Hadi Goudarzhagh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hadi Goudarzhagh has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Seyed Hamid Fathi
Department of Electrical Engineering, Amirkabir University of Technology, Tehran, Iran
4 shared publications - Edris Pouresmaeil
Aalto University
2 shared publications - Sobhan Heidarbozorg
Department of Electrical Engineering, Amirkabir University of Technology, Tehran Polytechnic, Tehran, Iran
2 shared publications - Ebrahim Babaei
Faculty of Electrical and Computer Engineering, University of Tabriz, Tabriz, Iran
1 shared publication - Gevork Babamalek Gharehpetian
Amirkabir University of Technology
1 shared publication - Mehran Sabahi
University of Tabriz
1 shared publication
Latest Publications
- Open Access
- 19 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 7, 1075-1086
Dual-Input Dual-Output Split-Source Inverter With Low Input Current Ripple
This paper presents a new dual-input dual-output split-source inverter (DIDO-SSI) topology. The proposed converter boosts two independent DC inputs to higher voltage levels and feeds a nine-switch inverter (NSI) stage. The DC-side split-source network provides voltage boost capability, while buck operation is inherently achieved through the inverter modulation at the AC output stage. Consequently, the proposed topology offers buck-boost capability. Additionally, a modified pulse-width modulation (MPWM) strategy is introduced to independently control the voltage amplitude, phase, and frequency of each three-phase output. In addition, the MPWM method effectively eliminates the propagation of output frequency components into the input currents and enables flexible power-sharing control between the two input sources. The proposed topology achieves a dual-input dual-output structure equivalent to two conventional split-source inverters while using only nine switches instead of twelve. It can also operate with a single input source to supply both outputs, enhancing reliability. Moreover, utilizing both input sources increases the effective input voltage of the NSI stage. Comprehensive theoretical analysis and comparative studies demonstrate the advantages of the proposed design over existing dual-output inverter configurations and systems based on two single-output inverters, making it suitable for a wide range of single- or dual-input and dual-output inverter applications. Finally, simulation and experimental results obtained from a 525 W prototype verify the theoretical analysis.
- 19 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 7, 1075-1086
Open AccessDual-Input Dual-Output Split-Source Inverter With Low Input Current Ripple
This paper presents a new dual-input dual-output split-source inverter (DIDO-SSI) topology. The proposed converter boosts two independent DC inputs to higher voltage levels and feeds a nine-switch inverter (NSI) stage. The DC-side split-source network provides voltage boost capability, while buck operation is inherently achieved through the inverter modulation at the AC output stage. Consequently, the proposed topology offers buck-boost capability. Additionally, a modified pulse-width modulation (MPWM) strategy is introduced to independently control the voltage amplitude, phase, and frequency of each three-phase output. In addition, the MPWM method effectively eliminates the propagation of output frequency components into the input currents and enables flexible power-sharing control between the two input sources. The proposed topology achieves a dual-input dual-output structure equivalent to two conventional split-source inverters while using only nine switches instead of twelve. It can also operate with a single input source to supply both outputs, enhancing reliability. Moreover, utilizing both input sources increases the effective input voltage of the NSI stage. Comprehensive theoretical analysis and comparative studies demonstrate the advantages of the proposed design over existing dual-output inverter configurations and systems based on two single-output inverters, making it suitable for a wide range of single- or dual-input and dual-output inverter applications. Finally, simulation and experimental results obtained from a 525 W prototype verify the theoretical analysis.
