RZRoman Zolotyi

Roman Zolotyi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Roman Zolotyi has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    СТАН І ПЕРСПЕКТИВИ РОЗВИТКУ ТА МОДЕРНІЗАЦІЇ ШНЕКОВИХ НАВАНТАЖУВАЧІВ ДЛЯ ЗАВАНТАЖЕННЯ СИПУЧИХ МАТЕРІАЛІВ

    by Ігор Поливаний, Роман Золотий, Юрій Микитів

    Шнекові навантажувачі — важливе обладнання в різних галузях промисловості, таких як агропромисловий комплекс, будівництво і хімічна індустрія. Вони використовуються для транспортування сипучих матеріалів, таких як зерно, цемент, пісок і гранули, завдяки своїй простій конструкції, надійності та ефективності. Основна проблема при їх використанні — обмеження в роботі з матеріалами з високою вологістю або стиснутими матеріалами. Виробники постійно вдосконалюють конструкції шнеків і матеріали для підвищення ефективності та збільшення терміну служби. Шнекові транспортери мають компактний дизайн і дозволяють здійснювати безперервне і безпечне транспортування сипучих матеріалів. Вони використовуються не лише для обробки сипучих матеріалів, але й в гірничій і будівельній техніці. В роботі проведено дослідження транспортування піску за допомогою шнекового транспортера, де вивчалися параметри, такі як швидкість обертання та радіальний зазор. Результати експерименту дозволяють визначити оптимальні умови для забезпечення високої продуктивності при транспортуванні піску, вивчаючи вплив різних параметрів на ефективність процесу. Згідно з результатами експериментів, радіальний зазор є важливим параметром для забезпечення високої продуктивності шнекового транспортування піску. Найкращі результати досягались при зазорі, що в 1,5-2 рази перевищує розмір частки матеріалу, але не менше 3 міліметрів. Це дозволяє уникнути застрягання матеріалу та забезпечити безперебійну роботу шнекового транспорту. Отже, оптимізація цього параметра є критично важливою для підвищення ефективності транспортування піску та інших сипучих матеріалів.

  • Research of Technological Process Operations for Manufacturing Shredder Knives on Screw Spirals

    by Ivan Нevko, Andrii Diachun, Taras Dubynyak, Oleg Stibailo, Roman Zolotyi

    Ivan Нevko, Professor, Doctor of Science, Professor of the Automobile Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0001-5170-0857, e-mail: gevkoivan1@ukr.net Andrii Diachun, Associate Professor, PhD (Candidate of Technical Sciences), Associate Professor of the Mechanical Engineering Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0003-1354-9468, e-mail: dyachun_andriy@ukr.net Taras Dubynyak, Associate Professor, PhD in Technical Sciences (Candidate of Technical Sciences), Associate Professor of the Department of Instruments and Control and Measurement Systems, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0003-1529-6951, e-mail: d_taras@ukr.net Oleg Stibailo, PhD student, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0009-0007-9680-5426, e-mail: oleh.stibailo@gmail.com Roman Zolotyi, Associate Professor, PhD (Candidate of Technical Sciences), Associate Professor of the Computer-Integrated Technologies Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0002-9435-2642, e-mail: Zolotyy@gmail.com Screw working bodies with shredder knives and blade elements have been used in various industries, such as construction, food and processing, mining and agriculture. The advantages of such screws are the combination of the movement of agricultural and other materials with various technological operations of their processing, in particular, crushing and mixing. Such augers are widely used in the production of materials, compound feeds and other agricultural feeds for feeding animals and poultry, when mixing loose materials and grinding root crops. Therefore, technological support for the manufacture of shredder knives on screw spirals in medium-volume production is an important task. The purpose of the work is experimental research and practical implementation of the operations of the technological process of manufacturing shredder knives on screw spirals. The research and practical implementation of the main operations of the technological process of manufacturing shredder knives on screw spirals are presented, including grinding and sharpening the outer edge of the screw spiral, cutting the outer edge of the screw spiral to obtain blanks for shredder knives, and bending them. To perform the above operations, special technological equipment and tools were designed and manufactured. A special mandrel was designed and manufactured for clamping, basing and machining the screw spiral, a special tool for sharpening the screw edge and a roller for bending the knives of the shredders. Experimental studies were conducted to determine the patterns of the relationship between the design parameters of the knives of screw crushers, in particular the angle of bending of the screw sector, the angular value of the segment sector, the thickness of the screw material with the bending force of the screw segment. Statistical processing of experimental research results was carried out to obtain regression equations in coded and natural values of the dependence of the bending force of the screw segment on its constructive independent variable parameters, as well as checking the adequacy of the obtained equations using application software. The maximum value of the bending force of the screw segment was 1484 N, and the minimum was 496 N. An increase in the bending angle of the screw sector from 40 degrees to 80 degrees leads to an increase in the bending force of the screw segment by 1.26 times.


