Ignace Jarrige
Research Subjects
Ignace Jarrige has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Guillaume Marcaud
AWS Center for Quantum Computing 91106 Pasadena CA USA
4 shared publications Jiansong Gao
AWS Center for Quantum Computing, Pasadena, USA
3 shared publicationsMatthew Hunt
AWS Center for Quantum Computing, Pasadena, USA
3 shared publicationsRachel Resnick
AWS Center for Quantum Computing, Pasadena, USA
3 shared publicationsSandra Diez
AWS Center for Quantum Computing, Pasadena, USA
3 shared publications- Cliff Chen
AWS Center for Quantum Computing
2 shared publications
Latest Publications
- Open Access
- 16 August 2025
- Published by Springer Nature in Communications Materials
- Vol. 6 (1) , 1-7
Low-loss superconducting resonators fabricated from tantalum films grown at room temperature
The use of α -tantalum in superconducting circuits has enabled a considerable improvement in the coherence time of transmon qubits. The standard approach to grow α -tantalum thin films on silicon involves heating the substrate, which takes several hours per deposition and prevents the integration of this material with wafers containing temperature-sensitive components. We report a detailed experimental study of an alternative growth method of α -tantalum on silicon, which is achieved at room temperature through the use of a niobium seed layer. Despite a substantially higher density of oxygen-rich grain boundaries in the films sputtered at room temperature, resonators made from these films are found to have state-of-the-art quality factors, comparable to resonators fabricated from tantalum grown at high temperature. This finding challenges previous assumptions about correlations between material properties and microwave loss of superconducting thin films, and opens a new avenue for the integration of tantalum into fabrication flows with limited thermal budget.
- 16 August 2025
- Published by Springer Nature in Communications Materials
- Vol. 6 (1) , 1-7
Open AccessLow-loss superconducting resonators fabricated from tantalum films grown at room temperature
The use of α -tantalum in superconducting circuits has enabled a considerable improvement in the coherence time of transmon qubits. The standard approach to grow α -tantalum thin films on silicon involves heating the substrate, which takes several hours per deposition and prevents the integration of this material with wafers containing temperature-sensitive components. We report a detailed experimental study of an alternative growth method of α -tantalum on silicon, which is achieved at room temperature through the use of a niobium seed layer. Despite a substantially higher density of oxygen-rich grain boundaries in the films sputtered at room temperature, resonators made from these films are found to have state-of-the-art quality factors, comparable to resonators fabricated from tantalum grown at high temperature. This finding challenges previous assumptions about correlations between material properties and microwave loss of superconducting thin films, and opens a new avenue for the integration of tantalum into fabrication flows with limited thermal budget.
- Open Access
Improving the lifetime of aluminum-based superconducting qubits through atomic layer etching and deposition
We present a dry surface treatment combining atomic layer etching and deposition (ALE and ALD) to mitigate dielectric loss in fully fabricated superconducting quantum devices formed from aluminum thin films on silicon. The treatment, performed as a final processing step prior to device packaging, starts by conformally removing the native metal oxide and fabrication residues from the exposed surfaces through ALE before \textit{in situ} encapsulating the metal surfaces with a thin dielectric layer using ALD. We measure a two-fold reduction in loss attributed to two-level system (TLS) absorption in treated aluminum-based resonators and planar transmon qubits. Treated transmons with compact capacitor plates and gaps achieve median $Q$ and $T_1$ values of $3.69 \pm 0.42 \times 10^6$ and $196 \pm 22$~$μ$s, respectively. These improvements were found to be sustained over several months. We discuss how the combination of ALE and ALD reverses fabrication-induced surface damages to significantly and durably improve device performance via a reduction of the TLS defect density in the capacitive elements.Open AccessImproving the lifetime of aluminum-based superconducting qubits through atomic layer etching and deposition
