Xiaowei Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiaowei Li has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Yongquan Hu
3 shared publications- Yu Yang
State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University , Chengdu 610500
3 shared publications - Yufeng Wang
State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University , Chengdu 610500
3 shared publications - Jinzhou Zhao
State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University , Chengdu 610500
2 shared publications Qiang Wang
2 shared publications- Qiang Wang
State Key Laboratory of Oil-Gas Reservoir Geology & Exploitation, Southwest Petroleum University, Chengdu 610500, China
2 shared publications
Latest Publications
- 9 June 2026
- Published by Elsevier in Advanced Powder Technology
- Vol. 37 (8)
Transport law of proppant at engineering scale in the coupling of wellbore and multi-cluster hydraulic fractures
- 9 June 2026
- Published by Elsevier in Advanced Powder Technology
- Vol. 37 (8)
Transport law of proppant at engineering scale in the coupling of wellbore and multi-cluster hydraulic fractures
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Research on the propagation laws and influencing factors of hydraulic fractures in deep shale reservoirs based on the three-dimensional discrete lattice method
Unconventional shale gas reservoirs are an important part of oil and gas exploration and development. Generally, large-scale hydraulic fracturing is required to form a large number of complex fracture networks in the reservoir, so as to connect the reservoir volume and enhance reservoir permeability. However, during fracture initiation and propagation, unclear propagation patterns and controlling factors often cause issues such as perforation cluster failure to initiate or propagate effectively, hydraulic fracture merging, and unexpected propagation under natural fracture influence, making it difficult to form an effective complex network. To address these issues, we establish a three-dimensional fracture propagation model for deep shale gas horizontal wells using the discrete lattice method based on geological parameters from the deep shale gas block in southern Sichuan. Numerical simulations are conducted to investigate the effects of injection rate, cluster spacing, horizontal stress difference, and natural fracture approach angle on fracture propagation behavior. The results show that increasing the injection rate and cluster spacing can increase the number of initiated perforation clusters to a certain extent, thereby enhancing the number of hydraulic fractures and improving complexity. When the cluster spacing is 6 and 10 m, increasing the injection rate from 0.05 to 0.30 m3/s leads to an increase in over 40% of the number of effectively initiated clusters. When the injection rates are 0.15 and 0.20 m3/s, increasing the cluster spacing from 6 to 10 m results in an increase in over 20% in the number of effectively initiated clusters. However, when the cluster spacing is small, stress interference still prevents some central clusters from initiating and propagating properly even with higher injection rates, resulting in significantly smaller fracture volumes compared to others. Under low horizontal stress difference 8 MPa, fractures are prone to twist and form non-straight fractures and merge after initiation, affecting the fracture propagation distance. After increasing the horizontal stress difference to 14 MPa, fractures propagate to form more regular and straight hydraulic fractures, and the fractures can extend further. As the approach angle of the natural fractures increases, the propagation pressure of hydraulic fractures under the action of natural fractures gradually increases, and the hydraulic fractures transition from being captured by natural fractures to crossing them and eventually being arrested. Therefore, by increasing the injection rate and cluster spacing under higher horizontal stress differences, while promoting intersection with a small approach angle natural fracture, can enhance fracture network complexity and facilitate efficient hydraulic fracturing in deep shale gas reservoirs.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Research on the propagation laws and influencing factors of hydraulic fractures in deep shale reservoirs based on the three-dimensional discrete lattice method
Unconventional shale gas reservoirs are an important part of oil and gas exploration and development. Generally, large-scale hydraulic fracturing is required to form a large number of complex fracture networks in the reservoir, so as to connect the reservoir volume and enhance reservoir permeability. However, during fracture initiation and propagation, unclear propagation patterns and controlling factors often cause issues such as perforation cluster failure to initiate or propagate effectively, hydraulic fracture merging, and unexpected propagation under natural fracture influence, making it difficult to form an effective complex network. To address these issues, we establish a three-dimensional fracture propagation model for deep shale gas horizontal wells using the discrete lattice method based on geological parameters from the deep shale gas block in southern Sichuan. Numerical simulations are conducted to investigate the effects of injection rate, cluster spacing, horizontal stress difference, and natural fracture approach angle on fracture propagation behavior. The results show that increasing the injection rate and cluster spacing can increase the number of initiated perforation clusters to a certain extent, thereby enhancing the number of hydraulic fractures and improving complexity. When the cluster spacing is 6 and 10 m, increasing the injection rate from 0.05 to 0.30 m3/s leads to an increase in over 40% of the number of effectively initiated clusters. When the injection rates are 0.15 and 0.20 m3/s, increasing the cluster spacing from 6 to 10 m results in an increase in over 20% in the number of effectively initiated clusters. However, when the cluster spacing is small, stress interference still prevents some central clusters from initiating and propagating properly even with higher injection rates, resulting in significantly smaller fracture volumes compared to others. Under low horizontal stress difference 8 MPa, fractures are prone to twist and form non-straight fractures and merge after initiation, affecting the fracture propagation distance. After increasing the horizontal stress difference to 14 MPa, fractures propagate to form more regular and straight hydraulic fractures, and the fractures can extend further. As the approach angle of the natural fractures increases, the propagation pressure of hydraulic fractures under the action of natural fractures gradually increases, and the hydraulic fractures transition from being captured by natural fractures to crossing them and eventually being arrested. Therefore, by increasing the injection rate and cluster spacing under higher horizontal stress differences, while promoting intersection with a small approach angle natural fracture, can enhance fracture network complexity and facilitate efficient hydraulic fracturing in deep shale gas reservoirs.
