Khalid F. Alqosaibi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Khalid F. Alqosaibi has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
Essam Al-Bahkali
1 shared publication- Hussam H. Noor
Department of Mechanical Engineering, College of Engineering, Taibah University, Medina 42353, Saudi Arabia
1 shared publication - Magdy Mostafa El Rayes
Department of Mechanical Engineering, College of Engineering, King Saud University, P.O. Box 800, Riyadh 12372, Saudi Arabia
1 shared publication - Shahid Parvez
Mechanical Engineering Department, King Saud University, Riyadh 12372, Saudi Arabia
1 shared publication
Latest Publications
- 17 September 2025
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 32 (2) , 219-231
Investigating the Electrical, Thermal, and Mechanical Properties of 3D Printed PLA /Talc/Graphene Composite Using Taguchi Method and Gray Relational Grade Analysis
This study investigates the electrical, thermal, and mechanical characteristics of Polylactic acid/Talc/Graphene (PLA/Talc/GPN) composites produced using the Fused Filament Fabrication (FFF) process. The process parameters, including talc content, GPN content, print speed, and nozzle temperature, are optimized using the Taguchi method and gray relational grade analysis. Subsequent material characterization is conducted through Scanning Electron Microscopy (SEM), Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), and four‐probe electrical tests. Results indicate that incorporating talc and graphene improved the composite's thermal stability. Furthermore, its electrical conductivity was greatest with a specific filler composition of 5 wt% talc and 1 wt% GPN. The findings from the Taguchi analysis revealed that the nozzle temperature and GPN content were the most significant parameters affecting elastic modulus and flexural strength. Subsequently, gray relational grade analysis determined the specific combination of parameters that optimized these properties: a GPN content of 1 wt%, a print speed of 30 mm/s, a talc content of 5 wt%, and a nozzle temperature of 215°C.
- 17 September 2025
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 32 (2) , 219-231
Investigating the Electrical, Thermal, and Mechanical Properties of 3D Printed PLA /Talc/Graphene Composite Using Taguchi Method and Gray Relational Grade Analysis
This study investigates the electrical, thermal, and mechanical characteristics of Polylactic acid/Talc/Graphene (PLA/Talc/GPN) composites produced using the Fused Filament Fabrication (FFF) process. The process parameters, including talc content, GPN content, print speed, and nozzle temperature, are optimized using the Taguchi method and gray relational grade analysis. Subsequent material characterization is conducted through Scanning Electron Microscopy (SEM), Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), and four‐probe electrical tests. Results indicate that incorporating talc and graphene improved the composite's thermal stability. Furthermore, its electrical conductivity was greatest with a specific filler composition of 5 wt% talc and 1 wt% GPN. The findings from the Taguchi analysis revealed that the nozzle temperature and GPN content were the most significant parameters affecting elastic modulus and flexural strength. Subsequently, gray relational grade analysis determined the specific combination of parameters that optimized these properties: a GPN content of 1 wt%, a print speed of 30 mm/s, a talc content of 5 wt%, and a nozzle temperature of 215°C.
- Open Access
- 1 January 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (1)
Numerical investigation of the influence of pulse frequency on the weld pool size in pulsed current TIG welding
This study simulates the pulsed current tungsten inert gas (TIG) welding process to investigate the transient development of the weld pool in a 4 mm thick aluminum sheet, focusing on the effects of pulse frequency on the weld pool size. Two pulsed currents, 230 and 180 A, with a 30% background current, were examined. The 230 A current achieved full, while the 180 A resulted in partial penetration. Five pulse frequencies (1, 4, 10, 20, and 50 Hz) were analyzed. A numerical model was developed to compute heat and current fluxes on the workpiece surface. The arc profile shifted from a bell shape in high-frequency cycles to a conical shape in low-frequency cycles. The heat and current fluxes served as inputs to another model that simulated weld pool behavior for both direct and pulsed current TIG welding. The results showed that weld pool size decreased in pulsed current TIG welding. At 230 A, full penetration changed to partial penetration under pulsed current. At 1 Hz, sufficient time was available for solidification during the low-cycle period, but at 50 Hz, the weld pool remained liquid. As pulse frequency increased from 1 to 50 Hz, the weld pool depth decreased significantly, with a reduction from 2.4 to 0.9 mm at 230 A and from 1.1 to 0.34 mm at 180 A. Convection in the weld pool was influenced by temperature and was strongest at higher temperatures. The decrease in weld pool size was most pronounced between 1 and 10 Hz, stabilizing between 20 and 50 Hz. Validation against experimental macrographs demonstrated good agreement with the simulations.
- 1 January 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (1)
Open AccessNumerical investigation of the influence of pulse frequency on the weld pool size in pulsed current TIG welding
This study simulates the pulsed current tungsten inert gas (TIG) welding process to investigate the transient development of the weld pool in a 4 mm thick aluminum sheet, focusing on the effects of pulse frequency on the weld pool size. Two pulsed currents, 230 and 180 A, with a 30% background current, were examined. The 230 A current achieved full, while the 180 A resulted in partial penetration. Five pulse frequencies (1, 4, 10, 20, and 50 Hz) were analyzed. A numerical model was developed to compute heat and current fluxes on the workpiece surface. The arc profile shifted from a bell shape in high-frequency cycles to a conical shape in low-frequency cycles. The heat and current fluxes served as inputs to another model that simulated weld pool behavior for both direct and pulsed current TIG welding. The results showed that weld pool size decreased in pulsed current TIG welding. At 230 A, full penetration changed to partial penetration under pulsed current. At 1 Hz, sufficient time was available for solidification during the low-cycle period, but at 50 Hz, the weld pool remained liquid. As pulse frequency increased from 1 to 50 Hz, the weld pool depth decreased significantly, with a reduction from 2.4 to 0.9 mm at 230 A and from 1.1 to 0.34 mm at 180 A. Convection in the weld pool was influenced by temperature and was strongest at higher temperatures. The decrease in weld pool size was most pronounced between 1 and 10 Hz, stabilizing between 20 and 50 Hz. Validation against experimental macrographs demonstrated good agreement with the simulations.