Gaël Berthet
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gaël Berthet has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Seungyong Hahn
Seoul National University
7 shared publications - Wonju Jung
Department of Electrical and Computer Engineering, Seoul National University, Seoul, Republic of Korea
6 shared publications - Hyunsoo Park
Department of Electrical and Computer Engineering, Seoul National University, Seoul, Republic of Korea
5 shared publications - Wonseok Jang
Department of Electrical and Computer Engineering, Seoul National University, Seoul, Republic of Korea
5 shared publications - Jeonghwan Park
Applied Superconductivity Center, Electric Power Research Institute, Seoul National University, Seoul, Republic of Korea
4 shared publications - Sangjin Lee
Applied Superconductivity Center, Electric Power Research Institute, Seoul National University, Seoul, Republic of Korea
4 shared publications
Latest Publications
- 29 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Fabrication and Test of a Cryogen-Free Bi-2212 Magnet Prototype for Solid-State Spin Qubit Applications
Solid-state spin qubit experiments for quantum technology require highly stable and temporally homogeneous magnetic fields. While permanent magnets are commonly used, their performance is limited by sensitivity to temperature fluctuations and field strength. To address these challenges, this work explores the use of a cryogen-free Bi-2212 superconducting magnet as a viable alternative. The fabrication and test of a prototype magnet are presented. Two initial coils (Coil A and Coil B) were fabricated to investigate current lead assembly methods, revealing bonding and oxidation issues with Inconel 600 and copper components. A refined fabrication process was developed and validated using a third coil (Coil C), which successfully underwent heat treatment and current lead assembly. Coil C was cooled to below 12 K using a cryocooler and operated at currents up to 150 A. Nonlinear behaviors in terminal voltage and magnetic field were observed and attributed to the ferromagnetic response of the Inconel 600 bobbin at cryogenic temperatures. These effects were modeled using an empirically derived B-H curve, showing reasonable agreement with simulation. The results demonstrate the feasibility of cryogen-free Bi-2212 magnets for quantum applications and establish a reliable fabrication method for future scaling.
- 29 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Fabrication and Test of a Cryogen-Free Bi-2212 Magnet Prototype for Solid-State Spin Qubit Applications
Solid-state spin qubit experiments for quantum technology require highly stable and temporally homogeneous magnetic fields. While permanent magnets are commonly used, their performance is limited by sensitivity to temperature fluctuations and field strength. To address these challenges, this work explores the use of a cryogen-free Bi-2212 superconducting magnet as a viable alternative. The fabrication and test of a prototype magnet are presented. Two initial coils (Coil A and Coil B) were fabricated to investigate current lead assembly methods, revealing bonding and oxidation issues with Inconel 600 and copper components. A refined fabrication process was developed and validated using a third coil (Coil C), which successfully underwent heat treatment and current lead assembly. Coil C was cooled to below 12 K using a cryocooler and operated at currents up to 150 A. Nonlinear behaviors in terminal voltage and magnetic field were observed and attributed to the ferromagnetic response of the Inconel 600 bobbin at cryogenic temperatures. These effects were modeled using an empirically derived B-H curve, showing reasonable agreement with simulation. The results demonstrate the feasibility of cryogen-free Bi-2212 magnets for quantum applications and establish a reliable fabrication method for future scaling.
- 12 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-7
Inter-Tape Contact Resistance Characterization of Soldered Stacked-Tape Cable Samples in Liquid Nitrogen
We experimentally measured and numerically modeled inter-tape contact resistance in reduced-scale soldered tape stacks. Nine cable-type specimens—seven 30 cm-long samples with 30 or 69 of 4 mm-wide REBCO tapes and two 100 cm-long samples with 104 and 106 of 12 mm-wide tapes—were manually fabricated using pre-cut long REBCO tapes to facilitate four-point voltage measurements. Measured inter-tape resistivities ranged from 30 n$\Omega$ $\cdot$ m to 733 n$\Omega$ $\cdot$ m, with the best soldered stacks averaged 47 n$\Omega$ $\cdot$ m whereas the unsoldered and poorly soldered cases averaged 516 n$\Omega$ $\cdot$ m and 683 n$\Omega$$\cdot$ m. A two-dimensional finite-element model assuming perfectly aligned tapes and tunable solder resistivity reproduced these trends, confirming the dominant role of edge-solder conductivity in reducing contact resistance. Cross-sectional microscopy corroborated the link between solder distribution and electrical performance, showing that edge-solder voids are the primary resistance driver. This combined methodology provides a practical framework for quality control and design optimization of high-current HTS cables in fusion magnet applications.
