sweep helical tubular surface with strips of tangentially spread surfaces. This approach allows for the manufacture of helical surfaces from strips of sheet material by simply bending them into the desired shape. This work’s results make it possible to construct such composite surfaces according to the specified design parameters, which are the helix – the axis of the surface – and the shape of the cross-section. Individual strips are spread surfaces but are not surfaces of the same slope of the generatrixes. In this regard, finding their sweeps, that is, the contours of flat workpieces, requires numerical integration methods. A feature of the devised approach is the possibility of approximating a non-sweep helical surface by strips of sweeps. In the work, a composite helical surface was calculated and constructed along its given axis – a helical line with parameters a = 10, b = 5. The cross-section of the surface is a rhombus described around a circle of radius r = 1 with acute angles at the vertex 2φ = 40°. The scope of practical application of the results is architectural design and construction in terms of forming load-bearing or decorative helical elements. The condition for practical implementation is the transfer of the developed algorithms to CAD/CAM systems for automating the cutting of sheet metal with subsequent manufacturing of parts by bending

  • Open Access

    Devising a technique for constructing tubular surfaces referred to a coordinate grid of lines of curvature

    by Andrii Nesvidomin, Serhii Pylypaka, Tetiana Volina, Victor Nesvidomin, Oleksandr Solarov, Taras Voloshko, Taras Pylypaka, Lidiia Savchenko, Oleksandr Savchenko, Irina Zakharova

    This study considers the construction of tubular surfaces with a spatial axis of slope, referred to a coordinate grid of curvature lines. Such surfaces have a number of mathematical advantages compared to surfaces described by arbitrary coordinate grids. In differential geometry, this has a theoretical justification and applied value. This follows from the special role of curvature lines as geometrically privileged directions on a surface with minimal and maximal curvatures. To parameterize a tubular surface in this way, it is necessary that the length of its axis be described by analytical dependences in a finite form. Typically, the length of spatial curves is determined by numerical integration. There is a known group of plane curves that are described by parametric equations as a function of the arc length and for which such a problem does not exist. This work proposes taking such curves as a horizontal projection of a spatial curve. The spatial curve should be constructed as a slope curve with a constant elevation angle relative to the horizontal plane. Then the spatial curve, the equations of which include the elevation angle, will be described as a function of the arc length. Its use as the axis of the tubular surface makes it possible to attribute the latter to the families of coordinate lines of curvature. In this paper, the horizontal projection of the axis of the tubular surface is a logarithmic spiral. Parametric equations of the tubular surface in analytical form have been derived. A surface with the elevation angle of the axis β = 10° and the radius of the generating circle ρ = 15 linear units was constructed. The orthogonality of the resulting coordinate grid has been proven through the analysis of the coefficients of the first quadratic form (F = 0), which confirms the assignment of the surface to the lines of curvature. This makes it possible to improve the accuracy of calculating the stress-strain state of shells in mechanical engineering and aerospace engineering at simultaneous minimization of computational costs

  • Open Access

    A technique for approximating a tubular helical surface with strips of toruses

    by Andrii Nesvidomin, Serhii Pylypaka, Victor Nesvidomin, Vitaliy Babka, Olga Shoman, Oleksandr Savoiskyi, Taras Pylypaka, Mykola Lokhonia, Svetlana Semirnenko, Yana Borodai

    This study’s object is the approximation of a non-swept helical tubular surface by strips of sweeping surfaces (toruses) and the construction of sweeps of these strips. Approximating non-swept tubular surfaces by sections of sweep ones is a common practice in the design of various types of pipelines. A clear example of such an approximation is a sports ball whose outer shell consists of a certain number of separate elements. These elements must fit most tightly to the non-swept surface along its certain lines. Such lines are the lines of curvature. The task is to find these lines on the surface in order to subsequently analytically describe the torus strip, which is tangent to the non-swept surface along this line. As is known, there are two families of mutually perpendicular lines of curvature on surfaces. This paper considers a family of curvature lines that has advantages over another one in terms of approximation. This explains the results reported here. Their special feature is that in order to find the desired family of curvature lines, it is necessary to solve a differential equation. The solution to this equation was borrowed from a scientific article and used for further calculations. The results were visualized in the form of an approximated tubular surface with four and six strips. The sweeps of these strips were constructed for a tubular surface, in which the center line is a helical line r = 1. All dimensions are given in linear units. Instead of a circle generatrix, it is given by the radius of the cylinder a = 2, which hosts it, and the helical parameter b = 1.5 (step H = 9.4). The radius of the circle generatrix of the tubular surface of the original tubular surface in the approximated surface in the given examples is a polygon (square or equilateral hexagon).

