Ivan P. Storozhuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ivan P. Storozhuk has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Alexander G. Khina
Department of Chemistry, M. V. Lomonosov Moscow State University, Moscow 119991, Russia
3 shared publications A. S. Kuleznev
NTI Center “Digital Materials Science: New Materials and Substances”, Bauman Moscow State Technical University, Moscow, Russia
2 shared publicationsD. P. Bulkatov
NTI Center “Digital Materials Science: New Materials and Substances”, Bauman Moscow State Technical University, Moscow, Russia
2 shared publications- Denis P. Bulkatov
NTI Center “Digital Materials Science: New Materials and Substances”, Bauman Moscow State Technical University, Moscow 105005, Russia
2 shared publications V. S. Buryakov
NTI Center “Digital Materials Science: New Materials and Substances”, Bauman Moscow State Technical University, Moscow, Russia
2 shared publicationsA. G. Khina
National Technology Initiative Center “Digital Materials Science: New Materials and Substances,” Bauman Moscow State Technical University, Moscow, Russia
1 shared publication
Latest Publications
- Open Access
Lunar Regolith Simulant–Filled High-Performance Thermoplastic Composites for Lunar Construction and Their Potential for Additive Manufacturing
The use of lunar regolith (LR) for lunar construction is a key route to reducing the mass of materials transported from Earth. In this work, highly filled composites based on polyphenylsulfone (PPSU) with Tg = 219.1 °C and modified polyetherimide (PEI) with Tg = 247.1 °C containing up to 92.5 wt.% of LR simulant were prepared by dry blending the LR simulant and the polymer powders, followed by hot pressing. Their internal structure, mechanical, thermal, thermomechanical, and melt/flow properties were evaluated. The properties of the composites strongly depended on the LR simulant content and were governed by two competing mechanisms: restriction of polymer-chain mobility and of matrix deformation by the rigid mineral filler at moderate LR simulant contents, and increased porosity and loss of matrix continuity caused by binder deficiency at excessive filler loadings. At LR simulant contents of up to 60 wt.% for PPSU and 85 wt.% for PEI, dense, low-porosity (−6 K−1 and 10.1 × 10−6 K−1 for PPSU- and PEI-based composites, respectively. Composites containing 50–60 wt.% of LR simulant retained melt/flow capability, indicating their potential suitability for processing by melt extrusion and additive manufacturing. Based on the obtained data, recommendations were formulated for application of the developed composites in melt-based 3D printing of complex-geometry parts and hot-pressed simple-shape construction elements.
Open AccessLunar Regolith Simulant–Filled High-Performance Thermoplastic Composites for Lunar Construction and Their Potential for Additive Manufacturing
The use of lunar regolith (LR) for lunar construction is a key route to reducing the mass of materials transported from Earth. In this work, highly filled composites based on polyphenylsulfone (PPSU) with Tg = 219.1 °C and modified polyetherimide (PEI) with Tg = 247.1 °C containing up to 92.5 wt.% of LR simulant were prepared by dry blending the LR simulant and the polymer powders, followed by hot pressing. Their internal structure, mechanical, thermal, thermomechanical, and melt/flow properties were evaluated. The properties of the composites strongly depended on the LR simulant content and were governed by two competing mechanisms: restriction of polymer-chain mobility and of matrix deformation by the rigid mineral filler at moderate LR simulant contents, and increased porosity and loss of matrix continuity caused by binder deficiency at excessive filler loadings. At LR simulant contents of up to 60 wt.% for PPSU and 85 wt.% for PEI, dense, low-porosity (−6 K−1 and 10.1 × 10−6 K−1 for PPSU- and PEI-based composites, respectively. Composites containing 50–60 wt.% of LR simulant retained melt/flow capability, indicating their potential suitability for processing by melt extrusion and additive manufacturing. Based on the obtained data, recommendations were formulated for application of the developed composites in melt-based 3D printing of complex-geometry parts and hot-pressed simple-shape construction elements.