- 12 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-7
Inter-Tape Contact Resistance Characterization of Soldered Stacked-Tape Cable Samples in Liquid Nitrogen
We experimentally measured and numerically modeled inter-tape contact resistance in reduced-scale soldered tape stacks. Nine cable-type specimens—seven 30 cm-long samples with 30 or 69 of 4 mm-wide REBCO tapes and two 100 cm-long samples with 104 and 106 of 12 mm-wide tapes—were manually fabricated using pre-cut long REBCO tapes to facilitate four-point voltage measurements. Measured inter-tape resistivities ranged from 30 n$\Omega$ $\cdot$ m to 733 n$\Omega$ $\cdot$ m, with the best soldered stacks averaged 47 n$\Omega$ $\cdot$ m whereas the unsoldered and poorly soldered cases averaged 516 n$\Omega$ $\cdot$ m and 683 n$\Omega$$\cdot$ m. A two-dimensional finite-element model assuming perfectly aligned tapes and tunable solder resistivity reproduced these trends, confirming the dominant role of edge-solder conductivity in reducing contact resistance. Cross-sectional microscopy corroborated the link between solder distribution and electrical performance, showing that edge-solder voids are the primary resistance driver. This combined methodology provides a practical framework for quality control and design optimization of high-current HTS cables in fusion magnet applications.
- 26 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Aging Effects in REBCO Tapes Solder Joint Made With Indium-Tin
With the promises of nuclear fusion, an increasing number of fusion magnet projects are employing $\mathrm{(RE)Ba}_{2}\text{Cu}_{3}\mathrm{O}_{7-\updelta}$ (REBCO) tapes. These magnets often include multiple demountable joints, which typically incorporate low-temperature solder either in the joint itself or in the cable. Such solders usually contain elements that diffuse readily in copper, raising concerns about the aging effects. This study investigates the impact of the InterMetallic-Compound (IMC) growth on the joints properties through room-temperature aging and annealing. Eutectic indium-tin solder joints stored for nine months in a desiccator did not exhibit any significant change in their properties. Given the strong temperature dependence of the IMC growth, annealing at 100°C was performed to simulate long-term effects. After 6 to 8 days of annealing, critical current degradation was measured in all samples containing solder, indicating that the IMC had grown to the REBCO layer deteriorating it. Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS) analyses revealed that even after 20 days, solder elements reached the REBCO layer only in regions where the solder was abundant.
- 26 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Aging Effects in REBCO Tapes Solder Joint Made With Indium-Tin
With the promises of nuclear fusion, an increasing number of fusion magnet projects are employing $\mathrm{(RE)Ba}_{2}\text{Cu}_{3}\mathrm{O}_{7-\updelta}$ (REBCO) tapes. These magnets often include multiple demountable joints, which typically incorporate low-temperature solder either in the joint itself or in the cable. Such solders usually contain elements that diffuse readily in copper, raising concerns about the aging effects. This study investigates the impact of the InterMetallic-Compound (IMC) growth on the joints properties through room-temperature aging and annealing. Eutectic indium-tin solder joints stored for nine months in a desiccator did not exhibit any significant change in their properties. Given the strong temperature dependence of the IMC growth, annealing at 100°C was performed to simulate long-term effects. After 6 to 8 days of annealing, critical current degradation was measured in all samples containing solder, indicating that the IMC had grown to the REBCO layer deteriorating it. Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS) analyses revealed that even after 20 days, solder elements reached the REBCO layer only in regions where the solder was abundant.
