Valeriya Kostyukova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Valeriya Kostyukova has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
A. Pilipchuk
School of Physics and Engineering, ITMO University, St. Petersburg, Russia
1 shared publication- Altay Zhakatayev
Mechanical and Aerospace Engineering Department, Nazarbayev University, Astana, Kazakhstan
1 shared publication - Bakhtiyar Orazbayev
Physics Department, Nazarbayev University, Astana, Kazakhstan
1 shared publication Daryn Kenzhebek
Robotics Department, School of Engineering and Digital Sciences, Nazarbayev University, Astana, Kazakhstan
1 shared publication- Dmitry Shestakov
School of Physics and Engineering, ITMO University, St. Petersburg, Russia
1 shared publication E. Afanaseva
School of Physics and Engineering, ITMO University, St. Petersburg, Russia
1 shared publication
Latest Publications
- 1 December 2025
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 89 (S4) , S519-S522
Fabrication of Copper Electrodes by Direct Laser Metallization for Flexible Electronics
We presented a novel, maskless approach for fabricating copper electrodes on flexible polyimide substrates using direct laser metallization (DLM) from deep eutectic solvents (DES). The DLM process utilizes localized thermochemical reactions driven by a picosecond pulsed laser to convert DES precursors into conductive copper structures with precise patterning. Key parameters such as laser power density, scanning speed, and DES layer thickness were optimized to achieve uniform copper lines with excellent electrical conductivity and mechanical flexibility. The fabricated electrodes demonstrated remarkable stability under bending tests, showing less than 5% variation in resistance, which confirms their suitability for flexible pressure and strain sensor applications in wearable electronics and human–machine interfaces. This is the first demonstration of copper structures produced on polyimide via DES-based DLM with proven functional performance, highlighting its potential as a scalable, cost-effective method for next-generation flexible electronic device manufacturing.
- 1 December 2025
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 89 (S4) , S519-S522
Fabrication of Copper Electrodes by Direct Laser Metallization for Flexible Electronics
We presented a novel, maskless approach for fabricating copper electrodes on flexible polyimide substrates using direct laser metallization (DLM) from deep eutectic solvents (DES). The DLM process utilizes localized thermochemical reactions driven by a picosecond pulsed laser to convert DES precursors into conductive copper structures with precise patterning. Key parameters such as laser power density, scanning speed, and DES layer thickness were optimized to achieve uniform copper lines with excellent electrical conductivity and mechanical flexibility. The fabricated electrodes demonstrated remarkable stability under bending tests, showing less than 5% variation in resistance, which confirms their suitability for flexible pressure and strain sensor applications in wearable electronics and human–machine interfaces. This is the first demonstration of copper structures produced on polyimide via DES-based DLM with proven functional performance, highlighting its potential as a scalable, cost-effective method for next-generation flexible electronic device manufacturing.
- 12 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (1) , 577-586
Honeycomb-Inspired Metamaterial for Tactile Sensors With Variable Stiffness
The material’s stiffness plays a crucial role in tactile sensors and stiffness controllers of robot joints, facilitating safe and effective robot-environment interactions. Conventional controllers or sensors require a priori information about stiffness modulation to efficiently control environmental collisions and reduce their detrimental effects. Therefore, such inflexibility of real-time stiffness variation may cause instability if the dynamic mechanical system (a mass-spring-damper) changes during execution. In this paper, we tackle the problem using a honeycomb metamaterial with a tunable stiffness to design a tactile sensor capable of detecting physical contact with low and high-impact forces. We experimentally demonstrate that dynamic modification of the honeycomb structure reduces the maximum impact force by ≈ 30%, mitigating the rapid collision with the environment during contact detection. The results show that the honeycomb attachment allows for a more precise and controlled impact with varying degrees of energy and momentum transfer. The honeycomb attachment can be a valuable tool for grasping, explosive motion generation, and tactile sensing, requiring low-or-high-impact and controllable contact. Our study highlights the potential of using negative stiffness honeycomb structures to improve the functionality of tactile sensors.
- 12 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (1) , 577-586
Honeycomb-Inspired Metamaterial for Tactile Sensors With Variable Stiffness
The material’s stiffness plays a crucial role in tactile sensors and stiffness controllers of robot joints, facilitating safe and effective robot-environment interactions. Conventional controllers or sensors require a priori information about stiffness modulation to efficiently control environmental collisions and reduce their detrimental effects. Therefore, such inflexibility of real-time stiffness variation may cause instability if the dynamic mechanical system (a mass-spring-damper) changes during execution. In this paper, we tackle the problem using a honeycomb metamaterial with a tunable stiffness to design a tactile sensor capable of detecting physical contact with low and high-impact forces. We experimentally demonstrate that dynamic modification of the honeycomb structure reduces the maximum impact force by ≈ 30%, mitigating the rapid collision with the environment during contact detection. The results show that the honeycomb attachment allows for a more precise and controlled impact with varying degrees of energy and momentum transfer. The honeycomb attachment can be a valuable tool for grasping, explosive motion generation, and tactile sensing, requiring low-or-high-impact and controllable contact. Our study highlights the potential of using negative stiffness honeycomb structures to improve the functionality of tactile sensors.