- Top Cited PapersOpen Access
Coefficient of Linear Thermal Expansion of Polymers and Polymer Composites: A Comprehensive Review
This work presents a comprehensive literature review of the coefficient of linear thermal expansion (CLTE) of polymers and polymer composite materials (PCMs). It systematizes CLTE measurement methods for isotropic and anisotropic materials, including contact techniques such as dilatometry and thermomechanical analysis and non-contact methods such as digital image correlation, laser interferometry, diffraction-based techniques, and strain-gauge methods, with attention to their accuracy and fields of applicability. Furthermore, the review describes the principal mathemaical modeling approaches used to predict the CLTE of polymers and PCMs. The review also provides a comparative analysis of CLTE values for a broad range of thermoplastics (commodity, engineering, and high-performance grades) and thermosets, identifying the key factors that govern CLTE, such as the transition from the glassy to the viscous-flow state, the presence and anisotropy of a crystalline phase, and related structure–property effects. Special consideration is given to the factors determining the CLTE of polymer composites, including the properties of the polymer matrix, the nature, size, orientation and surface treatment of the filler, the architecture and reinforcement scheme of the composite, and the manufacturing process. The review also outlines application areas in which PCMs with controlled or reduced CLTE are required and illustrates these with specific examples. Thus, the article provides integrated view of the CLTE of polymers and PCMs, compiles reference data for CLTE values of various polymers and common composite fillers and offers practical recommendations for selecting polymer materials for fabricating goods that require high thermal dimensional stability.
Top Cited PapersOpen AccessCoefficient of Linear Thermal Expansion of Polymers and Polymer Composites: A Comprehensive Review
This work presents a comprehensive literature review of the coefficient of linear thermal expansion (CLTE) of polymers and polymer composite materials (PCMs). It systematizes CLTE measurement methods for isotropic and anisotropic materials, including contact techniques such as dilatometry and thermomechanical analysis and non-contact methods such as digital image correlation, laser interferometry, diffraction-based techniques, and strain-gauge methods, with attention to their accuracy and fields of applicability. Furthermore, the review describes the principal mathemaical modeling approaches used to predict the CLTE of polymers and PCMs. The review also provides a comparative analysis of CLTE values for a broad range of thermoplastics (commodity, engineering, and high-performance grades) and thermosets, identifying the key factors that govern CLTE, such as the transition from the glassy to the viscous-flow state, the presence and anisotropy of a crystalline phase, and related structure–property effects. Special consideration is given to the factors determining the CLTE of polymer composites, including the properties of the polymer matrix, the nature, size, orientation and surface treatment of the filler, the architecture and reinforcement scheme of the composite, and the manufacturing process. The review also outlines application areas in which PCMs with controlled or reduced CLTE are required and illustrates these with specific examples. Thus, the article provides integrated view of the CLTE of polymers and PCMs, compiles reference data for CLTE values of various polymers and common composite fillers and offers practical recommendations for selecting polymer materials for fabricating goods that require high thermal dimensional stability.
- 1 February 2025
- Published by Pleiades Publishing Ltd in Polymer Science, Series B
- Vol. 67 (1) , 1-12
Novel Melt-Processible Copolyetherimides Based on 4,4'-Diaminodiphenylmethane: Synthesis and Study
The first synthesis of polyetherimides (PEIs) of a copolymer structure based on bisphenol-A 4,4'‑diphthalic anhydride and methylenedianiline, containing 10 to 100 mol % of rigid-chain fragments of benzophenone (BPDA) and pyromellitic (PMDA) dianhydrides, is described. The resulting polymers were analyzed using IR spectrometry, gel permeation chromatography, differential scanning calorimetry, thermogravimetric analysis and melt flow index measurements. Quantitative characteristics of the heat-resistance and processability indicators of synthesized PEIs depending on the content of rigid-chain fragments have been determined. Results show that increasing the content of BPDA and PMDA units in the PEI structure enhances the heat resistance and thermal stability of the polymers, although the melt flow index decreases. The explanation of the observed effect based on the growth of intermolecular interaction and the formation of a crystalline phase is given. Optimal ratios of precursor dianhydrides were identified to achieve the best balance of heat resistance and processability. The resulting PEIs of optimal structure have glass transition and thermal destruction temperatures up to 25–40°C higher in comparison with unmodified PEI whilst retaining the ability to be processed through the melt. The obtained results open up broad application prospects of the developed co-PEIs as highly heat-resistant engineering thermoplastic materials.