- 19 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Design, Construction, and Experiment of Roller Shaped High-Temperature Superconducting Coil Joint Apparatus
The fabrication of high-temperature superconductor (HTS) magnets often involves manual soldering joints, which relies on operator skill and causes performance variations. To address these challenges, this study presents the design, construction, and experimental evaluation of a roller-shaped HTS coil joint apparatus for soldering rare-earth barium copper oxide (REBCO) tapes. The apparatus was developed to facilitate the soldering process across various coil dimensions, ensuring high performance and reliable joints between HTS coils. First, simulations and analyses were conducted to ensure the thermal and mechanical requirements based on prior REBCO tape-to-tape joint researches. The apparatus is equipped with functionalities to control parameters such as solder type, target temperature, heating rate, holding time, cooling time, and pressure. Then, the constructed joint apparatus was primarily utilized to validate the tape-to-tape soldering process, with a focus on maintaining consistent electro-mechanical performance. Finally, experimental evaluations of HTS coil-to-coil joints evaluations demonstrated the ability to achieve high performance and reliability joint, highlighting its potential for applications in advanced HTS REBCO magnet systems.
- 19 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Design, Construction, and Experiment of Roller Shaped High-Temperature Superconducting Coil Joint Apparatus
The fabrication of high-temperature superconductor (HTS) magnets often involves manual soldering joints, which relies on operator skill and causes performance variations. To address these challenges, this study presents the design, construction, and experimental evaluation of a roller-shaped HTS coil joint apparatus for soldering rare-earth barium copper oxide (REBCO) tapes. The apparatus was developed to facilitate the soldering process across various coil dimensions, ensuring high performance and reliable joints between HTS coils. First, simulations and analyses were conducted to ensure the thermal and mechanical requirements based on prior REBCO tape-to-tape joint researches. The apparatus is equipped with functionalities to control parameters such as solder type, target temperature, heating rate, holding time, cooling time, and pressure. Then, the constructed joint apparatus was primarily utilized to validate the tape-to-tape soldering process, with a focus on maintaining consistent electro-mechanical performance. Finally, experimental evaluations of HTS coil-to-coil joints evaluations demonstrated the ability to achieve high performance and reliability joint, highlighting its potential for applications in advanced HTS REBCO magnet systems.
- 4 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Experimental Study on Temperature-Controlled Charging Sequence for Reduction of Screening Current Effect in HTS Magnet
High-temperature superconductor (HTS) rare-earth barium copper oxide (REBCO) conductor has been extensively researched and developed for various applications. However, due to the intrinsic properties of REBCO conductors, the screening current occurs and this effect causes induced field and stress in superconducting magnets. Therefore, we investigated a strategy to mitigate the screening current effect in HTS magnets with the simultaneous control of temperature and current. In this paper, we ramped up the coil and measured the magnetic field of the HTS magnet as a references on conduction cooling system within different temperature: 20 K and 50 K. Then, the temperature-controlled charging sequence method with PID control was conducted so that the current ramping up simultaneously started with the magnet cool down: (1) 50 K to 20 K and (2) 80 K to 50 K. Finally, we analyzed the experiment results of the magnetic field distribution compared to reference charging values. These results showed the possibility to develop the operating techniques for high-field REBCO magnets that reduce the screening current induced field.
- 4 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Experimental Study on Temperature-Controlled Charging Sequence for Reduction of Screening Current Effect in HTS Magnet
High-temperature superconductor (HTS) rare-earth barium copper oxide (REBCO) conductor has been extensively researched and developed for various applications. However, due to the intrinsic properties of REBCO conductors, the screening current occurs and this effect causes induced field and stress in superconducting magnets. Therefore, we investigated a strategy to mitigate the screening current effect in HTS magnets with the simultaneous control of temperature and current. In this paper, we ramped up the coil and measured the magnetic field of the HTS magnet as a references on conduction cooling system within different temperature: 20 K and 50 K. Then, the temperature-controlled charging sequence method with PID control was conducted so that the current ramping up simultaneously started with the magnet cool down: (1) 50 K to 20 K and (2) 80 K to 50 K. Finally, we analyzed the experiment results of the magnetic field distribution compared to reference charging values. These results showed the possibility to develop the operating techniques for high-field REBCO magnets that reduce the screening current induced field.