  • Open Access

    Designing non-circular wheels using a fourth-degree polynomial

    by Tetiana Kresan, Serhii Pylypaka, Tetiana Volina, Vitaliy Babka, Svitlana Botvinovska, Alexander Sarzhanov, Taras Pylypaka, Artem Borodai, Dmytro Borodai, Yulia Sirenko

    This study’s object is the process of designing closed non-circular wheels with a given center-to-center distance with external rolling, provided that it occurs without mutual slip. Non-circular wheels serve as centroids in the design of cylindrical gear transmissions with a variable gear ratio. The gear ratio is characterized by the gear function. If the gear ratio is constant, then the centroids are circles. The gear ratio in this case is the ratio of the radii of these circles. Non-circular wheels can be designed according to a given gear function, which is determined by the kinematics of the mechanism’s links’ actuators. In this case, non-circular wheels can be non-closed. The study addresses another task related to designing non-circular wheels provided that they are closed. Various approaches can be used to this end. The current paper considers the use of a fourth-degree polynomial. In non-circular wheels, the radii, which are understood as the distances from the centers of rotation to the point of contact, are variable. The necessary conditions for constructing non-circular wheels are the constant value of the sum of these radii during the rotation of non-circular wheels, as well as the equality of the paths traveled, that is, the equality of the arcs that non-circular wheels pass during rotation. Pairs of wheels can have the same or different numbers of protrusions and depressions. This is explained by the use of a fourth-degree polynomial whose plot has an axis of symmetry. Accordingly, non-circular wheels or their protrusions also have an axis of symmetry. As an example, the construction of a leading centroid with one protrusion and one depression is given, for which the maximum and minimum distances from the center are 10 and 6.1 linear units, respectively. For this centroid, a trailing centroid has been constructed, and the center-to-center distance has been found, which is 16.79 linear units

  • Open Access

    Mathematical descripton of winding helicoid section construction based on the predefined structural parameters

    by Andrii Nesvidomin, Serhii Pylypaka, Tetiana Volina, Zinovii Ruzhilo, Olena Kozlova, Ivan Shuliak, Taras Pylypaka, Yaroslav Kremets, Olena Nalobina, Alla Rebrii

    The object of this study is a helical sweeping surface or a helicoid torso and the process of its design according to predefined structural parameters. Helical surfaces are widely used in engineering practice. They have become widespread in devices for transporting various materials, as well as in agricultural machinery. The problem is that when they are manufactured, the technique of their formation from the point of view of analytical description is not always taken into account. Helical surfaces can be linear and nonlinear. Linear surfaces, or helicoids, are formed by the helical motion of a straight-line generatrix around an axis, and the generatrix can intersect it or be coincident. If the straight-line generatrix intersects the axis at a right angle, then the helicoid will be a helical conoid, which is very common in technology under the name of a screw. Certain conditions are imposed on the helical motion of the straight-line generatrix of a helicoid torso. Its main advantage among other helicoids is the possibility of constructing an exact sweep. All other helicoids cannot be swept. For their manufacture, an approximate sweep is found, which is deformed into the desired shape. At the same time, the energy intensity of the process of deformation of this sweep into the finished product increases due to overcoming significant plastic deformations. As a result of this research, dependences were established that make it possible to construct a set of helicoid torsos that pass through the predefined helical line. The results are based on the differential characteristics of the surface. These are their distinctive features from known results, according to which only one helicoid torso corresponds to the predefined helical line. This paper shows the practical application of the helicoid torso as a supporting turn of the narrowing screw of a forage harvester with a radius of R=0.25 m of the outer edge and r=0.125 m of the inner one

  • Open Access

    BENDING OF THE SURFACES OF THE BINORMALS OF THE SLOPE LINES

    by Tetiana Kresan, Serhiy Pylypaka, Taras Pylypaka, Yaroslav Kremets, Iryna Hryshchenko, Сергій Пилипака, Тарас Пилипака, Ярослав Кремець, Ірина Грищенко

    The bending of the surfaces of the binormals by deformation of the directing curve, which is the slope line, is considered. Such deformation changes the curvature of the curve, but it remains a slope line. The rectilinear generators of the surfaces at deformation of the curve coincide with the unit binormal of the accompanying trihedral at all its points. Parametric equations of continuous bending of these surfaces have been made by changing the angle of inclination of the directional slope line. The initial slope curve is given by the angle of its rise and the conformity of change of curvature as a function of arc length. The partial case where the curvature of the initial curve is constant is considered. In this case, it is shown that helicoids, including the screw conoid, are the set of surface bends. Specific examples are considered. According to the obtained equations, the surfaces that are the bending of the initial are constructed. The doctrine of bending is an important part of the differential geometry of surfaces. The most studied in theoretical terms is the bending of the developable surfaces, because the particular case of bending such surfaces on the plane, that is, obtaining an involute, is applied. It is a well-known theorem on the possibility of bending screw surfaces into the surfaces of revolution. A classic example is the bending of a screw conoid into a catenoid. Screw lines of a surface at its bending gradually deform, their step decreases, until they turn into the parallels of a surface of revolution. Nondevelopable ruled surfaces can also be bent like developable ones, that is, deform the directing curve in such a way that rectilinear generators remain straight. This article is devoted to this bending of ruled non developable surfaces, where the slope line is a directing curve of the surface. Bending of linear unbranched surfaces can be carried out in the same way as unfolded, that is, with the preservation of rectilinear twists. A partial case of such bending is the bending of the surface of the binormals of the spatial curve guide. When the surface is bent, the guide curve is deformed so that its twist as a function of the arc length remains unchanged. Using the example of slope curves, which are directional curves of the surface of binormals, generalized parametric equations of bending such surfaces by changing the angle of their rise are obtained. When this angle increases to a limit value of 90°, the surface is transformed so that the slope curve turns into a straight line. The result of the bending of the surface of the binormals of the helical line is the helicoids and the helical conoid with a maximum lifting angle of 90 °.