- 1 February 2025
- Published by Pleiades Publishing Ltd in Polymer Science, Series B
- Vol. 67 (1) , 1-12
Novel Melt-Processible Copolyetherimides Based on 4,4'-Diaminodiphenylmethane: Synthesis and Study
The first synthesis of polyetherimides (PEIs) of a copolymer structure based on bisphenol-A 4,4'‑diphthalic anhydride and methylenedianiline, containing 10 to 100 mol % of rigid-chain fragments of benzophenone (BPDA) and pyromellitic (PMDA) dianhydrides, is described. The resulting polymers were analyzed using IR spectrometry, gel permeation chromatography, differential scanning calorimetry, thermogravimetric analysis and melt flow index measurements. Quantitative characteristics of the heat-resistance and processability indicators of synthesized PEIs depending on the content of rigid-chain fragments have been determined. Results show that increasing the content of BPDA and PMDA units in the PEI structure enhances the heat resistance and thermal stability of the polymers, although the melt flow index decreases. The explanation of the observed effect based on the growth of intermolecular interaction and the formation of a crystalline phase is given. Optimal ratios of precursor dianhydrides were identified to achieve the best balance of heat resistance and processability. The resulting PEIs of optimal structure have glass transition and thermal destruction temperatures up to 25–40°C higher in comparison with unmodified PEI whilst retaining the ability to be processed through the melt. The obtained results open up broad application prospects of the developed co-PEIs as highly heat-resistant engineering thermoplastic materials.
- 1 August 2024
- Published by Pleiades Publishing Ltd in Polymer Science, Series B
- Vol. 66 (4) , 514-523
Development of Polyethersulfones for Modification of Epoxy Resins
The synthesis of polyethersulfones of various chemical structures from commercially available starting materials is described. Quantitative characteristics of the dependences of the polycondensation degree and the molecular weight of the obtained polyethersulfones to the reactant ratio have been determined. The dependenses of the heat resistance of the obtained materials on the molecular weight and rigid-chain moieties introduced into the structure of the polymers have been revealed. The effect of the concentration and the reactivity of the end groups of macromolecules on the thermo-oxidative stability of the product polyethersulfones is shown. The particular attention is paid to the synthesis of polyethersulfones with phenolic end groups and a polycondensation degree of n = 25‒30. Such polymers have a high (up to 20 wt %) solubility in epoxy oligomers upon heating without a significant increase in the viscosity of the epoxy resins and do not form an insoluble phase upon binder cooling, thereby opening up broad prospects for their further use as epoxy modifiers.
- 1 August 2024
- Published by Pleiades Publishing Ltd in Polymer Science, Series B
- Vol. 66 (4) , 514-523
Development of Polyethersulfones for Modification of Epoxy Resins
The synthesis of polyethersulfones of various chemical structures from commercially available starting materials is described. Quantitative characteristics of the dependences of the polycondensation degree and the molecular weight of the obtained polyethersulfones to the reactant ratio have been determined. The dependenses of the heat resistance of the obtained materials on the molecular weight and rigid-chain moieties introduced into the structure of the polymers have been revealed. The effect of the concentration and the reactivity of the end groups of macromolecules on the thermo-oxidative stability of the product polyethersulfones is shown. The particular attention is paid to the synthesis of polyethersulfones with phenolic end groups and a polycondensation degree of n = 25‒30. Such polymers have a high (up to 20 wt %) solubility in epoxy oligomers upon heating without a significant increase in the viscosity of the epoxy resins and do not form an insoluble phase upon binder cooling, thereby opening up broad prospects for their further use as epoxy modifiers.