- 24 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Comparison of the Electrical Properties of Copper Diffusion-Bonded Joints and Solder Joints for $\mathrm{(RE)Ba}_{2}\text{Cu}_{3}\mathrm{O}_{7-\delta }$ TapesHTS tapes are central to many future technologies and, as such, are the subject of significant research aimed to improve their properties. The production of long and high-quality $\mathrm{(RE)Ba}_{2}\text{Cu}_{3}\mathrm{O}_{7-\delta }$ (REBCO) tapes being a challenging task, spools commercially available tend to be relatively short. Therefore, joints are critical points during applications, prompting extensive efforts to develop joints with low resistivity and good mechanical properties. Consequently, this study focuses on the recently developed copper diffusion bonding (diff. bond.) method. Using three different spools, the properties of the copper diff. bond. joints are compared to the solder joints. The results indicate that copper diff. bond. joints generally have lower surface resistivity compared to their soldered counterparts. Additionally, the results also showed a slightly better repeatability in joints resistance compared to the solder joints. On the other hand, one spool gave contradictory results having lower joint resistance and better repeatability for the soldering method which could not be explained.
- 24 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Comparison of the Electrical Properties of Copper Diffusion-Bonded Joints and Solder Joints for $\mathrm{(RE)Ba}_{2}\text{Cu}_{3}\mathrm{O}_{7-\delta }$ TapesHTS tapes are central to many future technologies and, as such, are the subject of significant research aimed to improve their properties. The production of long and high-quality $\mathrm{(RE)Ba}_{2}\text{Cu}_{3}\mathrm{O}_{7-\delta }$ (REBCO) tapes being a challenging task, spools commercially available tend to be relatively short. Therefore, joints are critical points during applications, prompting extensive efforts to develop joints with low resistivity and good mechanical properties. Consequently, this study focuses on the recently developed copper diffusion bonding (diff. bond.) method. Using three different spools, the properties of the copper diff. bond. joints are compared to the solder joints. The results indicate that copper diff. bond. joints generally have lower surface resistivity compared to their soldered counterparts. Additionally, the results also showed a slightly better repeatability in joints resistance compared to the solder joints. On the other hand, one spool gave contradictory results having lower joint resistance and better repeatability for the soldering method which could not be explained.
- 20 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Experimental Study on Shrink-Fitted REBCO Pancake Coils
This study focuses on two challenges associated with pancake-wound REBCO magnets: 1) mechanical damage in module coils 2) issues related to electrical joint implementation. Shrink-fitting an external ring structure around the pancake coil can resolve the problems by inducing compressive radial and hoop stress, opposing magnetic stress. Moreover, the ring can serve as an electrical joint between pancake coils, facilitating the easy replacement of malfunctioning module coils within this joint structure. In this study, we fabricated a small pancake wound no-insulation magnet with copper shrink-fit joints. Each pancake is surrounded by a ring-shaped copper structure with a rectangular cross-section, achieved through shrink-fitting. We present detailed manufacturing procedures and measured contact resistances. The result demonstrates that shrink-fitting can be applied to pancake wound magnets and perform novel modular design and mechanical reinforcement. This experiment suggests a new approach to implementing electric connection and reinforcement in REBCO pancake-wound magnets.
- 20 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Experimental Study on Shrink-Fitted REBCO Pancake Coils
This study focuses on two challenges associated with pancake-wound REBCO magnets: 1) mechanical damage in module coils 2) issues related to electrical joint implementation. Shrink-fitting an external ring structure around the pancake coil can resolve the problems by inducing compressive radial and hoop stress, opposing magnetic stress. Moreover, the ring can serve as an electrical joint between pancake coils, facilitating the easy replacement of malfunctioning module coils within this joint structure. In this study, we fabricated a small pancake wound no-insulation magnet with copper shrink-fit joints. Each pancake is surrounded by a ring-shaped copper structure with a rectangular cross-section, achieved through shrink-fitting. We present detailed manufacturing procedures and measured contact resistances. The result demonstrates that shrink-fitting can be applied to pancake wound magnets and perform novel modular design and mechanical reinforcement. This experiment suggests a new approach to implementing electric connection and reinforcement in REBCO pancake-wound magnets.