  • Open Access

    Improvement of the Thermophysical Characteristics of Polymer Composites Designed to Protect Water Transport

    by Oleksandr Sapronov, Andriy Buketov, Pavlo Maruschak, Serhii Zinchenko, Olga Syzonenko, Anna Sapronova, Serhii Yakushchenko, Kostyantyn Klevtsov, Oleksandr Sharko, Roman Zolotyy, et al.

    The thermophysical properties of polymeric materials filled with the refractory compounds titanium carbide (TiC) and ferrite (Fe 3 C) were studied using thermogravimetric and differential thermal analysis. These techniques allow structural transformations in modern materials to be assessed. Composites containing an active additive at a concentration of q = 0.100 wt% exhibit the lowest relative mass loss ( ε m = 65.3%), due to the formation of a significant number of bonds between the polymer components and redistribution of thermal energy within the polymer volume. Comprehensive studies of the thermal stability parameters ( T i , T f i n , T max , and T 0 ) established the course of physicochemical processes during the thermal degradation of filled composites. The activation energy increased by 1.2 times. The thermal stability of the developed polymers containing 0.100 wt% particles of the synthesized iron/TiC mixture increases from 587 K to 612 K. The rational introduction of the filler into the polymer matrix increases the stiffness of the segments and the main chain due to the presence of TiC (20%) and Fe 3 C (5%), which are formed after high‐voltage electric discharge (HVED) synthesis. The active particles of refractory compounds serve as centers for the formation of an additional spatial polymer network, ensuring the redistribution of thermal energy within the polymer volume. It has been proven that the key parameter affecting the permissible temperature range of the developed polymers is the initial exoeffect temperature (Ti), which is 485.4 K.


  • The Results of Experimental Studies of the Quality of Bulk Materials Mixing by an Automated Installation of a Screw Conveyor with a Rotating Casing

    by Andrii Diachun, Ivan Нevko, Roman Zolotyi, Serhii Koval, Oleg Derysh

    Andrii Diachun, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, e-mail: dyachun_andriy@ukr.net, ORCID ID: 0000-0003-1354-9468 Ivan Нevk, Professor, Doctor in Technics (Doctor of Technic Sciences), Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, e-mail: gevkoivan1@ukr.net, ORCID ID: 0000-0001-5170-0857 Roman Zolotyi,, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, e-mail: Zolotyy@gmail.com, ORCID ID: 0000-0002-9435-2642 Serhii Koval, post-graduate, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, e-mail: gevkoivan1@ukr.net, ORCID ID: 0009-0005-8175-9258 Oleg Derysh, post-graduate, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, e-mail: oleh161999@gmail.com, ORCID ID: 009-0000-4028-1239 Andrii Bryksa, post-graduate, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID ID: 0009-0001-3223-0682 The study of the effectiveness of mixing process by screw conveyor using analytical methods is difficult and does not provide sufficient accuracy, so experimental studies with the design and manufacture of screw conveyor installations, in particular with rotating casings, are important. The purpose of the work is to conduct and present the results of experimental research on the bulk materials mixing quality using an automated installation of a screw conveyor with a rotating casing. A prototype of an automated screw conveyor with adjustable material supply in the area of loading from the hopper and with provided rotary movement of the casing in the direction of rotation of the screw for simultaneous mixing and transportation of bulk materials was developed and manufactured. The experimental studies were conducted to determine the relationship between the structural and technological parameters of the screw conveyor-mixer, in particular the rotation frequency of the screw, the rotation frequency of the casing, the angle of inclination of the screw mixer, with the coefficient of inhomogeneity of mixing a combination of different bulk materials: grains of corn, millet, peas, wheat, buckwheat. Statistical processing of data from the results of experimental studies was carried out to obtain regression equations in coded and natural values of the dependence of the coefficient of inhomogeneity of mixing by a screw conveyor on its constructive and technological independent variable parameters, as well as checking the adequacy of the obtained equations using application software. It was established that with a decrease in the rotation frequency of the screw and an increase in the rotation frequency of the casing and the angle of inclination of the screw mixer, the value of the coefficient of inhomogeneity of the mixing of three-component and two-component mixtures decreases. The maximum value of the coefficient of inhomogeneity of the three-component mixture of corn, buckwheat and millet grains was 11.28%, and the minimum value was 7.32%. The coefficient of inhomogeneity of mixing of a two-component mixture by a screw mixer with a rotating casing is 1.64 times smaller than the coefficient of inhomogeneity of mixing by a conventional screw conveyor with a spiral screw working body within the studied screw rotation frequencies from 250 rpm to 350 rpm.