Florian Klapal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Florian Klapal has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Mark Werner Hlawitschka
Institute of Process Engineering, Johannes Kepler University Linz, Linz, Austria
2 shared publications - Jonáš Dařílek1 shared publication
- Manuel C. J. Schachinger
School of Engineering, University of Applied Sciences Upper Austria, Stelzhamerstraße 23, 4600 Wels, Austria
1 shared publication - Markus Wierer
Institute for Analytical Chemistry, Johannes Kepler University Linz, Altenbergerstrasse 69, 4020 Linz, Austria
1 shared publication - Stefanie Flatscher
Institute of Process Engineering, Johannes Kepler University Linz, Altenberger Strasse 69, Linz 4040, Austria
1 shared publication
Latest Publications
- Open Access
- 9 September 2026
- Published by Elsevier in SSRN Electronic Journal
Carbonate Supply Pathway and Sparger Design as Control Parameters in Li2CO3 Reactive Crystallisation from Li2SO4
Lithium carbonate is an important commercial lithium product and precursor for batterygrade materials. Replacing conventional Na2CO3-based precipitation with CO2-based carbonate generation may couple lithium recovery with CO2 utilisation, but the effects of carbonate supply pathway and hydrodynamic control on recoverypurity tradeoffs remain insufficiently clarified. In this study, solid-liquid, liquid-liquid/slurry, and gas-liquid precipitation routes were compared at laboratoryscale using solutions with a concentration of 20 g L-1 Li. Hydrodynamic control was then investigated in a technicalscale column by varying sparger pore size between 1.0, 1.5 and 2.5 mm. At laboratoryscale, the liquid-liquid/slurry route achieved 74% Li2CO3-based lithium recovery, but the lowest purity of 79% Li2CO3. The solidliquid route provided a better recovery-purity balance, with 70% recovery and 87% purity. Gasliquid precipitation at 5 M NaOH was limited by the hydroxide inventory required for the carbonate formation, giving recovery rates of 22-25%, whereas 20 M NaOH shifted speciation towards CO32- and raised recovery to 80% at 87% purity. At technicalscale, the 1.0 and 1.5 mm spargers gave comparable CO2 uptake of 182 and 179 L, while the 2.5 mm sparger reduced CO2 uptake to 99 L. The 1.5 mm sparger provided the most favourable compromise, achieving 61% recovery and 88% purity. Overall, carbonate supply pathway, alkalinity and sparger design jointly determine the recoverypurity balance in scalable CO2 based Li2CO3 precipitation.
- 9 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCarbonate Supply Pathway and Sparger Design as Control Parameters in Li2CO3 Reactive Crystallisation from Li2SO4
Lithium carbonate is an important commercial lithium product and precursor for batterygrade materials. Replacing conventional Na2CO3-based precipitation with CO2-based carbonate generation may couple lithium recovery with CO2 utilisation, but the effects of carbonate supply pathway and hydrodynamic control on recoverypurity tradeoffs remain insufficiently clarified. In this study, solid-liquid, liquid-liquid/slurry, and gas-liquid precipitation routes were compared at laboratoryscale using solutions with a concentration of 20 g L-1 Li. Hydrodynamic control was then investigated in a technicalscale column by varying sparger pore size between 1.0, 1.5 and 2.5 mm. At laboratoryscale, the liquid-liquid/slurry route achieved 74% Li2CO3-based lithium recovery, but the lowest purity of 79% Li2CO3. The solidliquid route provided a better recovery-purity balance, with 70% recovery and 87% purity. Gasliquid precipitation at 5 M NaOH was limited by the hydroxide inventory required for the carbonate formation, giving recovery rates of 22-25%, whereas 20 M NaOH shifted speciation towards CO32- and raised recovery to 80% at 87% purity. At technicalscale, the 1.0 and 1.5 mm spargers gave comparable CO2 uptake of 182 and 179 L, while the 2.5 mm sparger reduced CO2 uptake to 99 L. The 1.5 mm sparger provided the most favourable compromise, achieving 61% recovery and 88% purity. Overall, carbonate supply pathway, alkalinity and sparger design jointly determine the recoverypurity balance in scalable CO2 based Li2CO3 precipitation.
- Open Access
Towards Efficient Bio-Methanation: A Comparative Analysis of Disperser Designs and Process Optimization in Bubble Columns
This study aims to contribute to the optimization of bio-methanation in bubble columns, making it a more viable alternative to stirred tank reactors. The primary challenge to be addressed is the enhancement of mass transfer, which strongly depends on parameters such as bubble size and gas hold-up. Various disperser designs were examined in a 0.14 mm diameter column, comparing their performance in terms of bubble diameter distribution and gas hold-up. The results indicate that an optimized plate disperser featuring a porous structure outperformed other designs by maintaining high gas retention without significant coalescence. Additionally, newly developed plug-in dispersers allowed for counter-current flow operation, enhancing process flexibility. Commercially available porous pin dispersers produced smaller bubbles compared to the other designs, yielding high gas hold-ups at lower gas velocities. Correlations between disperser type and column design parameters were established, laying the foundation for apparatus optimization. The findings contribute to the development of digital twin models, facilitating the refinement of bio-methanation processes within bubble columns for increased efficiency.
Open AccessTowards Efficient Bio-Methanation: A Comparative Analysis of Disperser Designs and Process Optimization in Bubble Columns
This study aims to contribute to the optimization of bio-methanation in bubble columns, making it a more viable alternative to stirred tank reactors. The primary challenge to be addressed is the enhancement of mass transfer, which strongly depends on parameters such as bubble size and gas hold-up. Various disperser designs were examined in a 0.14 mm diameter column, comparing their performance in terms of bubble diameter distribution and gas hold-up. The results indicate that an optimized plate disperser featuring a porous structure outperformed other designs by maintaining high gas retention without significant coalescence. Additionally, newly developed plug-in dispersers allowed for counter-current flow operation, enhancing process flexibility. Commercially available porous pin dispersers produced smaller bubbles compared to the other designs, yielding high gas hold-ups at lower gas velocities. Correlations between disperser type and column design parameters were established, laying the foundation for apparatus optimization. The findings contribute to the development of digital twin models, facilitating the refinement of bio-methanation processes within bubble columns for increased efficiency.