We present a dry surface treatment combining atomic layer etching and deposition (ALE and ALD) to mitigate dielectric loss in fully fabricated superconducting quantum devices formed from aluminum thin films on silicon. The treatment, performed as a final processing step prior to device packaging, starts by conformally removing the native metal oxide and fabrication residues from the exposed surfaces through ALE before \textit{in situ} encapsulating the metal surfaces with a thin dielectric layer using ALD. We measure a two-fold reduction in loss attributed to two-level system (TLS) absorption in treated aluminum-based resonators and planar transmon qubits. Treated transmons with compact capacitor plates and gaps achieve median $Q$ and $T_1$ values of $3.69 \pm 0.42 \times 10^6$ and $196 \pm 22$~$μ$s, respectively. These improvements were found to be sustained over several months. We discuss how the combination of ALE and ALD reverses fabrication-induced surface damages to significantly and durably improve device performance via a reduction of the TLS defect density in the capacitive elements. - Open Access
- 28 January 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (4)
Efficient methods for extracting superconducting resonator loss in the single-photon regime
Superconducting micro-resonators have application in sensors and quantum computing. Measurement of the resonator internal loss in the single-photon regime is a common tool to study the origins of dissipation, noise, and decoherence in quantum circuits, as well as characterization of materials used for quantum devices. However, such measurements are challenging and time-consuming with large uncertainties due to the poor signal-to-noise ratio when measured at single-photon power levels. We developed methods to extract a subset of the resonator fitting parameters at high power and fix them in the analysis of low power data, which reduce the parameter space in the regression analysis. By comparing the analysis with and without partial extraction, we show that these methods reduce the uncertainty of the results, while improving the robustness and efficiency of the loss measurement.
- 28 January 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (4)
Open AccessEfficient methods for extracting superconducting resonator loss in the single-photon regime
Superconducting micro-resonators have application in sensors and quantum computing. Measurement of the resonator internal loss in the single-photon regime is a common tool to study the origins of dissipation, noise, and decoherence in quantum circuits, as well as characterization of materials used for quantum devices. However, such measurements are challenging and time-consuming with large uncertainties due to the poor signal-to-noise ratio when measured at single-photon power levels. We developed methods to extract a subset of the resonator fitting parameters at high power and fix them in the analysis of low power data, which reduce the parameter space in the regression analysis. By comparing the analysis with and without partial extraction, we show that these methods reduce the uncertainty of the results, while improving the robustness and efficiency of the loss measurement.
- Open Access
Low-Loss Superconducting Resonators Fabricated from Tantalum Films Grown at Room Temperature
The use of $α$-tantalum in superconducting circuits has enabled a considerable improvement of the coherence time of transmon qubits. The standard approach to grow $α$-tantalum thin films on silicon involves heating the substrate, which takes several hours per deposition and prevents the integration of this material with wafers containing temperature-sensitive components. We report a detailed experimental study of an alternative growth method of $α$-tantalum on silicon, which is achieved at room temperature through the use of a niobium seed layer. Despite a substantially higher density of oxygen-rich grain boundaries in the films sputtered at room temperature, resonators made from these films are found to have state-of-the-art quality factors, comparable to resonators fabricated from tantalum grown at high temperature. This finding challenges previous assumptions about correlations between material properties and microwave loss of superconducting thin films, and opens a new avenue for the integration of tantalum into fabrication flows with limited thermal budget.
Open AccessLow-Loss Superconducting Resonators Fabricated from Tantalum Films Grown at Room Temperature
The use of $α$-tantalum in superconducting circuits has enabled a considerable improvement of the coherence time of transmon qubits. The standard approach to grow $α$-tantalum thin films on silicon involves heating the substrate, which takes several hours per deposition and prevents the integration of this material with wafers containing temperature-sensitive components. We report a detailed experimental study of an alternative growth method of $α$-tantalum on silicon, which is achieved at room temperature through the use of a niobium seed layer. Despite a substantially higher density of oxygen-rich grain boundaries in the films sputtered at room temperature, resonators made from these films are found to have state-of-the-art quality factors, comparable to resonators fabricated from tantalum grown at high temperature. This finding challenges previous assumptions about correlations between material properties and microwave loss of superconducting thin films, and opens a new avenue for the integration of tantalum into fabrication flows with limited thermal budget.