Michelangelo Fichera
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Michelangelo Fichera has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Massimo Del Bubba
Department of Chemistry, University of Florence, Via della Lastruccia 3, 50019 Sesto Fiorentino, Florence, Italy
2 shared publications Abdelaziz Baçaoui
Laboratory of Applied Chemistry and Biomass. Faculty of Sciences Semlalia. Cadi Ayyad University, Marrakech, Morocco
1 shared publication- Ayoub El Ghadraoui
Bio-Hub, Euro-BioImaging ERIC, Heidelberg, Germany
1 shared publication Daniela Santianni
Publiacqua S.P.A, Florence, Italy
1 shared publicationDonatella Fibbi
Gestione Impianti di Depurazione Acque (G.I.D.A.) S.P.A, Prato, Italy
1 shared publication- Ezio Ranieri
Dipartimento di Biologia, Università degli Studi di Bari, Via Orabona 4, 70126 Bari, Italy
1 shared publication
Latest Publications
- Open Access
- 31 March 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (7) , 3395
Vegetal Waste as a Sustainable Option to Boost Sorption for the Efficient Removal of Steroid Hormones in Constructed Wetlands
Steroid hormones (SHs) have a high estrogenic potential, and urban wastewater is one of their main ways into the aquatic environment. Constructed wetlands (CWs) are considered one of the most sustainable alternatives for the treatment of wastewater from small communities. However, the use of gravel and sand implies a significant environmental impact associated with their extraction and transport. A more sustainable alternative is the use of plant residues, as they are abundant, inexpensive, and readily available, and they can improve the efficiency of hormone removal through sorption. Thus, the sorption of 15 SHs was studied on conventional, mineral substrates (gravel, sand, and volcanic ash) and alternative vegetal wastes, i.e., mulches from giant reed, palm tree, balsa wood, and pine needles. These materials were characterized by determining their Point of Zero Charge (pHPZC), ash content, content of leachable polycyclic aromatic hydrocarbons (PAH) and heavy metals, total surface area (BET), and pore characteristics. Results indicated that SH sorption on the mineral substrates was quite low, in most cases less than 10–15%. However, in the mulches it reached between 50 and 95%, except for corticosteroids (11–43%). The pseudo-second-order kinetics provided the best fit in all cases, with R2 values between 0.97 and 0.9999. Experiments with a contact time of 7 days showed that the palm tree was the only substrate that completely removed the three corticosteroids studied (cortisone, prednisone, and prednisolone). Additionally, a significant correlation was observed between removal due to sorption (%) and log octanol–water partition coefficient (log Kow). Freundlich isotherm provided a higher number of best fits than Langmuir. Lastly, to compare sand with palm mulch under more realistic experimental conditions, four lab-scale CWs (two with palm mulch and two with sand, with/without plants) were studied. The sand-based CWs achieved faster SH percentage removals, while after 24 h, SH mass removals were significantly higher in the palm mulch-based CWs.
- 31 March 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (7) , 3395
Open AccessVegetal Waste as a Sustainable Option to Boost Sorption for the Efficient Removal of Steroid Hormones in Constructed Wetlands
Steroid hormones (SHs) have a high estrogenic potential, and urban wastewater is one of their main ways into the aquatic environment. Constructed wetlands (CWs) are considered one of the most sustainable alternatives for the treatment of wastewater from small communities. However, the use of gravel and sand implies a significant environmental impact associated with their extraction and transport. A more sustainable alternative is the use of plant residues, as they are abundant, inexpensive, and readily available, and they can improve the efficiency of hormone removal through sorption. Thus, the sorption of 15 SHs was studied on conventional, mineral substrates (gravel, sand, and volcanic ash) and alternative vegetal wastes, i.e., mulches from giant reed, palm tree, balsa wood, and pine needles. These materials were characterized by determining their Point of Zero Charge (pHPZC), ash content, content of leachable polycyclic aromatic hydrocarbons (PAH) and heavy metals, total surface area (BET), and pore characteristics. Results indicated that SH sorption on the mineral substrates was quite low, in most cases less than 10–15%. However, in the mulches it reached between 50 and 95%, except for corticosteroids (11–43%). The pseudo-second-order kinetics provided the best fit in all cases, with R2 values between 0.97 and 0.9999. Experiments with a contact time of 7 days showed that the palm tree was the only substrate that completely removed the three corticosteroids studied (cortisone, prednisone, and prednisolone). Additionally, a significant correlation was observed between removal due to sorption (%) and log octanol–water partition coefficient (log Kow). Freundlich isotherm provided a higher number of best fits than Langmuir. Lastly, to compare sand with palm mulch under more realistic experimental conditions, four lab-scale CWs (two with palm mulch and two with sand, with/without plants) were studied. The sand-based CWs achieved faster SH percentage removals, while after 24 h, SH mass removals were significantly higher in the palm mulch-based CWs.