- 1 April 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (4)
Fracture propagation law of shale gas horizontal wells under the influence of production stress disturbance in refracturing
During shale gas production, old wells often experience rapid capacity decline and difficulty in effectively utilizing the reservoir after the initial fracturing stimulation, which severely impacts production. The refracturing technology can reactivate low-producing wells to a certain extent through the secondary reconstruction of the residual reserve area. However, due to changes in the stress field after reservoir production, the fracture propagation law is often unclear. Therefore, this study uses a fully coupled flow-geomechanics model combined with the extended finite element method to numerically simulate the stress disturbance and refracturing fracture propagation under single- and double-fracture production scenarios. The results show that after production, the stress field near the fractures changes direction, causing the refracturing fractures to deviate significantly after initiation. As production time increases, the amplitude and range of stress deviation first increase rapidly, then decrease slowly. The fracture deviation amplitude and range follow the same trend, and the fracture pressure increases accordingly. When moving away from the production fracture, the stress deviation gradually slows down, weakening its influence on fracture propagation, and the fracture pressure increases steadily. Furthermore, during double-fracture production, as the distance between production fractures decreases, the area unaffected by stress deviation gradually shrinks. When the distance between production fractures is less than 15 m, the central region will still experience the influence of stress deviation during refracturing. In conclusion, to avoid intersection with the primary fracture during refracturing, it is recommended to choose areas far from the production fractures and with longer production times for fracturing stimulation. The simulation results can provide theoretical guidance to some extent for selecting the location and timing of perforations in field refracturing operations.
- 1 April 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (4)
Fracture propagation law of shale gas horizontal wells under the influence of production stress disturbance in refracturing
During shale gas production, old wells often experience rapid capacity decline and difficulty in effectively utilizing the reservoir after the initial fracturing stimulation, which severely impacts production. The refracturing technology can reactivate low-producing wells to a certain extent through the secondary reconstruction of the residual reserve area. However, due to changes in the stress field after reservoir production, the fracture propagation law is often unclear. Therefore, this study uses a fully coupled flow-geomechanics model combined with the extended finite element method to numerically simulate the stress disturbance and refracturing fracture propagation under single- and double-fracture production scenarios. The results show that after production, the stress field near the fractures changes direction, causing the refracturing fractures to deviate significantly after initiation. As production time increases, the amplitude and range of stress deviation first increase rapidly, then decrease slowly. The fracture deviation amplitude and range follow the same trend, and the fracture pressure increases accordingly. When moving away from the production fracture, the stress deviation gradually slows down, weakening its influence on fracture propagation, and the fracture pressure increases steadily. Furthermore, during double-fracture production, as the distance between production fractures decreases, the area unaffected by stress deviation gradually shrinks. When the distance between production fractures is less than 15 m, the central region will still experience the influence of stress deviation during refracturing. In conclusion, to avoid intersection with the primary fracture during refracturing, it is recommended to choose areas far from the production fractures and with longer production times for fracturing stimulation. The simulation results can provide theoretical guidance to some extent for selecting the location and timing of perforations in field refracturing operations.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
The propagation laws of hydraulic fractures under the influence of natural fracture zones
This paper uses the finite-discrete element method (FDEM) to establish a fluid–solid coupling model for the propagation of multi-cluster hydraulic fractures. The validity of the proposed model is verified using the analytical solution and onsite microseismic data. The results show that with the approach angle increases, the propagation of hydraulic fracture transitions from a single capture mode to the mixed modes of capture, crossing and blocking. The total length of hydraulic fractures is negatively correlated with the approach angle and cohesion of natural fracture, and positively correlated with the distribution density and bandwidth of natural fracture. The length of shear fractures initially increases and then decreases with the increase in approach angle, showing negatively, positively, and positively correlated with cohesion, length, and bandwidth, respectively, while the trend of tensile fracture length is opposite to it. The tortuosity of hydraulic fractures (which is used to characterize the complexity of fracture morphology) initially decreases and then increases with the increase in the approach angle, negatively correlated with the cohesion of natural fracture, and positively correlated with the distribution density and bandwidth of natural fractures. Comparatively, the fracture propagation morphology is the most complex at the approach angle of 45°, which is more conducive to full reservoir enhancement. Conversely, under conditions of high cohesion, narrow width, and low-density distribution of natural fractures, the fracture morphology is relatively simple, all of which are unfavorable for reservoir enhancement in the target segment.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
The propagation laws of hydraulic fractures under the influence of natural fracture zones
This paper uses the finite-discrete element method (FDEM) to establish a fluid–solid coupling model for the propagation of multi-cluster hydraulic fractures. The validity of the proposed model is verified using the analytical solution and onsite microseismic data. The results show that with the approach angle increases, the propagation of hydraulic fracture transitions from a single capture mode to the mixed modes of capture, crossing and blocking. The total length of hydraulic fractures is negatively correlated with the approach angle and cohesion of natural fracture, and positively correlated with the distribution density and bandwidth of natural fracture. The length of shear fractures initially increases and then decreases with the increase in approach angle, showing negatively, positively, and positively correlated with cohesion, length, and bandwidth, respectively, while the trend of tensile fracture length is opposite to it. The tortuosity of hydraulic fractures (which is used to characterize the complexity of fracture morphology) initially decreases and then increases with the increase in the approach angle, negatively correlated with the cohesion of natural fracture, and positively correlated with the distribution density and bandwidth of natural fractures. Comparatively, the fracture propagation morphology is the most complex at the approach angle of 45°, which is more conducive to full reservoir enhancement. Conversely, under conditions of high cohesion, narrow width, and low-density distribution of natural fractures, the fracture morphology is relatively simple, all of which are unfavorable for reservoir enhancement in the target segment.