- 6 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (8) , 11476-11487
A Novel High Step-Up Nonisolated Quadratic Boost Converter for Integration of Photovoltaic and Fuel-Cell Systems Into Bipolar DC Microgrids
This article proposes a two switch high-voltage-gain quadratic boost (QB) DC–DC converter, utilizing voltage multiplier techniques using a built-in transformer to increase the voltage gain and provide bipolar output. The topology of the proposed converter offers continuous input current (CIC) as well as a common ground (CG) between the input source and the output neutral point. The maximum voltage stress on the switches is a quarter of the total output voltage. The voltage gain versus duty cycle and voltage stress on switches can be improved by increasing the turn ratios of built-in transformer. Theoretical analysis and experimental results are provided based on a 400 W prototype with ${\rm \pm}$ 280 V output voltage from a 30 V DC source with an efficiency of 93.3%. The aforementioned characteristics make the converter well suited for use as an interface between renewable energy sources, such as photovoltaic or fuel cell systems, and bipolar DC microgrids. The advantages of the proposed converter are demonstrated through a comprehensive comparison study with related bipolar converters, where it achieves the highest voltage gain and lowest voltage stress on switches.
- 6 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (8) , 11476-11487
A Novel High Step-Up Nonisolated Quadratic Boost Converter for Integration of Photovoltaic and Fuel-Cell Systems Into Bipolar DC Microgrids
This article proposes a two switch high-voltage-gain quadratic boost (QB) DC–DC converter, utilizing voltage multiplier techniques using a built-in transformer to increase the voltage gain and provide bipolar output. The topology of the proposed converter offers continuous input current (CIC) as well as a common ground (CG) between the input source and the output neutral point. The maximum voltage stress on the switches is a quarter of the total output voltage. The voltage gain versus duty cycle and voltage stress on switches can be improved by increasing the turn ratios of built-in transformer. Theoretical analysis and experimental results are provided based on a 400 W prototype with ${\rm \pm}$ 280 V output voltage from a 30 V DC source with an efficiency of 93.3%. The aforementioned characteristics make the converter well suited for use as an interface between renewable energy sources, such as photovoltaic or fuel cell systems, and bipolar DC microgrids. The advantages of the proposed converter are demonstrated through a comprehensive comparison study with related bipolar converters, where it achieves the highest voltage gain and lowest voltage stress on switches.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 14 (1) , 284-293
A Novel High-Gain Nonisolated Quasi Z -Source DC–DC Converter With Symmetric Bipolar Outputs
This paper proposes a single-switch, high-voltage-gain quasi Z-source (qZS) DC-DC converter that employs voltage multiplier techniques to boost the voltage gain and deliver a bipolar output. The proposed topology ensures a continuous input current (CIC) and provides a common ground (CG) between the input and output, while limiting the semiconductor voltage stress to half of the total output voltage. A 256W prototype with ± 360V output demonstrates a voltage gain of 11.5 and an efficiency of 93.4%. Theoretical analysis, experimental verification, and a comprehensive comparison study, with state-of-the-art converters substantiate the performance advantages of the proposed design. With its high voltage gain, common grounding, CIC, and single-switch self-balancing configuration, the converter is ideally suited as an interface for renewable energy sources, such as photovoltaic systems, and bipolar DC microgrids.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 14 (1) , 284-293
A Novel High-Gain Nonisolated Quasi Z -Source DC–DC Converter With Symmetric Bipolar Outputs
This paper proposes a single-switch, high-voltage-gain quasi Z-source (qZS) DC-DC converter that employs voltage multiplier techniques to boost the voltage gain and deliver a bipolar output. The proposed topology ensures a continuous input current (CIC) and provides a common ground (CG) between the input and output, while limiting the semiconductor voltage stress to half of the total output voltage. A 256W prototype with ± 360V output demonstrates a voltage gain of 11.5 and an efficiency of 93.4%. Theoretical analysis, experimental verification, and a comprehensive comparison study, with state-of-the-art converters substantiate the performance advantages of the proposed design. With its high voltage gain, common grounding, CIC, and single-switch self-balancing configuration, the converter is ideally suited as an interface for renewable energy sources, such as photovoltaic systems, and bipolar DC microgrids.