- 11 January 2025
- Published by Elsevier in Chemosphere
- Vol. 372, 144067
Optimizing biochar-based column filtration systems for enhanced pollutant removal in wastewater treatment: A preliminary study
- 11 January 2025
- Published by Elsevier in Chemosphere
- Vol. 372, 144067
Optimizing biochar-based column filtration systems for enhanced pollutant removal in wastewater treatment: A preliminary study
- Open Access
- 9 May 2024
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 31 (24) , 35249-35265
Biochar from co-pyrolysis of biological sludge and woody waste followed by chemical and thermal activation: end-of-waste procedure for sludge management and biochar sorption efficiency for anionic and cationic dyes
Nine biochars were produced by co-pyrolysis of sawdust and biological sludge following the “design of experiment” approach. Two kinds of sludge (both deriving from the treatment of mixed industrial-municipal wastewater) and two types of woody waste were selected as categorical predicting variables, while contact time, pyrolysis temperature, and sludge percentage were used as quantitative variables. Biochars were analysed for their product characteristics and environmental compatibility based on the European Standards (EN 12915–1:2009) for materials intended for water treatment (i.e. ash content, water leachable polycyclic aromatic hydrocarbons (PAHs) and elements), as well as for specific surface area (SSA), using them as response variables of a multivariate partial least square multiple regression, whose results provided interesting insights on the relationships between pyrolysis conditions and biochar characteristics. Biochars produced with sludge and/or providing the highest SSA values (258–370 m2 g−1) were selected to undergo a sustainable chemical treatment using a by-product of the gasification of woody biomass, complying in all cases with European Standards and achieving therefore the end-of-waste status for sewage sludge. The biochar deriving from the highest percentage of sludge (30% by weight) and with the highest SSA (390 m2 g−1) was thermally activated achieving SSA of 460 m2 g−1 and then tested for the sorption of direct yellow 50 and methylene blue in ultrapure water and real wastewater, compared to a commercial activated carbon (AC). The biochar showed Langmuir sorption maxima (Qm) 2–9 times lower than AC, thus highlighting promising sorption performances. Qm for methylene blue in wastewater (28 mg‧g−1) was confirmed by column breakthrough experiments.
- 9 May 2024
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 31 (24) , 35249-35265
Open AccessBiochar from co-pyrolysis of biological sludge and woody waste followed by chemical and thermal activation: end-of-waste procedure for sludge management and biochar sorption efficiency for anionic and cationic dyes
Nine biochars were produced by co-pyrolysis of sawdust and biological sludge following the “design of experiment” approach. Two kinds of sludge (both deriving from the treatment of mixed industrial-municipal wastewater) and two types of woody waste were selected as categorical predicting variables, while contact time, pyrolysis temperature, and sludge percentage were used as quantitative variables. Biochars were analysed for their product characteristics and environmental compatibility based on the European Standards (EN 12915–1:2009) for materials intended for water treatment (i.e. ash content, water leachable polycyclic aromatic hydrocarbons (PAHs) and elements), as well as for specific surface area (SSA), using them as response variables of a multivariate partial least square multiple regression, whose results provided interesting insights on the relationships between pyrolysis conditions and biochar characteristics. Biochars produced with sludge and/or providing the highest SSA values (258–370 m2 g−1) were selected to undergo a sustainable chemical treatment using a by-product of the gasification of woody biomass, complying in all cases with European Standards and achieving therefore the end-of-waste status for sewage sludge. The biochar deriving from the highest percentage of sludge (30% by weight) and with the highest SSA (390 m2 g−1) was thermally activated achieving SSA of 460 m2 g−1 and then tested for the sorption of direct yellow 50 and methylene blue in ultrapure water and real wastewater, compared to a commercial activated carbon (AC). The biochar showed Langmuir sorption maxima (Qm) 2–9 times lower than AC, thus highlighting promising sorption performances. Qm for methylene blue in wastewater (28 mg‧g−1) was confirmed by column breakthrough experiments.