Ming-Chi Pang
Research Subjects
Research Interests
Ming-Chi Pang has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Ziyun Wang
School of Power and Energy, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
4 shared publications - Yue Zhang
Nanjing University of Aeronautics and Astronautics
3 shared publications Hui-Jun Tan
2 shared publicationsHuijun Tan
2 shared publicationsHaicheng Zhu
1 shared publication- Hantian Zhang1 shared publication
Latest Publications
- 12 August 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 180
Scaling analysis and experimental validation for incident shock wave−compression waves/boundary layer interactions
- 12 August 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 180
Scaling analysis and experimental validation for incident shock wave−compression waves/boundary layer interactions
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Study on continuous incident compression waves/turbulent boundary layer interaction under the influence of an expansion corner
Numerical simulations were employed to investigate incident compression waves/boundary layer interactions under the influence of an expansion corner abstracted from high-speed supersonic inlets. As the incident compression waves migrate from upstream to downstream of the expansion corner, three distinct interaction patterns are identified based on the relative positions between the expansion corner and the incident compression waves, including interaction type I where the tailing compression wave remains upstream of the expansion corner, interaction type II where the expansion corner lies between the leading and tailing compression waves, and interaction type III where the leading compression wave impinges downstream of the expansion corner. Under inviscid conditions, the pressure distribution characteristics and the range of the incident compression waves along the wall were obtained for each interaction type, with predictive models for the range in interaction types II and III established through supersonic relations. Viscous simulations demonstrated that varying expansion corner angles and interaction types significantly affect wave structures around separation zones, pressure distribution characteristics, and separation zone scale. Pressure distributions conform to typical separated flow features for large separation cases. The separation zone scale showed consistent initial reduction followed by enlargement across different corner angles, which was explained by the inviscid analysis of the range of incident compression waves. Crucially, the relative positions between the sonic line and the wall were identified as a paramount factor for wave structures, enabling the development of flow models that elucidate the formation mechanisms of various wave patterns surrounding separation zones.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Study on continuous incident compression waves/turbulent boundary layer interaction under the influence of an expansion corner
Numerical simulations were employed to investigate incident compression waves/boundary layer interactions under the influence of an expansion corner abstracted from high-speed supersonic inlets. As the incident compression waves migrate from upstream to downstream of the expansion corner, three distinct interaction patterns are identified based on the relative positions between the expansion corner and the incident compression waves, including interaction type I where the tailing compression wave remains upstream of the expansion corner, interaction type II where the expansion corner lies between the leading and tailing compression waves, and interaction type III where the leading compression wave impinges downstream of the expansion corner. Under inviscid conditions, the pressure distribution characteristics and the range of the incident compression waves along the wall were obtained for each interaction type, with predictive models for the range in interaction types II and III established through supersonic relations. Viscous simulations demonstrated that varying expansion corner angles and interaction types significantly affect wave structures around separation zones, pressure distribution characteristics, and separation zone scale. Pressure distributions conform to typical separated flow features for large separation cases. The separation zone scale showed consistent initial reduction followed by enlargement across different corner angles, which was explained by the inviscid analysis of the range of incident compression waves. Crucially, the relative positions between the sonic line and the wall were identified as a paramount factor for wave structures, enabling the development of flow models that elucidate the formation mechanisms of various wave patterns surrounding separation zones.
- Open Access
- 13 August 2025
- Published by Elsevier in Chinese Journal of Aeronautics
- Vol. 39 (7)
Investigation on three-dimensional unsteady flow characteristics during TBCC inlet mode transition using fast-responding PSP
- 13 August 2025
- Published by Elsevier in Chinese Journal of Aeronautics
- Vol. 39 (7)
Open AccessInvestigation on three-dimensional unsteady flow characteristics during TBCC inlet mode transition using fast-responding PSP
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Characteristics of incident compression waves/boundary layer interaction for high-speed supersonic inlets
Interactions between the turbulent boundary layer and incident compression waves (ICWs), sufficiently strong to induce boundary layer separation, are investigated numerically and analytically. This paper proposes two typical interaction modes of ICWs and the boundary layer: one where the convergence point of the ICWs is located on a flat plate and another where the ICWs impinge on the flat plate in a dispersed manner. For the two typical interaction modes, corresponding aerodynamic profiles for ICW generators are established. The macroscopic flow structures evolve with different ICW ranges on the flat plate, and can be classified into three categories. First, when the ICWs cover a smaller range, flow structures resemble that of the interaction between a single incident shock wave and a boundary layer. Second, when the ICWs cover a moderate range, the reattachment point moves upstream to the impingement point of the terminal compression wave. In this case, the reattachment process still features a reattachment shock. Third, when the ICWs cover a large range, the reattachment shock wave degrades from a reattachment shock wave to a series of compression waves. Inviscid models of the above wave structures were established. Separation scales in two interaction modes are also investigated. Additionally, based on mass conservation within control volumes established for the interaction zones, the dimensionless interaction intensity and length for two modes are defined, and it is found that within the Mach number scope of this study, two modes exhibit different relationships between “the dimensionless interaction intensity” and “the dimensionless interaction length.”
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Characteristics of incident compression waves/boundary layer interaction for high-speed supersonic inlets
Interactions between the turbulent boundary layer and incident compression waves (ICWs), sufficiently strong to induce boundary layer separation, are investigated numerically and analytically. This paper proposes two typical interaction modes of ICWs and the boundary layer: one where the convergence point of the ICWs is located on a flat plate and another where the ICWs impinge on the flat plate in a dispersed manner. For the two typical interaction modes, corresponding aerodynamic profiles for ICW generators are established. The macroscopic flow structures evolve with different ICW ranges on the flat plate, and can be classified into three categories. First, when the ICWs cover a smaller range, flow structures resemble that of the interaction between a single incident shock wave and a boundary layer. Second, when the ICWs cover a moderate range, the reattachment point moves upstream to the impingement point of the terminal compression wave. In this case, the reattachment process still features a reattachment shock. Third, when the ICWs cover a large range, the reattachment shock wave degrades from a reattachment shock wave to a series of compression waves. Inviscid models of the above wave structures were established. Separation scales in two interaction modes are also investigated. Additionally, based on mass conservation within control volumes established for the interaction zones, the dimensionless interaction intensity and length for two modes are defined, and it is found that within the Mach number scope of this study, two modes exhibit different relationships between “the dimensionless interaction intensity” and “the dimensionless interaction length.”