- 6 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (7) , 9898-9907
A Novel Open-Circuit Fault Detection and Localization Method for the CLLC Converter
This article proposes a novel method for open-circuit fault detection and localization (OCFDL) in CLLC converters, which is characterized by high speed and independence from output load. The precise location of the open-circuit fault (OCF) is rapidly identified using voltage waveforms across the terminals of the resonance tank capacitor. After fault detection (FD), the converter employs a backup leg to address the issue and ensure uninterrupted power transmission. Compared to existing OCFDL methods, the proposed approach offers lower complexity, reduced implementation costs, and load independence. Experimental validation using a laboratory prototype demonstrates the theoretical advantages of the method in terms of speed, robustness, and effectiveness. Experimental results confirm the proposed method's ability to accurately detect and localize faults within 25 $\mu \text{s}$ and replace the faulty switch, ensuring reliable operation.
- 6 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (7) , 9898-9907
A Novel Open-Circuit Fault Detection and Localization Method for the CLLC Converter
This article proposes a novel method for open-circuit fault detection and localization (OCFDL) in CLLC converters, which is characterized by high speed and independence from output load. The precise location of the open-circuit fault (OCF) is rapidly identified using voltage waveforms across the terminals of the resonance tank capacitor. After fault detection (FD), the converter employs a backup leg to address the issue and ensure uninterrupted power transmission. Compared to existing OCFDL methods, the proposed approach offers lower complexity, reduced implementation costs, and load independence. Experimental validation using a laboratory prototype demonstrates the theoretical advantages of the method in terms of speed, robustness, and effectiveness. Experimental results confirm the proposed method's ability to accurately detect and localize faults within 25 $\mu \text{s}$ and replace the faulty switch, ensuring reliable operation.
- 3 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (4) , 6097-6106
A Novel Coupled Winding Nonisolated Quasi-Z-Source High Step-Up DC–DC Converter With Low Input Current Ripple
This article introduces an innovative single-switch, nonisolated quasi-Z-source (qZ–S) dc–dc converter. The goal is to develop a structure with minimal input current ripple (ICR) and high voltage gain relative to the duty cycle. The ICR is nearly eliminated by incorporating a small inductor alongside single-core coupled inductors (CIs). Increasing the turn ratio of the CIs within a voltage multiplier cell enhances the voltage gain while reducing voltage stress on the semiconductors. The proposed converter also features soft switching in the diodes and a shared ground between input and output. It employs a single mosfet switch to achieve these benefits. The performance of the new converter is evaluated and compared with other z–source and qZ–S converters. Experimental results from a 315-W prototype confirm the theoretical analysis, demonstrating a voltage gain of 12 and an efficiency of 94%. The input current ripple is less than 5%, the lowest among similar converters and other approaches like interleaved converters. These characteristics make the converter highly suitable for renewable energy applications such as photovoltaic and fuel cell systems.
- 3 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (4) , 6097-6106
A Novel Coupled Winding Nonisolated Quasi-Z-Source High Step-Up DC–DC Converter With Low Input Current Ripple
This article introduces an innovative single-switch, nonisolated quasi-Z-source (qZ–S) dc–dc converter. The goal is to develop a structure with minimal input current ripple (ICR) and high voltage gain relative to the duty cycle. The ICR is nearly eliminated by incorporating a small inductor alongside single-core coupled inductors (CIs). Increasing the turn ratio of the CIs within a voltage multiplier cell enhances the voltage gain while reducing voltage stress on the semiconductors. The proposed converter also features soft switching in the diodes and a shared ground between input and output. It employs a single mosfet switch to achieve these benefits. The performance of the new converter is evaluated and compared with other z–source and qZ–S converters. Experimental results from a 315-W prototype confirm the theoretical analysis, demonstrating a voltage gain of 12 and an efficiency of 94%. The input current ripple is less than 5%, the lowest among similar converters and other approaches like interleaved converters. These characteristics make the converter highly suitable for renewable energy applications such as photovoltaic and fuel cell systems.