  • Open Access

    AGRICULTURAL TOOLS FOR SURFACE SOIL CULTIVATION

    by Andrii Nesvidomin, Taras Pylypaka, Victor Nesvidomin, Віталій Бабка, Iryna Hryshchenko, Андрій Несвідомін, Тарас Пилипака, Віктор Несвідомін, Ірина Грищенко

    The object of the study is the process of finding a rational form of the tillage working organ of the drum type for reducing resistance when it is deepened into the soil. The working bodies of agricultural implements have different shapes: spring teeth, knives, cutters, chisels, paws, disks. They all interact with the soil environment, and can be active or passive. However, both in the first and in the second case, the resistance to their movement should be minimal. The article considers the shape of a curved tooth, which is fixedly fixed between two cylindrical discs that form a section. Several sections fixed on the shaft can form a drum. Such a tool can work like a side roller or a needle harrow, when they roll, the curved tooth is forcibly immersed in the soil with its subsequent loosening. It is proposed such a curvilinear shape of the tooth, which would work like a shovel: at the first stage of immersion in the soil, it glided as much as possible along it and deformed it minimally, and at the second stage it weighed it and turned it over. Such a process of deformation of the soil should reduce the resistance to its cultivation at the first stage, which determines the relevance of the research. The purpose of the work is to establish an analytical description of the shape of a curved tooth or blade, which, when immersed in soil, would slide as much as possible along themselves, thereby reducing the resistance to immersion. To do this, the work of the tooth of a rectilinear shape was analyzed, followed by its transformation into a curvilinear one according to the task. This curve of the tooth profile turned out to be the involute of the circle, which is known for its other technical application, such as the profile of the tooth in cylindrical gears. The trajectory of the point of attachment of the tooth to the discs is a cycloid, and its end is an elongated cycloid. Part of loop of elongated cycloid in soil medium forms area of treated soil. For any tooth shape, including straight, its end describes an elongated cycloid, but for a tooth in the form of an involute circle there is a feature. It consists in the fact that at the moment of contact of the tooth with the field surface, the vector of absolute speed is directed perpendicular to it. As the discs roll, the tooth sinks into the soil, and the point of entry into it remains unchanged, and the tooth itself slides almost along itself, especially in the upper layers of the soil. After diving to the maximum depth, he begins to weigh the soil on the surface or loosen it. The article establishes analytical dependencies, provides graphic illustrations on a scale that gives an idea of the work of the working body and the profile of the treated soil. This result makes it possible to make the necessary calculations, which gives the work practical value.

  • Open Access

    Determining the deformation of an absolutely elastic axis of curved rods under bending

    by Serhii Pylypaka, Victor Nesvidomin, Tetiana Volina, Iryna Hryshchenko, Taras Pylypaka, Yaroslav Kremets, Serhii Andrukh, Oleksandr Savoiskyi, Larysa Korzh-Usenko, Yuriy Semirnenko

    The object of this study is the deformation of an elastic axis with a large deflection of a cantilever clamped absolutely elastic rod under the action of an applied concentrated force. The rod in the free state can have a rectilinear or curved elastic axis. This fact implies a difference in the analytical description of the bending process. However, there is a factor by which some similarity can be found between the bending of rectilinear and curved rods. This factor is the curvature of the elastic axis of the rod in a free state. According to this feature, they can be divided into rods of constant and variable curvature of the elastic axis. The former include rectilinear rods and those that in the free state have the shape of an arc of a circle, and the latter – rods with a variable curvature of the elastic axis. There is a difference between the bending of these groups of rods: in the first case, the deformation of the elastic axis of the rod during its bending will be the same regardless of which end will be cantilever pinched. A distinctive feature of the current research is that the bending of rods with variable curvature of the elastic axis was carried out by alternate pinching of their opposite ends. Moreover, the rods of constant and variable curvature were of the same length s=0.314 m, the same cross-section of 0.005×0.02 m. That has made it possible to visually show the difference between the shape of the elastic axis of the bent rod under the action of the same force when the pinch end is changed. When attached to the rods of the working bodies of agricultural machines, pulsating dynamic loads are smoothed out due to their elasticity. It is important for practice to be able to calculate the value of their deviation, which should be within the given limits. The results are explained by the fact that in the analytical description of the shape of the elastic axis of a curved rod, a technique was proposed in which the length of the axis can start counting both from one end and from the opposite end