Andrey V. Ripetskiy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Andrey V. Ripetskiy has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Arevshad Vartanyan
Lomonosov Moscow State University
1 shared publication - Artur A. Koltakov
JSC Ecolibri
1 shared publication - Evgeni A. Pelikh
Moscow Aviation Institute (National Research University, MAI)
1 shared publication - Georgi Hayriyan
Institute of Water Problems and Hydro-Engineering Named After I.V. Yeghiazarov
1 shared publication - Hovhannes Tokmajyan
Institute of Water Problems and Hydro-Engineering Named After I.V. Yeghiazarov
1 shared publication - Mikhail Kuprikov
Moscow Aviation Institute
1 shared publication
Latest Publications
- Open Access
- 17 November 2025
- Published by Samara National Research University in Ontology of Designing
- Vol. 15 (4) , 614-628
Topology optimization of components using an implicit geometric model representation
This paper explores methods for topological optimization of structures and the particularities of their implementation. It describes lattice and other complex geometric structures with regularly repeating unit cells that provide non-solid internal filling of components, taking into account the feasibility of their fabrication using additive manufacturing technologies. A case study of topological optimization using an implicit geometric model representation was conducted for a component intended for production via selective laser melting of metal powder alloys. The optimization resulted in a 27% reduction in the component’s mass without compromising its mechanical strength, achieved through modification of the internal geometry. The study emphasizes the importance of verifying the results of topological optimization under operational loads while accounting for the specific characteristics of additive manufacturing technologies.
- 17 November 2025
- Published by Samara National Research University in Ontology of Designing
- Vol. 15 (4) , 614-628
Open AccessTopology optimization of components using an implicit geometric model representation
This paper explores methods for topological optimization of structures and the particularities of their implementation. It describes lattice and other complex geometric structures with regularly repeating unit cells that provide non-solid internal filling of components, taking into account the feasibility of their fabrication using additive manufacturing technologies. A case study of topological optimization using an implicit geometric model representation was conducted for a component intended for production via selective laser melting of metal powder alloys. The optimization resulted in a 27% reduction in the component’s mass without compromising its mechanical strength, achieved through modification of the internal geometry. The study emphasizes the importance of verifying the results of topological optimization under operational loads while accounting for the specific characteristics of additive manufacturing technologies.
- 30 December 2024
- Published by Armenian National Association of Hydraulic Research NGO in BULLETIN OF HIGH TECHNOLOGY
- p. 11-22
DEVELOPMENT OF WATER-RETAINING CARTRIDGES WITH POLYMER-MINERAL MATERIAL
To ensure the normal functioning of plants, light, heat, water, nutrients and air are necessary. Increasing the yield and quality of cultivated crops can be achieved with the help of systems for monitoring and controlling the processes of growing plants and environment (soil and atmosphere), applied fertilizers and missing irrigation water. The addition of polymer-mineral material (PMM) to the soil, a new innovative material, created at Moscow State University (Research Institute of Mechanics), by mixing them as well as the installation of water-retaining cartridges of various shapes with a predetermined amount of PMM in it, increase its moisture capacity, allow saving an additional volume of water for plant nutrition accumulated from precipitation or artificial irrigation. Standard designs of cartridges of various shapes, pre-designed and manufactured using additive technologies, installed in containers with soil or in the open ground, allow for the accumulation of additional moisture for plants, reduce the metered consumption of irrigation water by 2 times and when used in the open ground in rain-filled conditions of the middle zone of Russia, practically eliminate it, by increasing the moisture capacity of the soil by 20–30 % (PMM dissolved in water increases its viscosity tenfold).
- 30 December 2024
- Published by Armenian National Association of Hydraulic Research NGO in BULLETIN OF HIGH TECHNOLOGY
- p. 11-22
DEVELOPMENT OF WATER-RETAINING CARTRIDGES WITH POLYMER-MINERAL MATERIAL
To ensure the normal functioning of plants, light, heat, water, nutrients and air are necessary. Increasing the yield and quality of cultivated crops can be achieved with the help of systems for monitoring and controlling the processes of growing plants and environment (soil and atmosphere), applied fertilizers and missing irrigation water. The addition of polymer-mineral material (PMM) to the soil, a new innovative material, created at Moscow State University (Research Institute of Mechanics), by mixing them as well as the installation of water-retaining cartridges of various shapes with a predetermined amount of PMM in it, increase its moisture capacity, allow saving an additional volume of water for plant nutrition accumulated from precipitation or artificial irrigation. Standard designs of cartridges of various shapes, pre-designed and manufactured using additive technologies, installed in containers with soil or in the open ground, allow for the accumulation of additional moisture for plants, reduce the metered consumption of irrigation water by 2 times and when used in the open ground in rain-filled conditions of the middle zone of Russia, practically eliminate it, by increasing the moisture capacity of the soil by 20–30 % (PMM dissolved in water increases its viscosity tenfold).